|
|
本帖最后由 智能小柠檬 于 2023-8-6 19:32 编辑
各位大佬，我有一台x96max plus 2+16,现在已将内存改成了4g，从其他旧板上拆下了螃蟹的RTL8211F千兆芯片，装到了x96max plus上，并在网上找到原理图，将外围补齐（应该是补齐了），刷了x96max plus2的固件后（同样是rtl8211f)不能启动，现将启动信息附上，各位大佬，能给个解决方法吗，或谁有此板的rtl8211f外围元件详细信息啊，能给一份吗？谢谢了undefined
SM1:BL:511f6b:81ca2f;FEAT:A0F83180:20282000;POC:F;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
bl2_stage_init 0x01
bl2_stage_init 0x81
hw id: 0x0000 - pwm id 0x01
bl2_stage_init 0xc1
bl2_stage_init 0x02
L0:00000000
L1:00000703
L2:00008067
L3:15000020
S1:00000000
B2:20282000
B1:a0f83180
TE: 284518
BL2 Built : 15:21:42, Mar 26 2020. g12a g486bc38 - gongwei.chen@droid11-sz
Board ID = 1
Set cpu clk to 24M
Set clk81 to 24M
Use GP1_pll as DSU clk.
DSU clk: 1200 Mhz
CPU clk: 1200 MHz
Set clk81 to 166.6M
eMMC boot @ 0
sw8 s
board id: 1
Load FIP HDR DDR from eMMC, src: 0x00010200, des: 0xfffd0000, size: 0x00004000, part: 0
fw parse done
PIEI prepare done
00000000
emmc switch 1 ok
ddr saved addr:00016000
Load ddr parameter from eMMC, src: 0x02c00000, des: 0xfffd0000, size: 0x00001000, part: 0
00000000
emmc switch 0 ok
fastboot data verify
result: 255
Cfg max: 12, cur: 1. Board id: 255. Force loop cfg
DDR4 probe
LPDDR4_PHY_V_0_1_21-Built : 15:37:51, Mar 26 2020. g12a gf098346 - gongwei.chen@droid11-sz
ddr clk to 1320MHz
dmc_version 0001
Check phy result
INFO : End of initialization
INFO : ERROR : Training has failed!
1D training failed
Cfg max: 12, cur: 2. Board id: 255. Force loop cfg
DDR4 probe
ddr clk to 912MHz
dmc_version 0001
Check phy result
INFO : End of initialization
INFO : ERROR : Training has failed!
1D training failed
Cfg max: 12, cur: 3. Board id: 255. Force loop cfg
DDR3 probe
ddr clk to 792MHz
dmc_version 0001
Check phy result
INFO : End of initialization
INFO : End of read enable training
INFO : End of fine write leveling
INFO : End of read dq deskew training
INFO : End of MPR read delay center optimization
INFO : End of Write leveling coarse delay
INFO : End of write delay center optimization
INFO : End of read delay center optimization
INFO : End of max read latency training
INFO : Training has run successfully!
dwc_ddrphy_apb_wr((0<<20)|(2<<16)|(0<<12)|(0xb0):00e4
1D training succeed
auto size-- 65535DDR cs0 size: 4096MB
DDR cs1 size: 0MB
DMC_DDR_CTRL: 0000002dDDR size: 3928MB
cs0 DataBus test pass
cs0 AddrBus test pass
non-sec scramble use zero key
ddr scramble enabled
100bdlr_step_size ps== 415
result report
boot times 0Enable ddr reg access
00000000
emmc switch 3 ok
BL2: rpmb counter: 0x00001220
00000000
emmc switch 0 ok
Load FIP HDR from eMMC, src: 0x00010200, des: 0x01700000, size: 0x00004000, part: 0
Load BL3X from eMMC, src: 0x00078200, des: 0x01768000, size: 0x000ed800, part: 0
0.0;M3 CHK:0;cm4_sp_mode 0
[Image: g12a_v1.1.3394-7d43064d5 2020-05-07 15:37:06 gongwei.chen@droid11-sz]
OPS=0x01
ring efuse init
2b 0b 01 00 01 22 05 00 00 18 37 34 59 56 56 50
[0.014467 Inits done]
secure task start!
high task start!
low task start!
boot bl31
NOTICE: BL31: v1.3(release):5d6723eeb
NOTICE: BL31: Built : 15:05:59, Mar 17 2020
NOTICE: BL31: G12A normal boot!
