本帖最后由 肖元元 于 2023-11-30 19:43 编辑
安徽广电九联HDC-2100K，Hi3798mv200，1+8G，有USB3.0接口，带无线的盒子，
主板上的ttl接口是接RS232串行口的，如果没有RS232的TTL小板，用CH340G小板要飞线。
方便使用可以将飞线接到焊针上。接上CH340小板跑马，小板设定工作电压是3.3伏。
开机跑马：
CPU: Hi3798Mv200
Boot Media: eMMC
DDR Size: 1GB
Found flash memory controller hifmc100.
no found nand device.
MMC/SD controller initialization.
scan edges:2 p2f:6 f2p:8
mix set temp-phase 3
scan elemnts: startp:136 endp:131
Tuning SampleClock. mix set phase:[03/07] ele:[07/18]
MMC/SD Card:
MID: 0x11
Read Block: 512 Bytes
Write Block: 512 Bytes
Chip Size: 7456M Bytes (High Capacity)
Name: "008G30"
Chip Type: MMC
Version: 5.1
Speed: 100000000Hz
Mode: HS400
Voltage: 1.8V
Bus Width: 8bit
Boot Addr: 0 Bytes
Net: eth0 phymdio(31) invalid, use default:0
upWarning: failed to set MAC address
, gmac0Warning: failed to set MAC address
Boot Env on eMMC
Env Offset: 0x00200000
Env Size: 0x00010000
Env Range: 0x00010000
SDK Version: 12-5_v2016120520
Security begin read RSA CRC Key in USB disk
Security no RSA CRC Key in USB disk
PageSize = 0x0 BlockSize = 0x2000
HI_Flash_Read read_crc = 0xffffffff crc=0x2322e93d
USB0: Register 1212 NbrPorts 2
USB EHCI 1.00
scanning bus 0 for devices... cannot reset port 1!?
2 USB Device(s) found
USB0: Register 2000140 NbrPorts 2
USB XHCI 1.00
scanning bus 0 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
usb_stor_scan not find usb dev ret=0xffffffff
suma_check_ir_key_loader in
Received key ret=0xffffffff
suma_check_ir_key_loader out
printenv parver not exist!!!
get chipid =37986200
get chipType (HI3798MV200)
count=2
PageSize = 0x0 BlockSize = 0x2000
HI_Flash_Read read_crc = 0x6b6753df crc=0x6b6753df
crc check ok
upgrd_dat.reserve[0]=0
bootname=kernel
YLJ_ADD pubkey->modulusbits=0x400 pubkey->pkexp=0x10001
YLJ_ADD u32Size=0xa00000
YLJ_ADD before break i=0x58000
YLJ_ADD Jump out while loop remain=0x900000 i=0x58000
YLJ_ADD 222 Begin!
YLJ_ADD signdata_len = 0x80
verify: Verify kernel success!
set_default_ethaddr CRC SUCCESS!!
set_default_ethaddr mac_str=74:8F:1B:C1:DF:2A
enter write OTP mode!
