魔百盒cm101s成功救砖分享！

roc5668 · 发表于 2017-11-25 09:11

学习学习

cjy1982 · 发表于 2017-11-28 16:55

jsm 发表于 2017-4-26 09:01
fastboot.bin以压缩文件删除后面的rar

请教，我的cm101s，用hitool刷了分区文件，fastboot，recovery，system（原机备份）
但是还是启动不了，黑屏

putty 跑的结果如下，请帮忙看看

Bootrom start
Boot from eMMC
Starting fastboot ...

System startup
DDRS
Reg Version:  v1.1.0
Reg Time:    2016/7/6 15:22:53
Reg Name:    hi3798mdmo1g_hi3798mv100_ddr3_1gbyte_16bitx2_4layers_8Q40E_emmc.reg

Jump to DDR

Fastboot 3.3.0 (liuyunlei@server180) (Jul 06 2016 - 15:37:08)

Fastboot:    Version 3.3.0
Build Date: Jul  6 2016, 15:38:08
CPU:          Hi3798Mv100
Boot Media: eMMC
DDR Size:    1GB

Check nand flash controller v610. found
Special NAND id table Version 1.36
Nand ID: 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
No NAND device found!!!

MMC/SD controller initialization.
MMC/SD Card:
MID:       0x70
Read Block:  512 Bytes
Write Block: 512 Bytes
Chip Size: 7456M Bytes (High Capacity)
Name:       "M3250"
Chip Type: MMC
Version:    4.0
Speed:    52000000Hz
Bus Width: 8bit
Boot Addr: 0 Bytes
HI_OTP_LockIdWord,327: ID_WORD have already been locked

SDK Version: HiSTBAndroidV600R001C00SPC064_v2016060803

[Android_Main,41] begin
[sw_ptable_init,171] begin
partition addr : [0xb19]
[swfastboot_flash_read,36]BaseAddress:0x200000, DataSize:0x100000, offset:0x0, bytes:0xb10
[sw_ptable_check,294]cksum [0xc7ce], ptable->checksum[0xc7ce]
[sw_ptable_init,184] data at 0xc7ce is ok
[swfastboot_flash_read,36]BaseAddress:0x300000, DataSize:0x100000, offset:0x0, bytes:0xb10
[sw_ptable_check,294]cksum [0xc7ce], ptable->checksum[0xc7ce]
0       fastboot 0x000000000    0x000200000
1       partition 0x000200000    0x000200000
2       recovery 0x000400000    0x001000000
3       deviceinfo 0x001400000    0x000200000
4       baseparam 0x001600000    0x000800000
5          pqparam 0x001E00000    0x000800000
6             logo 0x002600000    0x000800000
7       fastplay 0x002E00000    0x002800000
8             boot 0x005600000    0x001000000
9             misc 0x006600000    0x000200000
10          factory 0x006800000    0x001800000
11          system 0x008000000    0x027000000
12          cache 0x02F000000    0x017C00000
13          backup 0x046C00000    0x017C00000
14             swdb 0x05E800000    0x003000000
15       userdata 0x061800000    0x081000000
ptable info:2M(fastboot),2M(partition),16M(recovery),2M(deviceinfo),8M(baseparam),8M(pqparam),8M(logo),40M(fastplay),16M(boot),2M(misc),24M(factory),624M(system),380M(cache),380M(backup),48M(swdb),2064M(userdata)
[sw_ptable_init,222] ok
[sw_devinfo_init,34] begin
deviceinfo addr : [0x001400000]
[swfastboot_flash_read,36]BaseAddress:0x1400000, DataSize:0x100000, offset:0x0, bytes:0x514
[sw_devinfo_check,175] start...
[sw_devinfo_check,193] ok,checksum:0x506d
[sw_devinfo_init,53] data at 0x001400000 is ok
[0] count:[4] name:[serialno] value:[0]
[1] count:[4] name:[mac] value:[FF:FF:FF:FF:FF:FF]
[2] count:[4] name:[standard] value:[1080i_50Hz]
[3] count:[4] name:[secureline] value:[0]
[sw_devinfo_init,80] ok
[sw_set_gpio,265]
[swfastboot_flash_read,36]BaseAddress:0x5600000, DataSize:0x100000, offset:0x0, bytes:0x2000
disable serial,use default cmdline:[mem=1G console=NULL,115200 blkdevparts=mmcblk0:2M(fastboot),2M(partition),16M(recovery),2M(deviceinfo),8M(baseparam),8M(pqparam),8M(logo),40M(fastplay),16M(boot),2M(misc),24M(factory),624M(system),380M(cache),380M(backup),48M(swdb),2064M(userdata)]
get standard swstandard:1080i_50Hz g_auto_adp:0
bootargs:[mem=1G console=NULL,115200 blkdevparts=mmcblk0:2M(fastboot),2M(partition),16M(recovery),2M(deviceinfo),8M(baseparam),8M(pqparam),8M(logo),40M(fastplay),16M(boot),2M(misc),24M(factory),624M(system),380M(cache),380M(backup),48M(swdb),2064M(userdata) androidboot.force_open_console=none androidboot.mac=FF:FF:FF:FF:FF:FF androidboot.standard=1080i_50Hz androidboot.serialno=0]
sw_ir_detect_recovery begin  500 count
sw_ir_detect_recovery ok
[swfastboot_flash_read,36]BaseAddress:0x6600000, DataSize:0x100000, offset:0x0, bytes:0x10000
boot normal!!!
bootimg now: mmc read 0 0x1FFFFC0 2b000 8000;bootimg 0x1FFFFC0
[Android_Main,72] ok

SDK Version: HiSTBAndroidV600R001C00SPC064_v2016060803

Reserve Memory
Start Addr:       0xFFFE000
Bound Addr:       0x8D4A000
Free  Addr:       0xF8F9000
Alloc Block:  Addr       Size
               0xFBFD000    4194304
               0xF8FC000    3145728
               0xF8F9000    8192

[abortboot,108] begin
[abortboot,113] open loader keyed
Press Ctrl+C to stop autoboot

MMC read: dev # 0, block # 176128, count 32768 ... 32768 blocks read: OK

87192416 Bytes/s

kernel  @ ffffffff (-1 bytes)
ramdisk @ ffffffff (-1 bytes)
page size @ -1 bytes

爱吃甜甜圈 · 发表于 2017-12-28 00:21

当前单板flash与烧写分区中的flash貌似不一致

546454 · 发表于 2018-1-13 07:50

群主能把固件给我份吗？，加我qq371611271

wx_fTCkNMLK · 发表于 2018-1-15 00:05

@jsm

大神，请问一下救砖的时候hitool里的串口com要设置多少? 是在我的电脑又见查看连接usbttl后显示com几是几吗？我的好像com4。还是都要设置com5?
还有板端配置里的ip地址要填写多少啊？电脑和机顶盒在同一个网络里，我不知道机顶盒的ip地址，已成砖了，这样的话怎么填写ip地址呢

15062132889 · 发表于 2018-1-26 12:13

下载下来的不是文件

langren80 · 发表于 2018-2-5 23:04

这个必须要支持你

langren80 · 发表于 2018-2-6 14:01

高手在当贝啊！学习了

马踏飞燕耶 · 发表于 2018-2-8 15:51

高手在当贝啊！学习了

ad02dj · 发表于 2018-2-19 22:49

cy0077 发表于 2017-5-2 09:03
recovery.img解压出错

怎样才可以解压啊？

› 运营商IPTV / 有线电视 / 广电机顶盒 › 中国移动魔百盒

魔百盒cm101s成功救砖分享！

魔百盒cm101s成功救砖分享！