NOTICE: BL31: BL33 decompress pass
ERROR: Error initializing runtime service opteed_fast
U-Boot 2015.01 (Jul 12 2021 - 21:34:03)
DRAM: 3.8 GiB
Relocation Offset is: d6d85000
mmu cfg end: 0xe0000000
mmu cfg end: 0xe0000000
spi_post_bind(spifc): req_seq = 0
register usb cfg[0][1] = 00000000d7e99bb0
NAND: get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
NAND device id: 0 ff ff ff ff ff
No NAND device found!!!
nand init failed: -6
get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
NAND device id: 0 ff ff ff ff ff
No NAND device found!!!
nand init failed: -6
MMC: aml_priv->desc_buf = 0x00000000d3d75a70
aml_priv->desc_buf = 0x00000000d3d77db0
SDIO Port B: 0, SDIO Port C: 1
co-phase 0x3, tx-dly 0, clock 400000
co-phase 0x3, tx-dly 0, clock 400000
co-phase 0x3, tx-dly 0, clock 400000
emmc/sd response timeout, cmd8, cmd->cmdarg=0x1aa, status=0x1ff2800
emmc/sd response timeout, cmd55, cmd->cmdarg=0x0, status=0x1ff2800
co-phase 0x3, tx-dly 0, clock 400000
co-phase 0x3, tx-dly 0, clock 40000000
[set_emmc_calc_fixed_adj][875]find fixed adj_delay=20
init_part() 297: PART_TYPE_AML
[mmc_init] mmc init success
Amlogic multi-dtb tool
GZIP format, decompress...
Multi dtb detected
Multi dtb tool version: v2 .
Support 3 dtbs.
aml_dt soc: sm1 platform: ac213 variant: 4g
dtb 0 soc: g12a plat: u212 vari: 4g
dtb 1 soc: sm1 plat: ac213 vari: 2g
dtb 2 soc: sm1 plat: ac213 vari: 4g
Find match dtb: 2
start dts,buffer=00000000d3d7a620,dt_addr=00000000d3d7a620
get_partition_from_dts() 92: ret 0
Amlogic multi-dtb tool
Single dtb detected
parts: 17
00: logo 0000000000800000 1
01: recovery 0000000001800000 1
02: misc 0000000000800000 1
03: dtbo 0000000000800000 1
04: cri_data 0000000000800000 2
05: param 0000000001000000 2
06: boot 0000000001000000 1
set has_boot_slot = 0
07: rsv 0000000001000000 1
08: metadata 0000000001000000 1
09: vbmeta 0000000000200000 1
10: tee 0000000002000000 1
11: vendor 0000000046000000 1
12: odm 0000000008000000 1
13: system 0000000050000000 1
14: product 0000000008000000 1
15: cache 0000000046000000 2
16: data ffffffffffffffff 4
init_part() 297: PART_TYPE_AML
eMMC/TSD partition table have been checked OK!
crc32_s:0x1577dad == storage crc_pattern:0x1577dad!!!
crc32_s:0xee152b83 == storage crc_pattern:0xee152b83!!!
crc32_s:0x79f50f07 == storage crc_pattern:0x79f50f07!!!
mmc env offset: 0x4d400000
In: serial
Out: serial
Err: serial
reboot_mode=cold_boot
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
_verify_dtb_checksum()-3476: calc 5e40354d, store 5e40354d
_verify_dtb_checksum()-3476: calc 5e40354d, store 5e40354d
dtb_read()-3691: total valid 2
update_old_dtb()-3672: do nothing
Amlogic multi-dtb tool
GZIP format, decompress...
Multi dtb detected
Multi dtb tool version: v2 .
Support 3 dtbs.
aml_dt soc: sm1 platform: ac213 variant: 4g
dtb 0 soc: g12a plat: u212 vari: 4g
dtb 1 soc: sm1 plat: ac213 vari: 2g
dtb 2 soc: sm1 plat: ac213 vari: 4g
Find match dtb: 2
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
vpu: driver version: v20190313
vpu: detect chip type: 11
vpu: clk_level default: 7(666667000Hz), max: 7(666667000Hz)
vpu: clk_level in dts: 7
vpu: vpu_power_on
vpu: set_vpu_clk
vpu: set clk: 666667000Hz, readback: 666666667Hz(0x100)
vpu: set_vpu_clk finish
vpu: vpu_module_init_config
vpp: vpp_init
vpp: vpp osd2 matrix rgb2yuv..............
