请教大神MG101无法输入命令是怎么回事

raijin · 发表于 2021-4-6 23:07

手里有一个咪咕盒子，标签型号为MG101，焊接ttl后显示乱码，然后根据https://www.znds.com/forum.php?mod=viewthread&tid=1023109这个帖子焊接了断开的焊点，跑码正常了，但是跑到最后无法输入命令，有大神能指点一下是什么原因吗？
跑码结果如下
Bootrom start
Boot from eMMC
Starting fastboot ...

System startup
DDRS
Reg Version:  v1.1.0
Reg Time:    2016-12-13 14:04:40
Reg Name:    hi3798mdmo1g_hi3798mv100_ddr3_768mbyte_16bitx2_4layers_emmc.reg

Jump to DDR

Fastboot 3.3.0-dirty (wentong.cen@tmajor) (Dec 13 2016 - 17:01:54)

Fastboot:    Version 3.3.0
Build Date: Dec 13 2016, 17:02:46
CPU:          Hi3798Mv100
Boot Media: eMMC
DDR Size:    1GB

Check nand flash controller v610. found
Special NAND id table Version 1.36
Nand ID: 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
No NAND device found!!!

MMC/SD controller initialization.
MMC/SD Card:
MID:       0xf4
Read Block:  512 Bytes
Write Block: 512 Bytes
Chip Size: 3728M Bytes (High Capacity)
Name:       "Biwin"
Chip Type: MMC
Version:    4.5
Speed:    52000000Hz
Bus Width: 8bit
Boot Addr: 0 Bytes

Boot Env on eMMC
Env Offset:       0x00100000
Env Size:          0x00010000
Env Range:          0x00010000
HI_OTP_LockIdWord,327: ID_WORD have already been locked

SDK Version: HiSTBAndroidV600R001C00SPC064_v2016090620

press the key!!
get key 0 2
get chipid =137980100
get chipType (HI3798MV100)
count=5
get chipid =137980100
get chipType (HI3798MV100)
count=5
entry_module===kernel
entry_factory_flag == 0
termflag = 0
--termflag:0,devicenumflag:1,devicenumlen:8,deviceid_len:15,stbmac:003403FF000333100001A8BD3A9D8129

[STB_INFO] SN:003403FF000333100001A8BD3A9D8129111003310574722MG100-U3
[STB_INFO] MAC: A8BD3A9D8129
[STB_INFO] deviceid: 111003310574722
um_mac:A8BD3A9D8129
um_serial:003403FF000333100001A8BD3A9D8129
um_deviceid:111003310574722
[um_set_mac]MAC :[A8:BD:3A:9D:81:29]  now set ethaddr.
str_serial:003403FF000333100001A8BD3A9D8129
str_deviceid:111003310574722

Reserve Memory
Start Addr:       0x2FFFE000
Bound Addr:       0x8D33000
Free  Addr:       0x2EB9D000
Alloc Block:  Addr       Size
               0x2FBFD000    4194304
               0x2F8FC000    3145728
               0x2F87B000    524288
               0x2F878000    8192
               0x2F843000    212992
               0x2F742000    1048576
               0x2F73E000    12288
               0x2F3B9000    3686400
               0x2F223000    1658880
               0x2EE9E000    3686400
               0x2EBA0000    3133440
               0x2EB9D000    8192

Hibernate!! drv  phyaddr 0x2FC00000
Hibernate!! user api phyaddr 0x2F900000
Hibernate!! userapi  start 0x14B00000, size 0x800000
Hibernate!! drv  start 0x15300000, size 0x800000
Hibernate!! flag start 0x15B00000, size 0x800000
Hibernate!! data start 0x16300000, size 0x12C00000
Press Ctrl+C to stop autoboot

