Platform Version: 4.0.4
HiBurn Version: 4.0.10
HiSilicon Technologies Co., Ltd. All rights reserved. (C) 2011-2014
Mod: Hi3798MV100-CA
Platform Version: 4.0.4
HiBurn Version: 4.0.10
HiSilicon Technologies Co., Ltd. All rights reserved. (C) 2011-2014
Mod: Hi3798MV100-CA
串口已经连接，请给单板上电，若已经上电，请断电后重新上电。
################################ ---- 10%
################################ ---- 20%
################################ ---- 30%
################################ ---- 40%
################################ ---- 51%
################################ ---- 61%
################################ ---- 71%
################################ ---- 81%
################################ ---- 92%
######################### ---- 100%
Initializing DDR ... OK
Starting DDR training ... OK
Starting fastboot ...
System startup
Reg Version: v1.1.0
Reg Time: 2016/2/25 9:23:54
Reg Name: hi3798mdmo1g_hi3798mv100_ddr3_1gbyte_16bitx2_4layers_emmc.reg
Relocate Boot to DDR
Jump to DDR
Compressed-boot v1.0.0
Uncompress......................
.
Ok
System startup
Reg Version: v1.1.0
Reg Time: 2016/2/25 9:23:54
Reg Name: hi3798mdmo1g_hi3798mv100_ddr3_1gbyte_16bitx2_4layers_emmc.reg
Relocate Boot to DDR
Jump to DDR
Fastboot 3.
3.0-00
709-ga3bdc60-dirty (liuhh@HW-TV-S5) (Jul 07 2016 - 12:33:43)
Fastboot: Version 3.3.0
Build Date: Jul 7 2016, 12:34:51
CPU: Hi3798Mv100 (CA)
Boot Media: eMMC
DDR Size: 1GB
Check nand flash controller v610. found
Special NAND id table Version 1.36
Nand ID: 0x00 0x00
0x00 0x00 0x00 0x00 0x00 0x00
No NAND device found!!!
MMC/SD
controller initialization.
MMC/SD Card:
MID: 0
x11
Read Block: 512 Bytes
Write Block: 512 Bytes
Chip Size: 7456M Bytes (High Capacity)
Name: "008G3"
Chip Type: MMC
Version:
4.0
Speed: 52000000Hz
Bus Width: 8
bit
Boot Addr: 0 Bytes
Boot Env on eMMC
Env
Offs
et: 0x00100000
Env
Size: 0x00010000
Env Range: 0x00010000
HI_OTP_LockIdWord,327: ID_WORD have already been locked
start download process.
Send command: setenv serverip 192.168.1.4
[EOT](OK)
Send command: setenv ethaddr 00:32:dc:db:fa:7c
[EOT](OK)
Send command: setenv ipaddr 192.168.1.0
[EOT](OK)
Send command: setenv netmask 255.255.0.0
[EOT](OK)
Send command: setenv gatewayip 192.168.1.1
[EOT](OK)
Tftp server Download Home switched to <C:\Users\Administrator\Desktop\HiTool\123>
Send command: tftp 0x1000000 fastboot.img
Eth up port phy at 0x01 is connect
Eth down port phy at 0x1f is connect
Hisilicon ETH net controler
MAC: 00-32-DC-DB-FA-7C
up/down PHY not link.
[EOT](ERROR)
执行命令失败，可能的原因如下：
1.请检查当前单板Flash与烧写分区中的Flash类型是否一致；
2.当前fastboot不支持该命令；
网络下载TFTP超时，可能的原因如下：
1.检查HiBurn中网络配置是否正确，具体方法参考帮助文档FAQ10.1；
2.检查PC上是否有TFTP服务器占用当前69端口。
3.检查Fastboot中网络驱动部分是否正确；
4.打开工具菜单栏上的窗口->首选项->HiBurn->TFTP设置，关闭勾选TFTP加速，然后再进行烧写；
5.使用外部的TFTP32工具进行烧写，具体方法参考帮助文档FAQ10.2。
Failed to downlaod file. Please check the board status and connection, then try again.
Failed to download fastboot! |
网站导航
楼主: pdl888
[复制链接]
发表于 2018-3-21 15:43
znds.com 