hdr_func 4, hdr_process_select 0x1
cvbs: cpuid:0x2b
cvbs: find performance_pal config
Net: Phy 0 not found
PHY reset timed out
dwmac.ff3f0000amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 4
MACADDR:02:00:00:05:22:01(from chipid)
CONFIG_AVB2: null
Start read misc partition datas!
info->magic =
info->version_major = 1
info->version_minor = 0
info->slots[0].priority = 15
info->slots[0].tries_remaining = 7
info->slots[0].successful_boot = 0
info->slots[1].priority = 14
info->slots[1].tries_remaining = 7
info->slots[1].successful_boot = 0
info->crc32 = -1075449479
active slot = 0
wipe_data=successful
wipe_cache=successful
upgrade_step=2
reboot_mode:::: cold_boot
s_version: U-Boot 2015.01
amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 4
[KM]Error:f[key_manage_query_size]L515:key[usid] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[mac] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[deviceid] not programed yet
[KM]Error:f[keymanage_dts_get_key_device]L105:oemkey key name is not exist
[KM]Error:f[_get_km_ops_by_name]L240:key oemkey not know device 4
[KM]Error:f[key_manage_query_exist]L554:There isn't dts cfg for key[oemkey]
[KM]Error:f[key_manage_query_size]L511:Fail in query key exist
hpd_state=0
do_hpd_detect: hdmimode=1080p60hz
do_hpd_detect: colorattribute=444,8bit
Saving Environment to aml-storage...
mmc env offset: 0x4d400000
Writing to MMC(1)... done
no sink, fallback to 720p60hz[4]
hdr mode is 0
dv mode is ver:0 len: 0
hdr10+ mode is 0
read hdmichecksum 0x00000000, colorattribute 444,8bit
read hdmimode 1080p60hz, colorspace <NULL>, colordepth <NULL>
do_get_parse_edid: autoMode = false, manualMode=16
isYuv4KSink: false, maxTMDSRate=150
do_get_parse_edid: non-yuv4k sink: inColorSpace: HDMI_COLOR_FORMAT_RGB
do_get_parse_edid: default inColorDepth: HDMI_COLOR_DEPTH_24B
TV is same, initial mode is: 576cvbs attr: 444,8bit
dolby_status 0
dolby_status 0
dolby_vision_process: no tv and dv disabled
Saving Environment to aml-storage...
mmc env offset: 0x4d400000
Writing to MMC(1)... done
[OSD]load fb addr from dts:/meson-fb
[OSD]load fb addr from dts:/fb
[OSD]set initrd_high: 0xdf800000
[OSD]fb_addr for logo: 0xdf800000
[OSD]load fb addr from dts:/meson-fb
[OSD]load fb addr from dts:/fb
[OSD]fb_addr for logo: 0xdf800000
[OSD]VPP_OFIFO_SIZE:0xfff01fff
[CANVAS]canvas init
[CANVAS]addr=0xdf800000 width=3840, height=2160
[OSD]osd_hw.free_dst_data: 0,719,0,575
[OSD]osd1_update_disp_freescale_enable
vpp: vpp_matrix_update: 2
cvbs_performance_enhancement
cvbs_config_hdmipll_g12a
cvbs_set_vid2_clk
dolby_status 0
dolby_status 0
hdr_packet
vpp: hdr_policy = 0
vpp: Rx hdr_info.hdr_sup_eotf_smpte_st_2084 = 0
s_version: U-Boot 2015.01
amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 4
[KM]Error:f[key_manage_query_size]L515:key[usid] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[mac] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[deviceid] not programed yet
[KM]Error:f[keymanage_dts_get_key_device]L105:oemkey key name is not exist
[KM]Error:f[_get_km_ops_by_name]L240:key oemkey not know device 4
[KM]Error:f[key_manage_query_exist]L554:There isn't dts cfg for key[oemkey]
[KM]Error:f[key_manage_query_size]L511:Fail in query key exist
gpio: pin GPIOAO_3 (gpio 3) value is 1
SARADC channel(2) is 0x3fa.
saradc - saradc sub-system
Usage:
saradc saradc open <channel> - open a SARADC channel
saradc close - close the SARADC
saradc getval - get the value in current channel
saradc test - test the SARADC by channel-7
saradc get_in_range <min> <max> - return 0 if current value in the range of current channel
Command: bcb uboot-command
Start read misc partition datas!