Reserve Memory
Start Addr: 0x3C8FE000
Bound Addr: 0x8EB5000
Free Addr: 0x3BAF9000
Alloc Block: Addr Size
0x3C4FD000 0x400000
0x3C1FC000 0x300000
0x3C17B000 0x80000
0x3C178000 0x2000
0x3C025000 0x152000
0x3C01B000 0x9000
0x3BC96000 0x384000
0x3BC92000 0x3000
0x3BAFC000 0x195000
0x3BAF9000 0x2000
Press Ctrl+C to stop autoboot
MMC read: dev # 0, block # 524288, count 10240 ... 10240 blocks read: OK
172040602 Bytes/s
Copy slave cpu bootcode from 0x00cb0370 to 0xffff0000, 4096 Bytes
## Starting Secure OS at 0x3E700000 ...
## Secure OS Image:
Header Size: 0x400 (1 KB)
Kernel Load Addresss: 0x3E008000
Kernel Size: 0x277a5c (2526 KB)
Task Number: 15
Task Total Size: 0x25EAD0 (2426 KB)
Move SecureOS kernel from 0x3E700400 to 0x3E008000, 2526KB
Move systab and strtab from 0x3E90E368 to 0x3EBD692C, 422 KB
Move TAs from 0x3E977E5C to 0x3E700400, 2426KB
## Succeed to load SecureOS
MMC read: dev # 0, block # 442368, count 20480 ... 20480 blocks read: OK
174174344 Bytes/s
Check Hisilicon_ADVCA ...
Not hisilicon ADVCA image ...
Found Initrd at 0x04000000 (Size 625529 Bytes), align at 16384 Bytes
## Booting kernel from Legacy Image at 01ffffc0 ...
Image Name: Linux-3.18.24_hi3798mv2x
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 9135793 Bytes = 8.7 MiB
Load Address: 02000000
Entry Point: 02000000
XIP Kernel Image ... OK
OK
ATAGS [0x00000100 - 0x0000051C], 1052Bytes
Starting kernel ...
TrustedCore Status:[ABCD]
TrustedCore Debug Version iCOS V100R006C10SPC002B004 base iCOS_MAIN_3.2.7, Dec 5 2016.21:14:09
Load Secure Cipher success. Build Time:[Dec 5 2016, 21:21:21]
[TEEGlobalTask]1/1/1970 0:0:0.890 TrustedCore Execute Successfully and jump to Linux kernel
Uncompressing Linux... done, booting the kernel.
Booting Linux on physical CPU 0x0
Initializing cgroup subsys cpuacct
Linux version 3.18.24_hi3798mv2x (root@ubuntu) (gcc version 4.9.2 20140904 (prerelease) (gcc-4.9.2 + glibc-2.22 (Build by czyong) Tue Oct 27 16:32:03 CST 2015) ) #1 SMP Thu Apr 12 17:08:55 CST 2018
CPU: ARMv7 Processor [410fd034] revision 4 (ARMv7), cr=10c5383d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
initmrd: found no initmrd.
Machine model: Hisilicon
cma: Reserved 56 MiB at 0x38000000
cma: Reserved 4 MiB at 0x3c400000
Memory policy: Data cache writealloc
DT missing boot CPU MPIDR[23:0], fall back to default cpu_logical_map
PERCPU: Embedded 10 pages/cpu @df42b000 s11392 r8192 d21376 u40960
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 247048
Kernel command line: androidboot.selinux=disabled console=ttyAMA0,115200 blkdevparts=mmcblk0:2M(fastboot),4M(bootargs),10M(loader),10M(loaderbak),8M(stbinfo),8M(stbinfobak),8M(upinfo),8M(upinfobak),10M(recovery),4M(deviceinfo),8M(baseparam),8M(baseparambak),8M(pqparam),20M(logo),20M(logobak),40M(fastplay),40M(fastplaybak),20M(kernel),20M(misc),40M(trustedcore),700M(system),700M(cache),128M(dvbdata),-(userdata) hbcomp=/dev/block/mmcblk0p21 initrd=0x4000000,0x98B79 mem=969M mmz=ddr,0,0,54M vmalloc=500M
log_buf_len individual max cpu contribution: 4096 bytes
log_buf_len total cpu_extra contributions: 12288 bytes
log_buf_len min size: 16384 bytes
log_buf_len: 32768 bytes
early log buf free: 13912(84%)
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 891972K/992256K available (13898K kernel code, 1862K rwdata, 4432K rodata, 619K init, 3204K bss, 100284K reserved, 404864K highmem)
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xe0000000 - 0xff000000 ( 496 MB)
lowmem : 0xc0000000 - 0xdfc00000 ( 508 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc11eec88 (18332 kB)
.init : 0xc11ef000 - 0xc1289c80 ( 620 kB)
.data : 0xc128a000 - 0xc145bb8c (1863 kB)
.bss : 0xc145bb8c - 0xc177cf0c (3205 kB)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:352
Architected cp15 timer(s) running at 24.00MHz (phys).
sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns
Switching to timer-based delay loop, resolution 41ns
sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956969942ns
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=24000)
pid_max: default: 32768 minimum: 301
Security Framework initialized
SELinux: Initializing.