MMC read: dev # 0, block # 327680, count 20480 ... 20480 blocks read: OK

33521107 Bytes/s

Found Initrd at 0x04000000 (Size 400817 Bytes), align at 16384 Bytes

## Booting kernel from Legacy Image at 01ffffc0 ...
Image Name: Linux-3.10.0_s40
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 7877240 Bytes = 7.5 MiB
Load Address: 02000000
Entry Point:  02000000
XIP Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
unionman private == 220
libphy: PHY himii:1f not found
CMD0 err 0
CMD0 err 0
CMD0 err 0
init: /init.bigfish.rc: 80: invalid option 'sdcard_r'
init: /init.bigfish.rc: 205: invalid option '//add'
init: load loaderdb finish!
init: start set ro.product.model:MG100-U3
init: /dev/hw_random not found
init: cannot open '/initlogo.rle'
init: Start mount system t:1
init: End mount t:1
init: Start mount userdata t:1
init: firstboot:1
CMD0 err 0
init: End mount t:1
init: Start mount cache t:1
init: End mount t:1
init: Start mount keydata t:1
init: End mount t:1
init: /dev/hw_random not found
healthd: No charger supplies found
init: cannot find '/system/bin/rild', disabling 'ril-daemon'
init: cannot find '/system/bin/dbus-daemon', disabling 'dbus'
CMD0 err 0
init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery'
init: cannot find '/system/bin/frontPanel', disabling 'frontPanel'
init: cannot find '/system/bin/mtkbt', disabling 'blueangel'
init: cannot find '/system/bin/dtvserver', disabling 'dtvserver'
init: cannot find '/system/bin/gpio-led', disabling 'gpio-led'
init: cannot find '/system/bin/usb-driver', disabling 'usb-driver'
init: property 'sys.powerctl' doesn't exist while expanding '${sys.powerctl}'
init: powerctl: cannot expand '${sys.powerctl}'
init: property 'sys.sysctl.extra_free_kbytes' doesn't exist while expanding '${sys.sysctl.extra_free_kbytes}'
init: cannot expand '${sys.sysctl.extra_free_kbytes}' while writing to '/proc/sys/vm/extra_free_kbytes'
CMD0 err 0
----------------HAHAHAHHAHAHA-----------------
----------------HAHAHAHHAHAHA-----------------
----------------HAHAHAHHAHAHA-----------------
----------------HAHAHAHHAHAHA-----------------
----------------HAHAHAHHAHAHA-----------------
----------------HAHAHAHHAHAHA-----------------
----------------HAHAHAHHAHAHA-----------------
----------------HAHAHAHHAHAHA-----------------
----------------HAHAHAHHAHAHA-----------------
----------------HAHAHAHHAHAHA-----------------
----------------HAHAHAHHAHAHA-----------------
EXT4-fs (sda1): unable to read superblock
----------------HAHAHAHHAHAHA-----------------
UDF-fs: error (device sda1): udf_read_tagged: read failed, block=256, location=256
UDF-fs: error (device sda1): udf_read_tagged: tag version 0x0000 != 0x0002 || 0x0003, block 0
UDF-fs: error (device sda1): udf_read_tagged: read failed, block=512, location=512
UDF-fs: error (device sda1): udf_read_tagged: tag version 0x0000 != 0x0002 || 0x0003, block 0
UDF-fs: error (device sda1): udf_read_tagged: tag version 0x0000 != 0x0002 || 0x0003, block 0
UDF-fs: error (device sda1): udf_read_tagged: read failed, block=256, location=256
UDF-fs: error (device sda1): udf_read_tagged: read failed, block=512, location=512
----------------HAHAHAHHAHAHA-----------------
----------------HAHAHAHHAHAHA
----------------HAHAHAHHAHAHA aready modify
----------------HAHAHAHHAHAHA
----------------HAHAHAHHAHAHA aready modify
----------------HAHAHAHHAHAHA
----------------HAHAHAHHAHAHA aready modify
--------net_priority already--------
--------ipv4_on already--------
--------ipv6_on already--------
--------ethernet_ipv6_mode already--------
init: untracked pid 2528 exited
==> rtl8188e_iol_efuse_patch
RTL871X: nolinked power save leave
RTL871X: rtw_set_802_11_connect(wlan0)  fw_state=0x00000008
RTL871X: start auth
RTL871X: auth success, start assoc
RTL871X: assoc success
IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
RTL871X: recv eapol packet
RTL871X: send eapol packet
RTL871X: recv eapol packet
RTL871X: send eapol packet
RTL871X: set pairwise key camid:4, addr:8c:dc:02:f9:1d:5a, kid:0, type:AES
RTL871X: set group key camid:5, addr:8c:dc:02:f9:1d:5a, kid:1, type:TKIP
device wlan0 entered promiscuous mode
device wlan0 left promiscuous mode

raijin · 发表于 2021-4-6 23:08

感觉最后这一段----------------HAHAHAHHAHAHA-----------------是对刷机者红果果的侮辱

shiyinhui · 发表于 2021-4-7 11:07

直接强刷就好

ZNDS_Tong · 发表于 2021-9-18 07:29

raijin 发表于 2021-4-6 23:08
感觉最后这一段----------------HAHAHAHHAHAHA-----------------是对刷机者红果果的侮辱

奸商肯定在主板动了手脚。

› 你问我答 / 玩机教程 / 固件 › 你问我答

请教大神MG101无法输入命令是怎么回事

请教大神MG101无法输入命令是怎么回事