B860AV1.1刷机过程中遇到的奇怪问题

flycrm · 发表于 2026-1-13 17:42

本帖最后由 flycrm 于 2026-1-13 18:13 编辑

B860AV1.1的机顶盒，原机已经被刷过系统，因担心后台不干净，准备重新刷机。原机显示是安卓6

测试是1+8的配置，按照版本下载了固件

该机和教程不同的是按CTRL+Z无法进入刷机模式，最后发现是按回车键可以进入

执行USB_BIN_CHECK命令进行刷机，发现每到一半左右进度开始报错（采用CUSTAR刷机命令可以看到进度）
目前的状态是连接TTL线，开机自动进入到MStar 模式。同时现在按CTRL+Z也能进入到教程一模一样的画面。

请各位大神给分析分析，是否还有方法恢复。
刷8G包故障提升为：
>> filepartload 20200000 MstarUpgrade.bin 17000 1C4860

>> mmc write.p 20200000 MBOOT 1C4860 1
secure_image_check 20200000 1C4860 MBOOT
mmc read.p 0x203c4860 MBOOT 0x20
3621 blocks written: OK

>> filepartload 20200000 MstarUpgrade.bin 1DC000 400000

>> mmc erase.p config
** Bad Signature on 0:14: expected 0x5840, got 0x0000
ERR:invalid parameter, please check partiton name!
[ERROR] do_ustar:781: Error> cmd: mmc erase.p config Fail !!
[ERROR] do_usb_bin_check:731: Upgrade Application error!

刷4G包故障提示为：
>> mmc unlzo.cont 0x20200000 0x2A2FC8F system 1
Uncompressing ...
Continue uncompressing and writing emmc...

*****ERROR:the write data size (1502208-1522688) bigger than the partition system size (68608-1502208)!*****

[ERROR] do_ustar:781: Error> cmd: mmc unlzo.cont 0x20200000 0x2A2FC8F system 1 Fail !!
[ERROR] do_usb_bin_check:731: Upgrade Application error!
<< MStar >>#

刷机失败后，开机按CTRL+Z进入的画面如下：
AC_ON
MIU0_DQS-OK
BIST0-▒▒▒
MIU0-1024_U
Start uboot

Relocation Offset is: 011d7000
[AT][MB][start ub][426]

U-Boot 2011.06-00101-g7eef671-dirty (Sep 26 2017 - 05:33:48)

[MIU INFO] miu opencreate instance at 52ee9418 with private size 80 bytes at 52ee9460
create instance at 52ee94b8 with private size 52 bytes at 52ee9500

uboot held at [52cddf60~54000000],size=013220a0
CPU  : Clippers
Board: BD_MST207C_D01A_S_CLIPPERS
DRAM:  832 MiB
Now running in RAM - U-Boot at: 53100000

eMMC: HS200 200MHz
eMMC 7.28 GB [E8FFF8h]
In: serial
Out: serial
Err: serial
Net: zte_shutdow =false
No ethernet found.
MAC:  0x58: 0xe8: 0x73: 0x2f:0x70: 0xe4
msIR_Initialize

[CPU INFO] cpu opencreate instance at 52ef99c0 with private size 44 bytes at 52ef9a08
CPUIoctl - MDrv_CMD_CPU_QueryClock
[UTOPIA INFO] close moduleNames[38]: MODULE_CPU

[AT][MBoot][Driver Init][555]

Starting logo
============= set bootargs ===============
Hit any key to stop autoboot:  0 EMAC Mem Base:93d48000
Rx buff:33d48000
RBQP:33d78000
Packet buffer:53f45090
phy [0]=78c9
MAC Address 58:E8:73:2F:70:E4
Auto-Negotiation...
AN failLink Status Speed:10 Full-duplex:0
Status Error!
word_ETH_CFG 800(Re)start EMAC...                                           0
<< MStar >>#

15936564025 · 发表于 2026-1-14 09:54

这个机型配置比较低把
我刷的只有4.4

› 你问我答 / 玩机教程 / 固件 › ZNDS刷机/救砖

B860AV1.1刷机过程中遇到的奇怪问题

B860AV1.1刷机过程中遇到的奇怪问题

站长推荐 /1