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
ftrace: allocating 46305 entries in 136 pages
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0xc95b48 - 0xc95ba0
CPU: hi3798mv200
CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
Brought up 4 CPUs
SMP: Total of 4 processors activated (192.00 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
VFP support v0.3: implementor 41 architecture 3 part 40 variant 3 rev 4
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 8 bytes.
Serial: AMBA PL011 UART driver
f8b00000.uart: ttyAMA0 at MMIO 0xf8b00000 (irq = 81, base_baud = 0) is a PL011 rev2
console [ttyAMA0] enabled
f8b02000.uart: ttyAMA1 at MMIO 0xf8b02000 (irq = 83, base_baud = 0) is a PL011 rev2
f8b03000.uart: ttyAMA2 at MMIO 0xf8b03000 (irq = 84, base_baud = 0) is a PL011 rev2
pl061_gpio gpio0: PL061 GPIO chip @0xf8b20000 registered
pl061_gpio gpio1: PL061 GPIO chip @0xf8b21000 registered
pl061_gpio gpio2: PL061 GPIO chip @0xf8b22000 registered
pl061_gpio gpio3: PL061 GPIO chip @0xf8b23000 registered
pl061_gpio gpio4: PL061 GPIO chip @0xf8b24000 registered
pl061_gpio gpio5: PL061 GPIO chip @0xf8004000 registered
pl061_gpio gpio6: PL061 GPIO chip @0xf8b26000 registered
pl061_gpio gpio7: PL061 GPIO chip @0xf8b27000 registered
pl061_gpio gpio8: PL061 GPIO chip @0xf8b28000 registered
pl061_gpio gpio9: PL061 GPIO chip @0xf8b29000 registered
hisilicon-pcie: probe of f0001000.pcie failed with error -1
vgaarb: loaded
SCSI subsystem initialized
ssp-pl022 f8b1a000.spi: ARM PL022 driver, device ID: 0x00041022
ssp-pl022 f8b1a000.spi: mapped registers from 0xf8b1a000 to f9b1a000
spi_master spi0: will run message pump with realtime priority
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
hisi_iommu_ptable_addr:phy 0x1e000000 size:0x400000
hisi_iommu_err_rdaddr :phy 0x1e4b4400 size:0x200
hisi_iommu_err_wraddr :phy 0x1e4b4600 size:0x200
in hisi_iommu_domain_init start
in hisi_iommu_domain_init end
[TEEGlobalTask]1/1/1970 0:0:1.802 params:05020e00, mapping 00000000 bytes at 1ee96000
[TEEGlobalTask]1/1/1970 0:0:1.809 Do service initial build done!
Advanced Linux Sound Architecture Driver Initialized.
Bluetooth: Core ver 2.19
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO socket layer initialized
[TEEGlobalTask]1/1/1970 0:0:1.868 Do service initial build done!
[00:00:00:571 ERROR-Invalid]:DispAddIntf[674]:DISP 1 acquire (0) failed
[00:00:00:588 ERROR-Invalid]:MCE_Init[2328]:ERR: get PDM Param
Switched to clocksource arch_sys_counter
NET: Registered protocol family 2
TCP established hash table entries: 4096 (order: 2, 16384 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP: reno registered
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 612K (c4000000 - c4099000)
futex hash table entries: 1024 (order: 4, 65536 bytes)
audit: initializing netlink subsys (disabled)
audit: type=2000 audit(0.700:1): initialized
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
squashfs: version 4.0 (2009/01/31) Phillip Lougher
jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.23)
msgmni has been set to 952
bounce: pool size: 64 pages
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
io scheduler noop registered
io scheduler deadline registered (default)
io scheduler cfq registered
brd: module loaded
loop: module loaded
zram: Created 1 device(s) ...
hifmc100: registerd new interface driver hifmc100.
hifmc100: Found flash memory controller hifmc100.
hifmc100: no found spi-nor device.
hifmc100: no found nand device.
hifmc100: no found spi-nand device.