BCB hasn't any datas,exit!
InUsbBurn
wait for phy ready count is 0
[MSG]sof
Set Addr 16
Get DT cfg
Get DT cfg
Get DT cfg
Set Addr 17
Get DT cfg
Get DT cfg
Get DT cfg
set CFG
waitIdentifyTime(751) > timeout(750)
s_version: U-Boot 2015.01
amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 4
[KM]Error:f[key_manage_query_size]L515:key[usid] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[mac] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[deviceid] not programed yet
[KM]Error:f[keymanage_dts_get_key_device]L105:oemkey key name is not exist
[KM]Error:f[_get_km_ops_by_name]L240:key oemkey not know device 4
[KM]Error:f[key_manage_query_exist]L554:There isn't dts cfg for key[oemkey]
[KM]Error:f[key_manage_query_size]L511:Fail in query key exist
Hit Enter or space or Ctrl+C key to stop autoboot -- : 0
pll tsensor avg: 0x1f8f, u_efuse: 0x8001
temp1: 35
ddr tsensor avg: 0x1f9a, u_efuse: 0x32
temp2: 36
device cool done
CONFIG_SYSTEM_AS_ROOT: systemroot
system_mode: 1
Start read misc partition datas!
info->magic =
info->version_major = 1
info->version_minor = 0
info->slots[0].priority = 15
info->slots[0].tries_remaining = 7
info->slots[0].successful_boot = 0
info->slots[1].priority = 14
info->slots[1].tries_remaining = 7
info->slots[1].successful_boot = 0
info->crc32 = -1075449479
active slot = 0
CONFIG_AVB2: null
active_slot: normal
avb2: 0
ee_gate_off ...
avb2: 0
## Booting Android Image at 0x01080000 ...
Kernel command line: androidboot.dtbo_idx=0 --cmdline root=/dev/mmcblk0p18 buildvariant=userdebug
[store]Is good fdt check header, no need decrypt!
active_slot is normal
load dtb from 0x1000000 ......
Amlogic multi-dtb tool
Single dtb detected
find 1 dtbos
dtbos to be applied: 0
Apply dtbo 0
Loading Kernel Image(COMP_NONE) ... OK
kernel loaded at 0x01080000, end = 0x019f8020
Loading Device Tree to 0000000009fe6000, end 0000000009fff190 ... OK
fdt_fixup_memory_banks, reg:0000000000000000
Starting kernel ...
uboot time: 4961999 us
DRAM: 3.8 GiB
Relocation Offset is: d6d85000
mmu cfg end: 0xe0000000
mmu cfg end: 0xe0000000
spi_post_bind(spifc): req_seq = 0
register usb cfg[0][1] = 00000000d7e99bb0
NAND: get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
NAND device id: 0 ff ff ff ff ff
No NAND device found!!!
nand init failed: -6
get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
NAND device id: 0 ff ff ff ff ff
No NAND device found!!!
nand init failed: -6
MMC: aml_priv->desc_buf = 0x00000000d3d75a70
aml_priv->desc_buf = 0x00000000d3d77db0
SDIO Port B: 0, SDIO Port C: 1
co-phase 0x3, tx-dly 0, clock 400000
co-phase 0x3, tx-dly 0, clock 400000
co-phase 0x3, tx-dly 0, clock 400000
emmc/sd response timeout, cmd8, cmd->cmdarg=0x1aa, status=0x1ff2800
emmc/sd response timeout, cmd55, cmd->cmdarg=0x0, status=0x1ff2800
co-phase 0x3, tx-dly 0, clock 400000
co-phase 0x3, tx-dly 0, clock 40000000
[set_emmc_calc_fixed_adj][875]find fixed adj_delay=20
init_part() 297: PART_TYPE_AML
[mmc_init] mmc init success
Amlogic multi-dtb tool
GZIP format, decompress...
Multi dtb detected
Multi dtb tool version: v2 .
