这款云盒启动日志
G12A:BL:0253b8:61aa2d;FEAT:F0F931B0:12020;POC:F;RCY:0;EMMC:0;READ:0;0.0;0.0;
bl2_stage_init 0x01
bl2_stage_init 0x81
hw id: 0x0000 - pwm id 0x01
bl2_stage_init 0xc1
bl2_stage_init 0x02
L0:0000000f
L1:00000701
L2:00008267
L3:04000000
S1:00000000
B2:00012020
B1:f0f931b0
TE: 172387
BL2 Built : 18:58:09, May 6 2022. g12a g285d703 - jenkins@walle02-sh
Board ID = 4
Set cpu clk to 24M
Set clk81 to 24M
CPU clk: 1200 MHz
Set clk81 to 166.6M
eMMC boot @ 0
sw8 s
board id: 4
Load FIP HDR DDR from eMMC, src: 0x00010200, des: 0xfffd0000, size: 0x00004000, part: 0
fw parse done
PIEI prepare done
00000000
emmc switch 1 ok
ddr saved addr:00016000
Load ddr parameter from eMMC, src: 0x02c00000, des: 0xfffd0000, size: 0x00001000, part: 0
00000000
emmc switch 0 ok
fastboot data verify
result: 255
Cfg max: 12, cur: 1. Board id: 255. Force loop cfg
LPDDR4 probe
LPDDR4_PHY_V_0_1_27-Built : 19:50:45, May 6 2022. g12a g285d703 - longyong.chen@fae02-sz
ddr clk to 1176MHz
dmc_version 0000
Check phy result
INFO : ERROR : Training has failed!
Check phy result
INFO : ERROR : Training has failed!
Check phy result
INFO : End of initialization
INFO : ERROR : Training has failed!
1D training failed
Cfg max: 12, cur: 2. Board id: 255. Force loop cfg
LPDDR4 probe
ddr clk to 1176MHz
dmc_version 0000
Check phy result
INFO : End of CA training
INFO : End of initialization
INFO : Training has run successfully!
Check phy result
INFO : End of initialization
INFO : End of read enable training
INFO : End of fine write leveling
INFO : End of read dq deskew training
INFO : End of MPR read delay center optimization
INFO : End of Write leveling coarse delay
INFO : End of read delay center optimization
INFO : Training has run successfully!
Check phy result
INFO : End of initialization
INFO : End of MPR read delay center optimization
INFO : End of write delay center optimization
INFO : End of read delay center optimization
INFO : End of max read latency training
INFO : Training has run successfully!
1D training succeed
Check phy result
INFO : End of initialization
INFO : End of 2D read delay Voltage center optimization
INFO : End of 2D read delay Voltage center optimization
INFO : End of 2D write delay Voltage center optimization
INFO : End of 2D write delay Voltage center optimization
INFO : Training has run successfully!
soc_VRef_reg_value 0x 00000024 00000025 00000024 00000024 00000024 00000024 00000023 00000024 00000024 00000022 00000026 00000022 00000024 00000024 00000024 00000025 00000023 00000023 00000025 00000023 00000022 00000025 00000022 00000022 00000023 00000025 00000024 00000026 00000024 00000024 00000024 00000024 dwc_ddrphy_apb_wr((0<<20)|(2<<16)|(0<<12)|(0xb0):0004
dram_vref_reg_value 0x 00000056
2D training succeed
auto size-- 65535DDR cs0 size: 2048MB
DDR cs1 size: 0MB
DMC_DDR_CTRL: 00c0002cDDR size: 2048MB
cs0 DataBus test pass
cs0 AddrBus test pass
non-sec scramble use zero key
ddr scramble enabled
100bdlr_step_size ps== 447
result report
boot times 0Enable ddr reg access
00000000
emmc switch 3 ok
Authentication key not yet programmed
get rpmb counter error 0x00000007
00000000
emmc switch 0 ok
Load FIP HDR from eMMC, src: 0x00010200, des: 0x01700000, size: 0x00004000, part: 0
Load BL3X from eMMC, src: 0x00078200, des: 0x01768000, size: 0x0011d200, part: 0
0.0;0.0;M3 CHK:0;cm4_sp_mode 0
[Image: g12a_v1.1.3394-fe362b0bd7 2022-02-28 16:54:43 jenkins@walle02-sh]
OPS=0x70
ring efuse init
28 0e 70 00 01 16 10 00 00 02 36 30 4d 37 33 50
[0.048212 Inits done]
secure task start!
high task start!
low task start!
boot bl31
NOTICE: BL31: v1.3(release):079690f10
NOTICE: BL31: Built : 16:11:33, Nov 8 2021
NOTICE: BL31: G12A secure boot!