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
FEPHY:addr=2, la_am=0xe, ldo_am=0x4, r_tuning=0x18
libphy: himii: probed
hieth: attached port 0 PHY 2 to driver Generic PHY
platform f9840000.ethernet: Driver hi_gmac_v200 requests probe deferral
PPP generic driver version 2.4.2
PPP BSD Compression module registered
PPP Deflate Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
usbcore: registered new interface driver asix
usbcore: registered new interface driver ax88179_178a
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver dm9601
usbcore: registered new interface driver net1080
usbcore: registered new interface driver cdc_subset
usbcore: registered new interface driver zaurus
usbcore: registered new interface driver cdc_ncm
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-pci: OHCI PCI platform driver
usbcore: registered new interface driver cdc_wdm
usbcore: registered new interface driver usb-storage
usbcore: registered new interface driver usbserial
usbcore: registered new interface driver option
usbserial: USB Serial support registered for GSM modem (1-port)
hiudc: version 3.00a 10-AUG-2012
Core Release: 3.10a
Setting default values for core params
Using Buffer DMA mode
Dedicated Tx FIFOs mode
file system registered
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
usbcore: registered new interface driver uvcvideo
USB Video Class driver (1.1.1)
sp805-wdt f8a2c000.watchdog: registration successful
device-mapper: ioctl: 4.28.0-ioctl (2014-09-17) initialised: dm-devel@redhat.com
registered new interface driver himciV2.0_3.18.24_hi3798mv2x_20170401
mmc0: BKOPS_EN bit is not set
scan edges:2 p2f:6 f2p:8
mix set temp-phase 3
scan elemnts: startp:131 endp:125
Tuning SampleClock. mix set phase:[03/07] ele:[09/17]
mmc0: new HS400 MMC card at address 0001
mmcblk0: mmc0:0001 008G30 7.28 GiB
mmcblk0boot0: mmc0:0001 008G30 partition 1 4.00 MiB
mmcblk0boot1: mmc0:0001 008G30 partition 2 4.00 MiB
mmcblk0rpmb: mmc0:0001 008G30 partition 3 4.00 MiB
mmcblk0: p1(fastboot) p2(bootargs) p3(loader) p4(loaderbak) p5(stbinfo) p6(stbinfobak) p7(upinfo) p8(upinfobak) p9(recovery) p10(deviceinfo) p11(baseparam) p12(baseparambak) p13(pqparam) p14(logo) p15(logobak) p16(fastplay) p17(fastplaybak) p18(kernel) p19(misc) p20(trustedcore) p21(system) p22(cache) p23(dvbdata) p24(userdata)
f9820000.himciv200.SD: eMMC/MMC/SD Device NOT detected!
f9c40000.himciv200.SD: eMMC/MMC/SD Device NOT detected!
hidraw: raw HID events driver (C) Jiri Kosina
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
ashmem: initialized
logger: created 256K log 'log_main'
logger: created 256K log 'log_events'
logger: created 256K log 'log_radio'
logger: created 256K log 'log_system'
hiahci-phy: registered new sata phy driver
input: Hi keyboard as /devices/virtual/input/input0
input: Hi mouse as /devices/virtual/input/input1
input: qwerty as /devices/virtual/input/input2
Hi Android vinput driver init successful!
hiotg: registered new interface otg driver
Registering sdcardfs 2.1.3
SVB: type = 2, core vmin 870mv
usbcore: registered new interface driver snd-usb-audio
oprofile: hardware counters not available
oprofile: using timer interrupt.