Support 3 dtbs.
aml_dt soc: sm1 platform: ac213 variant: 4g
dtb 0 soc: g12a plat: u212 vari: 4g
dtb 1 soc: sm1 plat: ac213 vari: 2g
dtb 2 soc: sm1 plat: ac213 vari: 4g
Find match dtb: 2
start dts,buffer=00000000d3d7a620,dt_addr=00000000d3d7a620
get_partition_from_dts() 92: ret 0
Amlogic multi-dtb tool
Single dtb detected
parts: 17
00: logo 0000000000800000 1
01: recovery 0000000001800000 1
02: misc 0000000000800000 1
03: dtbo 0000000000800000 1
04: cri_data 0000000000800000 2
05: param 0000000001000000 2
06: boot 0000000001000000 1
set has_boot_slot = 0
07: rsv 0000000001000000 1
08: metadata 0000000001000000 1
09: vbmeta 0000000000200000 1
10: tee 0000000002000000 1
11: vendor 0000000046000000 1
12: odm 0000000008000000 1
13: system 0000000050000000 1
14: product 0000000008000000 1
15: cache 0000000046000000 2
16: data ffffffffffffffff 4
init_part() 297: PART_TYPE_AML
eMMC/TSD partition table have been checked OK!
crc32_s:0x1577dad == storage crc_pattern:0x1577dad!!!
crc32_s:0xee152b83 == storage crc_pattern:0xee152b83!!!
crc32_s:0x79f50f07 == storage crc_pattern:0x79f50f07!!!
mmc env offset: 0x4d400000
In: serial
Out: serial
Err: serial
reboot_mode=cold_boot
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
_verify_dtb_checksum()-3476: calc 5e40354d, store 5e40354d
_verify_dtb_checksum()-3476: calc 5e40354d, store 5e40354d
dtb_read()-3691: total valid 2
update_old_dtb()-3672: do nothing
Amlogic multi-dtb tool
GZIP format, decompress...
Multi dtb detected
Multi dtb tool version: v2 .
Support 3 dtbs.
aml_dt soc: sm1 platform: ac213 variant: 4g
dtb 0 soc: g12a plat: u212 vari: 4g
dtb 1 soc: sm1 plat: ac213 vari: 2g
dtb 2 soc: sm1 plat: ac213 vari: 4g
Find match dtb: 2
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
vpu: driver version: v20190313
vpu: detect chip type: 11
vpu: clk_level default: 7(666667000Hz), max: 7(666667000Hz)
vpu: clk_level in dts: 7
vpu: vpu_power_on
vpu: set_vpu_clk
vpu: set clk: 666667000Hz, readback: 666666667Hz(0x100)
vpu: set_vpu_clk finish
vpu: vpu_module_init_config
vpp: vpp_init
vpp: vpp osd2 matrix rgb2yuv..............
hdr_func 4, hdr_process_select 0x1
cvbs: cpuid:0x2b
cvbs: find performance_pal config
Net: Phy 0 not found
PHY reset timed out
dwmac.ff3f0000amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 4
MACADDR:02:00:00:05:22:01(from chipid)
CONFIG_AVB2: null
Start read misc partition datas!
info->magic =
info->version_major = 1
info->version_minor = 0
info->slots[0].priority = 15
info->slots[0].tries_remaining = 7
info->slots[0].successful_boot = 0
info->slots[1].priority = 14
info->slots[1].tries_remaining = 7
info->slots[1].successful_boot = 0
info->crc32 = -1075449479
active slot = 0
wipe_data=successful
wipe_cache=successful
upgrade_step=2
reboot_mode:::: cold_boot
s_version: U-Boot 2015.01
amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 4
[KM]Error:f[key_manage_query_size]L515:key[usid] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[mac] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[deviceid] not programed yet
[KM]Error:f[keymanage_dts_get_key_device]L105:oemkey key name is not exist
[KM]Error:f[_get_km_ops_by_name]L240:key oemkey not know device 4
[KM]Error:f[key_manage_query_exist]L554:There isn't dts cfg for key[oemkey]
[KM]Error:f[key_manage_query_size]L511:Fail in query key exist
hpd_state=0
do_hpd_detect: hdmimode=1080p60hz
do_hpd_detect: colorattribute=444,8bit
Saving Environment to aml-storage...
mmc env offset: 0x4d400000
Writing to MMC(1)... done
no sink, fallback to 720p60hz[4]
hdr mode is 0
dv mode is ver:0 len: 0
hdr10+ mode is 0
read hdmichecksum 0x00000000, colorattribute 444,8bit
read hdmimode 1080p60hz, colorspace <NULL>, colordepth <NULL>
do_get_parse_edid: autoMode = false, manualMode=16
isYuv4kSink: false, maxTMDSRate=150
do_get_parse_edid: non-yuv4k sink: inColorSpace: HDMI_COLOR_FORMAT_RGB
do_get_parse_edid: default inColorDepth: HDMI_COLOR_DEPTH_24B
TV is same, initial mode is: 576cvbs attr: 444,8bit
dolby_status 0
dolby_status 0
dolby_vision_process: no tv and dv disabled
Saving Environment to aml-storage...