NOTICE: BL31: BL33 decompress pass
INFO: BL3-2: ATOS-V2.4.4-30-g921539e #1 Fri Dec 6 01:21:23 2019 -0700 arm
INFO: BL3-2: Chip: G12A Rev: E (28:E - 70:2)
INFO: BL3-2: crypto engine DMA
INFO: BL3-2: secure time TEE
INFO: BL3-2: CONFIG_DEVICE_SECURE 0xb200000e
U-Boot 2015.01 (Jun 18 2025 - 12:05:27), Build: jenkins-SC_SY900_2240173-42011-65
DRAM: 2 GiB
Relocation Offset is: 76e39000
mmu cfg end: 0x80000000
mmu cfg end: 0x80000000
spi_post_bind(spifc): req_seq = 0
gpio: pin GPIOA_14 (gpio 78) value is 0
register usb cfg[0][1] = 0000000077f37960
NAND: get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
NAND device id: 0 ff ff ff ff ff
No NAND device found!!!
nand init failed: -6
get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
NAND device id: 0 ff ff ff ff ff
No NAND device found!!!
nand init failed: -6
MMC: aml_priv->desc_buf = 0x0000000073e2a0c0
aml_priv->desc_buf = 0x0000000073e2c400
SDIO Port B: 0, SDIO Port C: 1
co-phase 0x3, tx-dly 0, clock 400000
co-phase 0x3, tx-dly 0, clock 400000
co-phase 0x3, tx-dly 0, clock 400000
emmc/sd response timeout, cmd8, cmd->cmdarg=0x1aa, status=0x1ff2800
emmc/sd response timeout, cmd55, cmd->cmdarg=0x0, status=0x1ff2800
co-phase 0x3, tx-dly 0, clock 400000
co-phase 0x3, tx-dly 0, clock 40000000
[set_emmc_calc_fixed_adj][875]find fixed adj_delay=20
init_part() 297: PART_TYPE_AML
[mmc_init] mmc init success
Amlogic multi-dtb tool
GZIP format, decompress...
Multi dtb detected
Multi dtb tool version: v2 .
Support 4 dtbs.
aml_dt soc: g12a platform: u212 variant: 2g
dtb 0 soc: g12a plat: u212 vari: 1g
dtb 1 soc: g12a plat: u212 vari: 2g
dtb 2 soc: g12a plat: u212 vari: 3g
dtb 3 soc: g12a plat: u212 vari: 4g
Find match dtb: 1
start dts,buffer=0000000073e2ec50,dt_addr=0000000073e2ec50
get_partition_from_dts() 92: ret 0
Amlogic multi-dtb tool
Single dtb detected
parts: 18
00: logo 0000000000800000 1
01: recovery 0000000001800000 1
02: misc 0000000000800000 1
03: dtbo 0000000000800000 1
04: cri_data 0000000000800000 2
05: param 0000000001000000 2
06: boot 0000000001000000 1
set has_boot_slot = 0
07: rsv 0000000001000000 1
08: metadata 0000000001000000 1
09: vbmeta 0000000000200000 1
10: tee 0000000002000000 1
11: vendor 0000000014000000 1
12: odm 0000000008000000 1
13: system 0000000050000000 1
14: product 0000000008000000 1
15: cache 0000000046000000 2
16: ctc 0000000012c00000 1
17: data ffffffffffffffff 4
init_part() 297: PART_TYPE_AML
eMMC/TSD partition table have been checked OK!
crc32_s:0x1577dad == storage crc_pattern:0x1577dad!!!
crc32_s:0xee152b83 == storage crc_pattern:0xee152b83!!!
crc32_s:0x79f50f07 == storage crc_pattern:0x79f50f07!!!
mmc env offset: 0x4d400000
In: serial
Out: serial
Err: serial
board id is : 4
aml log : internal sys error!
reboot_mode=cold_boot
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
_verify_dtb_checksum()-3476: calc 522df03, store 522df03
_verify_dtb_checksum()-3476: calc 522df03, store 522df03
dtb_read()-3691: total valid 2
update_old_dtb()-3672: do nothing
Amlogic multi-dtb tool
GZIP format, decompress...
Multi dtb detected
Multi dtb tool version: v2 .