GACT probability on
Mirror/redirect action on
Simple TC action Loaded
netem: version 1.3
u32 classifier
Performance counters on
input device check on
Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (13946 buckets, 55784 max)
ctnetlink v0.93: registering with nfnetlink.
xt_time: kernel timezone is -0000
IPVS: Registered protocols ()
IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
IPVS: Creating netns size=792 id=0
IPVS: ipvs loaded.
ip_tables: (C) 2000-2006 Netfilter Core Team
ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully
arp_tables: (C) 2002 David S. Miller
TCP: cubic registered
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 17
bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
Bridge firewalling registered
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bluetooth: BNEP socket layer initialized
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
Bluetooth: HIDP socket layer initialized
8021q: 802.1Q VLAN Support v1.8
lib80211: common routines for IEEE802.11 drivers
Registering SWP/SWPB emulation handler
libphy: higmac_mii_bus: probed
hisi-sndcard hisi-sndcard: aiao-hifi <-> hisi-i2s mapping ok
ALSA device list:
#0: HISI-AIAO
Freeing unused kernel memory: 616K (c11ef000 - c1289000)
init: /init.bigfish.rc: 49: invalid command 'getprop'
init: /dev/hw_random not found
init: /dev/hw_random not found
squashfs: SQUASHFS error: Can't find a SQUASHFS superblock on ram1
EXT4-fs (mmcblk0p21): mounted filesystem with ordered data mode. Opts: (null)
EXT4-fs (mmcblk0p24): recovery complete
EXT4-fs (mmcblk0p24): mounted filesystem with ordered data mode. Opts: (null)
EXT4-fs (mmcblk0p22): recovery complete
EXT4-fs (mmcblk0p22): mounted filesystem with ordered data mode. Opts: (null)
EXT4-fs (mmcblk0p23): recovery complete
EXT4-fs (mmcblk0p23): mounted filesystem with ordered data mode. Opts: (null)
EXT4-fs (mmcblk0p15): recovery complete
EXT4-fs (mmcblk0p15): mounted filesystem with ordered data mode. Opts: (null)
binder: 1559:1559 transaction failed 29189, size 0-0
init: cannot find '/system/bin/debuggerd64', disabling 'debuggerd64'
init: cannot find '/system/bin/rild', disabling 'ril-daemon'
init: cannot find '/system/bin/dbus-daemon', disabling 'dbus'
init: cannot find '/system/bin/install-recovery.sh', disabling 'flash_recovery'
init: cannot find '/system/bin/DTVServer', disabling 'DTVServer'
init: cannot find '/system/bin/paymentserver', disabling 'paymentserver'
init: cannot find '/system/bin/DCASServer', disabling 'DCASServer'
init: cannot find '/system/bin/frontPanel', disabling 'frontPanel'
init: cannot find '/system/bin/netshared', disabling 'netshared'
init: cannot find '/system/bin/dtvserver', disabling 'dtvserver'
init: cannot find '/system/bin/netmonitorserver', disabling 'netmonitorserver'
init: cannot find '/system/bin/gpio-led', disabling 'gpio-led'
init: cannot find '/system/bin/usb-driver', disabling 'usb-driver'
init: cannot find '/system/bin/skyplayserver', disabling 'skyplayserver'
init: cannot find '/system/bin/dlnaserver', disabling 'dlnaserver'
sdcardfs: version 2.1.3