mmc env offset: 0x4d400000
Writing to MMC(1)... done
[OSD]load fb addr from dts:/meson-fb
[OSD]load fb addr from dts:/fb
[OSD]set initrd_high: 0xdf800000
[OSD]fb_addr for logo: 0xdf800000
[OSD]load fb addr from dts:/meson-fb
[OSD]load fb addr from dts:/fb
[OSD]fb_addr for logo: 0xdf800000
[OSD]VPP_OFIFO_SIZE:0xfff01fff
[CANVAS]canvas init
[CANVAS]addr=0xdf800000 width=3840, height=2160
[OSD]osd_hw.free_dst_data: 0,719,0,575
[OSD]osd1_update_disp_freescale_enable
vpp: vpp_matrix_update: 2
cvbs_performance_enhancement
cvbs_config_hdmipll_g12a
cvbs_set_vid2_clk
dolby_status 0
dolby_status 0
hdr_packet
vpp: hdr_policy = 0
vpp: Rx hdr_info.hdr_sup_eotf_smpte_st_2084 = 0
s_version: U-Boot 2015.01
amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 4
[KM]Error:f[key_manage_query_size]L515:key[usid] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[mac] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[deviceid] not programed yet
[KM]Error:f[keymanage_dts_get_key_device]L105:oemkey key name is not exist
[KM]Error:f[_get_km_ops_by_name]L240:key oemkey not know device 4
[KM]Error:f[key_manage_query_exist]L554:There isn't dts cfg for key[oemkey]
[KM]Error:f[key_manage_query_size]L511:Fail in query key exist
gpio: pin GPIOAO_3 (gpio 3) value is 1
SARADC channel(2) is 0x3fb.
saradc - saradc sub-system
Usage:
saradc saradc open <channel> - open a SARADC channel
saradc close - close the SARADC
saradc getval - get the value in current channel
saradc test - test the SARADC by channel-7
saradc get_in_range <min> <max> - return 0 if current value in the range of current channel
Command: bcb uboot-command
Start read misc partition datas!
BCB hasn't any datas,exit!
InUsbBurn
wait for phy ready count is 0
[MSG]sof
Set Addr 20
Get DT cfg
Get DT cfg
Get DT cfg
Set Addr 21
Get DT cfg
Get DT cfg
Get DT cfg
set CFG
waitIdentifyTime(751) > timeout(750)
s_version: U-Boot 2015.01
amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 4
[KM]Error:f[key_manage_query_size]L515:key[usid] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[mac] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[deviceid] not programed yet
[KM]Error:f[keymanage_dts_get_key_device]L105:oemkey key name is not exist
[KM]Error:f[_get_km_ops_by_name]L240:key oemkey not know device 4
[KM]Error:f[key_manage_query_exist]L554:There isn't dts cfg for key[oemkey]
[KM]Error:f[key_manage_query_size]L511:Fail in query key exist
Hit Enter or space or Ctrl+C key to stop autoboot -- : 0
pll tsensor avg: 0x1f8f, u_efuse: 0x8001
temp1: 35
ddr tsensor avg: 0x1f95, u_efuse: 0x32
temp2: 36
device cool done
CONFIG_SYSTEM_AS_ROOT: systemroot
system_mode: 1
Start read misc partition datas!
info->magic =
info->version_major = 1
info->version_minor = 0
info->slots[0].priority = 15
info->slots[0].tries_remaining = 7
info->slots[0].successful_boot = 0
info->slots[1].priority = 14
info->slots[1].tries_remaining = 7
info->slots[1].successful_boot = 0
info->crc32 = -1075449479
active slot = 0
CONFIG_AVB2: null
active_slot: normal
avb2: 0
ee_gate_off ...
avb2: 0
## Booting Android Image at 0x01080000 ...
Kernel command line: androidboot.dtbo_idx=0 --cmdline root=/dev/mmcblk0p18 buildvariant=userdebug
[store]Is good fdt check header, no need decrypt!
active_slot is normal
load dtb from 0x1000000 ......