Support 4 dtbs.
aml_dt soc: g12a platform: u212 variant: 2g
dtb 0 soc: g12a plat: u212 vari: 1g
dtb 1 soc: g12a plat: u212 vari: 2g
dtb 2 soc: g12a plat: u212 vari: 3g
dtb 3 soc: g12a plat: u212 vari: 4g
Find match dtb: 1
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
vpu: driver version: v20190313
vpu: detect chip type: 8
vpu: clk_level default: 7(666667000Hz), max: 7(666667000Hz)
vpu: clk_level in dts: 7
vpu: vpu_power_on
vpu: set_vpu_clk
vpu: set clk: 666667000Hz, readback: 666666667Hz(0x100)
vpu: set_vpu_clk finish
vpu: vpu_module_init_config
vpp: vpp_init
vpp: vpp osd2 matrix rgb2yuv..............
hdr_func 4, hdr_process_select 0x1
cvbs: cpuid:0x28
vdac_gsw_init: 0x0
cvbs: find clk_path: 0x0
cvbs: find performance_pal config
cvbs: find performance_ntsc config
hpd_state=0
do_hpd_detect: HDMImode=1080p60hz
do_hpd_detect: colorattribute=444,8bit
Saving Environment to aml-storage...
mmc env offset: 0x4d400000
Writing to MMC(1)... done
aml_config_dtb 755
aml_config_dtb 785
co_phase = <0x00000003>
caps2 = "MMC_CAP2_HS200"
f_max = "
▒▒"
status = "disabled"
status = "okay"
Net: dwmac.ff3f0000amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 4
wipe_data=successful
wipe_cache=successful
upgrade_step=2
aml log : internal sys error!
reboot_mode:::: cold_boot
ext4logoLoadCmd=ext4load mmc 1:${logoPart} ${logoLoadAddr} ${ext4LogoPath}
8294454 bytes read in 237 ms (33.4 MiB/s)
[imgread]load bmp from ext4 part okay
bmp pixel: 32
[OSD]load fb addr from dts:/meson-fb
[OSD]set initrd_high: 0x7f800000
[OSD]fb_addr for logo: 0x7f800000
[OSD]load fb addr from dts:/meson-fb
[OSD]fb_addr for logo: 0x7f800000
[OSD]VPP_OFIFO_SIZE:0xfff01fff
[CANVAS]canvas init
[CANVAS]addr=0x7f800000 width=7680, height=2160
[OSD]osd_hw.free_dst_data: 0,719,0,575
[OSD]osd1_update_disp_freescale_enable
vpp: vpp_matrix_update: 2
cvbs_performance_enhancement
cvbs_config_hdmipll_g12a
cvbs_set_vid2_clk
vdac_enable: 1, module_sel:0x8
hdr_packet
vpp: hdr_policy = 1
vpp: Rx hdr_info.hdr_sup_eotf_smpte_st_2084 = 0
amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 4
[KM]Error:f[keymanage_dts_get_key_device]L105:oemkey key name is not exist
[KM]Error:f[_get_km_ops_by_name]L240:key oemkey not know device 4
[KM]Error:f[key_manage_query_exist]L554:There isn't dts cfg for key[oemkey]
[KM]Error:f[key_manage_query_size]L511:Fail in query key exist
[KM]Error:f[key_manage_query_size]L515:key[cmei] not programed yet
amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 4
[KM]Error:f[key_manage_query_size]L515:key[authkey] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[no_wifi] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[wifi_hide] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[stb_model] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[stb_manu] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[uart_debug] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[manu_info1] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[manu_info2] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[manu_info3] not programed yet
time_out = 7a120
key[0] = 77884cb3
key[1] = 7e814cb3
irkey - irkey <timeout> <key1> ...<keyN> - maximum value of N: 10
Usage:
irkey - No additional help available.
Command: bcb uboot-command
Start read misc partition datas!
BCB hasn't any datas,exit!
amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 4
[KM]Error:f[keymanage_dts_get_key_device]L105:oemkey key name is not exist
[KM]Error:f[_get_km_ops_by_name]L240:key oemkey not know device 4
[KM]Error:f[key_manage_query_exist]L554:There isn't dts cfg for key[oemkey]
[KM]Error:f[key_manage_query_size]L511:Fail in query key exist
[KM]Error:f[key_manage_query_size]L515:key[cmei] not programed yet
amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 4
[KM]Error:f[key_manage_query_size]L515:key[authkey] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[no_wifi] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[wifi_hide] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[stb_model] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[stb_manu] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[uart_debug] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[manu_info1] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[manu_info2] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[manu_info3] not programed yet
InUsbBurn
wait for phy ready count is 0
noSof
sof timeout, reset usb phy tuning
Hit Enter or space or Ctrl+C key to stop autoboot -- : 0
pll tsensor avg: 0x1f67, u_efuse: 0x8009
temp1: 34
ddr tsensor avg: 0x1f5f, u_efuse: 0x23
temp2: 34
device cool done
CONFIG_SYSTEM_AS_ROOT: null
system_mode: 0
Start read misc partition datas!