sdcardfs: dev_name -> /data/media
sdcardfs: options -> fsuid=1023,fsgid=1023,mask=0,userid=0,gid=1015,reserved_mb=20
sdcardfs: mounted on top of /data/media type ext4
init: cannot find '/system/bin/adbd', disabling 'adbd'
logd.auditd: start
[00:00:02:915 ERROR-HI_PQ]:PQIoctl[933]:No Such IOCTL Command: 1074014499
random: init urandom read with 42 bits of entropy available
[14:39:52:352 ERROR-HI_IR]:IR_Config[212]:IR config over!cfg:0x1f17
[14:39:52:367 ERROR-HI_IR]:IR_Config[212]:IR config over!cfg:0x1f17
Welcome to HiAndroid
ehci-platform: EHCI generic platform driver
ehci-platform f9890000.ehci: EHCI Host Controller
ehci-platform f9890000.ehci: new USB bus registered, assigned bus number 1
ehci-platform f9890000.ehci: irq 98, io mem 0xf9890000
ehci-platform f9890000.ehci: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci-platform: OHCI generic platform driver
ohci-platform f9880000.ohci: Generic Platform OHCI controller
ohci-platform f9880000.ohci: new USB bus registered, assigned bus number 2
ohci-platform f9880000.ohci: irq 99, io mem 0xf9880000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
xhci-hcd f98a0000.xhci: xHCI Host Controller
xhci-hcd f98a0000.xhci: new USB bus registered, assigned bus number 3
xhci-hcd f98a0000.xhci: irq 101, io mem 0xf98a0000
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
xhci-hcd f98a0000.xhci: xHCI Host Controller
xhci-hcd f98a0000.xhci: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 1 port detected
rtk_btusb: RTKBT_RELEASE_NAME: 20170908_TV_ANDROID_5.x
rtk_btusb: Realtek Bluetooth USB driver module init, version 4.1.5
rtk_btusb: Register usb char device interface for BT driver
usbcore: registered new interface driver rtk_btusb
tntfs: module license 'Commercial. For support email ntfs-support@tuxera.com.' taints kernel.
Disabling lock debugging due to kernel taint
Tuxera NTFS driver 3015.10.14 [Flags: R/W MODULE].
ahci: probe of f9900000.hiahci failed with error -1
usb 1-2: new high-speed USB device number 3 using ehci-platform
usb 2-1: new full-speed USB device number 2 using ohci-platform
healthd: No charger supplies found
healthd: No battery devices found
rtk_btusb: btusb_probe: usb_interface db252c00, bInterfaceNumber 0, idVendor 0x0bda, idProduct 0x0000
rtk_btusb: get_fw_table_entry: Product id = 0xb720, fw table entry size 49
rtk_btusb: firmware_info_init: Auto suspend is disabled
rtk_btusb: btusb_probe: Check bt reset flag 0
input: Compx 2.4G Receiver as /devices/platform/soc/f9880000.ohci/usb2/2-1/2-1:1.0/0003:25A7:FA61.0001/input/input3
hid-generic 0003:25A7:FA61.0001: input,hidraw0: USB HID v1.10 Keyboard [Compx 2.4G Receiver] on usb-f9880000.ohci-1/input0
input: Compx 2.4G Receiver as /devices/platform/soc/f9880000.ohci/usb2/2-1/2-1:1.1/0003:25A7:FA61.0002/input/input4
hid-generic 0003:25A7:FA61.0002: input,hiddev0,hidraw1: USB HID v1.10 Mouse [Compx 2.4G Receiver] on usb-f9880000.ohci-1/input1
[r858_init_tuner] 2017-9-14 16:30 u32TunerPort=0, R858_ExtTunerNum=0, R858_IntTunerNum=0
random: nonblocking pool is initialized
