N1刷了armbian后网口速度只有100m，ethtool命令强制指定1000m无效

taul · 发表于 2024-2-17 13:54

root@aml:~# ethtool eth0
Se**ngs for eth0:
      Supported ports: [ TP MII ]
      Supported link modes: 10baseT/Half 10baseT/Full
                              100baseT/Half 100baseT/Full
                              1000baseT/Full
      Supported pause frame use: Symmetric Receive-only
      Supports auto-negotiation: Yes
      Supported FEC modes: Not reported
      Advertised link modes:  10baseT/Half 10baseT/Full
                              100baseT/Half 100baseT/Full
                              1000baseT/Full
      Advertised pause frame use: No
      Advertised auto-negotiation: Yes
      Advertised FEC modes: Not reported
      Link partner advertised link modes:  10baseT/Half 10baseT/Full
                                          100baseT/Half 100baseT/Full
      Link partner advertised pause frame use: Symmetric
      Link partner advertised auto-negotiation: Yes
      Link partner advertised FEC modes: Not reported
   Speed: 100Mb/s
      Duplex: Full
      Port: MII
      PHYAD: 0
      Transceiver: internal
      Auto-negotiation: on
      Supports Wake-on: ug
      Wake-on: d
      Current message level: 0x0000003f (63)
                           drv probe link timer ifdown ifup
      Link detected: yes

taul · 发表于 2024-2-17 16:18

本帖最后由 taul 于 2024-2-17 16:47 编辑

自问自答吧，N1比较挑网线，自己做了一根6的线重新刷机已经识别到1000M了，之前用的5e，顺带换了armbian的最新版本。
root@armbian:~# ethtool eth0
Se**ngs for eth0:
      Supported ports: [ TP MII ]
      Supported link modes: 10baseT/Half 10baseT/Full
                              100baseT/Half 100baseT/Full
                              1000baseT/Full
      Supported pause frame use: Symmetric Receive-only
      Supports auto-negotiation: Yes
      Supported FEC modes: Not reported
      Advertised link modes:  10baseT/Half 10baseT/Full
                              100baseT/Half 100baseT/Full
                              1000baseT/Full
      Advertised pause frame use: Symmetric Receive-only
      Advertised auto-negotiation: Yes
      Advertised FEC modes: Not reported
      Link partner advertised link modes:  10baseT/Half 10baseT/Full
                                          100baseT/Half 100baseT/Full
                                          1000baseT/Full
      Link partner advertised pause frame use: Symmetric
      Link partner advertised auto-negotiation: Yes
      Link partner advertised FEC modes: Not reported
      Speed: 1000Mb/s
      Duplex: Full
      Auto-negotiation: on
      master-slave cfg: preferred slave
      master-slave status: slave
      Port: Twisted Pair
      PHYAD: 0
      Transceiver: external
      MDI-X: Unknown
      Supports Wake-on: ug
      Wake-on: d
      Current message level: 0x0000003f (63)
                           drv probe link timer ifdown ifup
      Link detected: yes

› 你问我答 / 玩机教程 / 固件 › 你问我答

N1刷了armbian后网口速度只有100m，ethtool命令强制指定 ...

N1刷了armbian后网口速度只有100m，ethtool命令强制指定1000m无效

相关帖子