info->magic =
info->version_major = 1
info->version_minor = 0
info->slots[0].priority = 15
info->slots[0].tries_remaining = 7
info->slots[0].successful_boot = 0
info->slots[1].priority = 14
info->slots[1].tries_remaining = 7
info->slots[1].successful_boot = 0
info->crc32 = -1075449479
active slot = 0
CONFIG_AVB2: avb2
active_slot: normal
avb2: 1
Start read misc partition datas!
info->magic =
info->version_major = 1
info->version_minor = 0
info->slots[0].priority = 15
info->slots[0].tries_remaining = 7
info->slots[0].successful_boot = 0
info->slots[1].priority = 14
info->slots[1].tries_remaining = 7
info->slots[1].successful_boot = 0
info->crc32 = -1075449479
active slot = 0
active_slot is normal
ab_suffix is
avb_slot_verify.c:525: DEBUG: Loading vbmeta struct from partition 'vbmeta'.
AVB2 verify with default kpub
[store]To run cmd[emmc dtb_read 0x00000000749c4f50 0x40000]
dtb_read_shortcut()-3534: short cut in...
Start read misc partition datas!
info->magic =
info->version_major = 1
info->version_minor = 0
info->slots[0].priority = 15
info->slots[0].tries_remaining = 7
info->slots[0].successful_boot = 0
info->slots[1].priority = 14
info->slots[1].tries_remaining = 7
info->slots[1].successful_boot = 0
info->crc32 = -1075449479
active slot = 0
active_slot is normal
Start read misc partition datas!
info->magic =
info->version_major = 1
info->version_minor = 0
info->slots[0].priority = 15
info->slots[0].tries_remaining = 7
info->slots[0].successful_boot = 0
info->slots[1].priority = 14
info->slots[1].tries_remaining = 7
info->slots[1].successful_boot = 0
info->crc32 = -1075449479
active slot = 0
active_slot is normal
Start read misc partition datas!
info->magic =
info->version_major = 1
info->version_minor = 0
info->slots[0].priority = 15
info->slots[0].tries_remaining = 7
info->slots[0].successful_boot = 0
info->slots[1].priority = 14
info->slots[1].tries_remaining = 7
info->slots[1].successful_boot = 0
info->crc32 = -1075449479
active slot = 0
active_slot is normal
avb verification: locked = 1, result = 0
ee_gate_off ...
avb2: 1
## Booting Android Image at 0x01080000 ...
Kernel command line: androidboot.dtbo_idx=0 buildvariant=userdebug
[store]Is good fdt check header, no need decrypt!
active_slot is normal
load dtb from 0x1000000 ......
Amlogic multi-dtb tool
Single dtb detected
find 1 dtbos
dtbos to be applied: 0
Apply dtbo 0
Loading Kernel Image(COMP_NONE) ... OK
kernel loaded at 0x01080000, end = 0x01a15410
libfdt fdt_getprop(): FDT_ERR_NOTFOUND
Loading Ramdisk to 09e93000, end 09fff2e9 ... OK
Loading Device Tree to 0000000009e7c000, end 0000000009e92c52 ... OK
fdt_fixup_memory_banks, reg:0000000000000000
Starting kernel ...
uboot time: 5678256 us
[ 0.000000@0] 07400000 - 07500000, 1024 KB, ramoops@0x07400000
[ 0.000000@0] 05000000 - 07400000, 36864 KB, linux,secmon
[ 0.000000@0] 7f800000 - 80000000, 8192 KB, linux,meson-fb
[ 0.000000@0] 77800000 - 7f800000, 131072 KB, linux,ion-dev
[ 0.000000@0] 73400000 - 77800000, 69632 KB, linux,di_cma
[ 0.000000@0] 5a400000 - 73400000, 409600 KB, linux,codec_mm_cma
[ 0.000000@0] 5a400000 - 5a400000, 0 KB, linux,codec_mm_reserved
[ 0.000000@0] 59000000 - 5a400000, 20480 KB, linux,vdin1_cma
Login: start detecting wifi&Bt......
wifi detected: uwe5621
这款盒子系统为只读，输入可读写命令也无法更改。。。。翻阅资料有人说这个需要解BL
|
网站导航
发表于 2025-12-7 17:02
提升卡
置顶卡
变色卡
千斤顶
发表于 2025-12-7 21:00
楼主
/1 
znds.com 