Amlogic multi-dtb tool
Single dtb detected
find 1 dtbos
dtbos to be applied: 0
Apply dtbo 0
Loading Kernel Image(COMP_NONE) ... OK
kernel loaded at 0x01080000, end = 0x019f8020
Loading Device Tree to 0000000009fe6000, end 0000000009fff190 ... OK
fdt_fixup_memory_banks, reg:0000000000000000
Starting kernel ...
uboot time: 4863221 us启动信息最后部分：
[ 3.923304@0] meson-mmc: add_emmc_partition
[ 3.923512@0] meson-mmc: [mmcblk0p01] bootloader offset 0x000000000000, size 0x000000400000
[ 3.923690@0] meson-mmc: [mmcblk0p02] reserved offset 0x000002400000, size 0x000004000000
[ 3.923840@0] meson-mmc: [mmcblk0p03] cache offset 0x000006c00000, size 0x000046000000
[ 3.923996@0] meson-mmc: [mmcblk0p04] env offset 0x00004d400000, size 0x000000800000
[ 3.924139@0] meson-mmc: [mmcblk0p05] logo offset 0x00004e400000, size 0x000000800000
[ 3.924291@0] meson-mmc: [mmcblk0p06] recovery offset 0x00004f400000, size 0x000001800000
[ 3.924438@0] meson-mmc: [mmcblk0p07] misc offset 0x000051400000, size 0x000000800000
[ 3.924584@0] meson-mmc: [mmcblk0p08] dtbo offset 0x000052400000, size 0x000000800000
[ 3.924738@0] meson-mmc: [mmcblk0p09] cri_data offset 0x000053400000, size 0x000000800000
[ 3.924881@0] meson-mmc: [mmcblk0p10] param offset 0x000054400000, size 0x000001000000
[ 3.925032@0] meson-mmc: [mmcblk0p11] boot offset 0x000055c00000, size 0x000001000000
[ 3.925173@0] meson-mmc: [mmcblk0p12] rsv offset 0x000057400000, size 0x000001000000
[ 3.925331@0] meson-mmc: [mmcblk0p13] metadata offset 0x000058c00000, size 0x000001000000
[ 3.925475@0] meson-mmc: [mmcblk0p14] vbmeta offset 0x00005a400000, size 0x000000200000
[ 3.925610@0] meson-mmc: [mmcblk0p15] tee offset 0x00005ae00000, size 0x000002000000
[ 3.925783@0] meson-mmc: [mmcblk0p16] vendor offset 0x00005d600000, size 0x000046000000
[ 3.925920@0] meson-mmc: [mmcblk0p17] odm offset 0x0000a3e00000, size 0x000008000000
[ 3.926071@0] meson-mmc: [mmcblk0p18] system offset 0x0000ac600000, size 0x000050000000
[ 3.926202@0] meson-mmc: [mmcblk0p19] product offset 0x0000fce00000, size 0x000008000000
[ 3.926335@0] meson-mmc: [mmcblk0p20] data offset 0x000105600000, size 0x000d8a200000
[ 3.926354@0] card key: card_blk_probe.
[ 3.926359@0] emmc_key_init:183 emmc key lba_start:0x12020,lba_end:0x12220
[ 3.926363@0] emmc key: emmc_key_init:205 ok.
[ 3.928301@0] meson-mmc: amlmmc_dtb_init: register dtb chardev
[ 3.928302@0] meson-mmc: calc 5e40354d, store 5e40354d
[ 3.930105@0] meson-mmc: calc 5e40354d, store 5e40354d
[ 3.930108@0] meson-mmc: total valid 2
[ 3.930371@0] meson-mmc: amlmmc_dtb_init: register dtb chardev OK
[ 3.930371@0] meson-mmc: Exit aml_emmc_partition_ops OK.
[ 11.479639@0] vout: aml_tvout_mode_work: monitor_timeout
[ 62.487640@0] fb: mem_free_work, free memory: addr:800000
|
上一篇： TranSpeed X4、X4S补丁版本11.15.1，适用于HK1 RBOX X4.下一篇： 适用于HK1 RBOX S905 X4盒子的ATV11.15.1（20230811）
|
网站导航
发表于 2023-8-6 13:07
收藏
淘帖
顶一个
踩
提升卡
置顶卡
变色卡
千斤顶
znds.com 