capability: warning: `main' uses 32-bit capabilities (legacy support in use)
[r858_init_tuner] 2017-9-14 16:30 u32TunerPort=1, R858_ExtTunerNum=0, R858_IntTunerNum=1
healthd: battery none chg=
lowmemorykiller: lowmem_shrink: convert oom_adj to oom_score_adj:
lowmemorykiller: oom_adj 0 => oom_score_adj 0
lowmemorykiller: oom_adj 1 => oom_score_adj 58
lowmemorykiller: oom_adj 2 => oom_score_adj 117
lowmemorykiller: oom_adj 3 => oom_score_adj 176
lowmemorykiller: oom_adj 9 => oom_score_adj 529
lowmemorykiller: oom_adj 15 => oom_score_adj 1000
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
hieth f9c30000.hieth eth0: Link is Up - 100Mbps/Full - flow control off
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
rtk_btusb: btchr_open: BT usb char device is opening
rtk_btusb: btchr_ioctl DOWN_FW_CFG with Cmd:1074022601
rtk_btusb: get_firmware: start, cached 1,patch_entry->fw_len= 0
rtk_btusb: load_firmware: Default lmp version = 0x8723, config file name[rtl8723bu_config], fw file name[rtl8723b_fw]
rtk_btusb: rtk_update_altsettings: 1 AltSettings
rtk_btusb: ORG Config len=00000035:
rtk_btusb: 00000000: 55 ab 23 87 2f 00 f4 00 08 01 00 00 00 05 50 00
rtk_btusb: 00000010: 00 0c 00 10 02 80 92 04 50 c5 ea 19 e1 1b fd af
rtk_btusb: 00000020: 5f 01 a4 0b 27 00 01 63 fe 00 01 01 e3 01 01 04
rtk_btusb: 00000030: 7a 01 02 12 19 00 00 00 00 00 00 00 00 00 00 00
rtk_btusb: No Mac Config for BT
rtk_btusb: Final Config len=00000035:
rtk_btusb: 00000000: 55 ab 23 87 2f 00 f4 00 08 01 00 00 00 05 50 00
rtk_btusb: 00000010: 00 0c 00 10 02 80 92 04 50 c5 ea 19 e1 1b fd af
rtk_btusb: 00000020: 5f 01 a4 0b 27 00 01 63 fe 00 01 01 e3 01 01 04
rtk_btusb: 00000030: 7a 01 02 12 19 00 00 00 00 00 00 00 00 00 00 00
rtk_btusb: load_firmware: epatch_buf = vmalloc(fw->size, GFP_KERNEL)
rtk_btusb: reset_channel: status 0
rtk_btusb: reset_channel: Wait channel reset for 300ms
rtk_btusb: get_eversion: status 0, eversion 1
rtk_btusb: load_firmware: Default lmp_version 0x8723, project_id[1] 0x8723 -> match
rtk_btusb: BTCOEX:20150518-0x5c45 svn version:0x00003ae7 fw version:0x0c4d1676 rtk_btusb version:4.1.5 Cut:2, patch length:0x5e4c, patch offset:0x000058c0
rtk_btusb: load_firmware: vfree(epatch_buf)
rtk_btusb: load_firmware: fw exists, config file exists
rtk_btusb: check_fw_version: Controller lmp = 0x8723, patch lmp = 0x185f, default patch lmp = 0x8723
rtk_btusb: check_fw_version: Cold BT controller startup
rtk_btusb: download_patch: Cold reset bt chip only download
rtk_btusb: download_data: done, sent 224 frag pkts, received 224 frag events
rtk_btusb: download_patch: Download fw patch done, fw len 24193
rtk_btusb: btusb_open: Start, PM usage count 0
rtk_btusb: btusb_open: End, PM usage count 0
TTL对话只能显示，不能输入指令。
看到对应分区配置，在hitool做好分区表，备份整个盒子分区后，修改system.img镜像分区，重新刷入后可联网
看影视。
应用可以用U盘安装，也可以通过当贝桌面文件推送或当贝助手文件传输安装，系统带root，可用RE文件管理器挂载可读写做
些修改。
备份的全分区以及替换的logo，修改的system的压缩包：链接：https://pan.baidu.com/s/1dMWQ5Dha6sae1-BFwpgrxA
提取码：hwxe
海思烧写工具hi tool_5.3.16，链接：https://pan.baidu.com/s/1l0Em5oZtJx3BhL4ajoB7lA
提取码：71kk
|
网站导航
发表于 2023-11-30 19:03
收藏
淘帖
顶一个
踩
提升卡
置顶卡
变色卡
千斤顶
znds.com 