四川高安TY1208-Z Uboot循环跑码

oaknehc · 发表于 2023-7-17 18:42

开机总是重复这一段。指示灯双红，两个USB口不供电，SD卡也失效。盒子也是收来了，故障真是五花八门，有没有大神知道怎么破。
BL2 Built : 14:55:32, Mar 24 2017.
gxl g4bbe26f - shuiyuan.huang@droid10-sz

Board ID = 7, adc=567
set vcck to 1070 mv
set vddee to 1070 mv
CPU clk: 1200MHz
2layers board, use ddr_set[0]
DQS-corr enabled
DDR scramble enabled
Pull down ddr cke
DDR3 chl: Rank0+1 @ 792MHz - FAIL
DDR3 chl: Rank0 @ 792MHz - PASS
Rank0: 128MB(auto)-2T-11
DataBus test pass!
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
GXL:BL1:9ac50e:a1974b;FEAT:BDFD31BC;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 94387

BL2 Built : 14:55:32, Mar 24 2017.
gxl g4bbe26f - shuiyuan.huang@droid10-sz

Board ID = 7, adc=567
set vcck to 1070 mv
set vddee to 1070 mv
CPU clk: 1200MHz
2layers board, use ddr_set[0]
DQS-corr enabled
DDR scramble enabled
Pull down ddr cke
DDR3 chl: Rank0+1 @ 792MHz - FAIL
DDR3 chl: Rank0 @ 792MHz - PASS
Rank0: 128MB(auto)-2T-11
DataBus test pass!
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
GXL:BL1:9ac50e:a1974b;FEAT:BDFD31BC;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 94375

BL2 Built : 14:55:32, Mar 24 2017.
gxl g4bbe26f - shuiyuan.huang@droid10-sz

Board ID = 7, adc=567
set vcck to 1070 mv
set vddee to 1070 mv
CPU clk: 1200MHz
2layers board, use ddr_set[0]
DQS-corr enabled
DDR scramble enabled
Pull down ddr cke
DDR3 chl: Rank0+1 @ 792MHz - FAIL
DDR3 chl: Rank0 @ 792MHz - PASS
Rank0: 128MB(auto)-2T-11
DataBus test pass!
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000

oaknehc · 发表于 2023-7-17 18:58

短接4R12 从SD卡引导也是一样

Board ID = 7, adc=560
set vcck to 1070 mv
set vddee to 1070 mv
CPU clk: 1200MHz
2layers board, use ddr_set[0]
DQS-corr enabled
DDR scramble enabled
Pull down ddr cke
DDR3 chl: Rank0+1 @ 792MHz - FAIL
DDR3 chl: Rank0 @ 792MHz - PASS
Rank0: 128MB(auto)-2T-11
DataBus test pass!
AddrBus test pass!
Load fip header from SD, src: 0x0000c200, des: 0x01400000, size: 0x00004000
GXL:BL1:9ac50e:a1974b;FEAT:BDFD31BC;POC:3;RCY:0;EMMC:800;NAND:81;SD:0;READ:0;0.0;CHK:0;
no sdio debug board detected
TE: 168306

BL2 Built : 14:55:32, Mar 24 2017.
gxl g4bbe26f - shuiyuan.huang@droid10-sz

Board ID = 7, adc=560
set vcck to 1070 mv
set vddee to 1070 mv
CPU clk: 1200MHz
2layers board, use ddr_set[0]
DQS-corr enabled
DDR scramble enabled
Pull down ddr cke
DDR3 chl: Rank0+1 @ 792MHz - FAIL
DDR3 chl: Rank0 @ 792MHz - PASS
Rank0: 128MB(auto)-2T-11
DataBus test pass!
AddrBus test pass!
Load fip header from SD, src: 0x0000c200, des: 0x01400000, size: 0x00004000
GXL:BL1:9ac50e:a1974b;FEAT:BDFD31BC;POC:3;RCY:0;EMMC:800;NAND:81;SD:0;READ:0;0.0;CHK:0;
no sdio debug board detected
TE: 168285

BL2 Built : 14:55:32, Mar 24 2017.
gxl g4bbe26f - shuiyuan.huang@droid10-sz

Board ID = 7, adc=560
set vcck to 1070 mv
set vddee to 1070 mv
CPU clk: 1200MHz
2layers board, use ddr_set[0]
DQS-corr enabled
DDR scramble enabled
Pull down ddr cke
DDR3 chl: Rank0+1 @ 792MHz - FAIL
DDR3 chl: Rank0 @ 792MHz - PASS
Rank0: 128MB(auto)-2T-11
DataBus test pass!
AddrBus test pass!
Load fip header from SD, src: 0x0000c200, des: 0x01400000, size: 0x00004000
GXL:BL1:9ac50e:a1974b;FEAT:BDFD31BC;POC:3;RCY:0;EMMC:800;NAND:81;SD:0;READ:0;0.0;CHK:0;
no sdio debug board detected
TE: 168296

BL2 Built : 14:55:32, Mar 24 2017.
gxl g4bbe26f - shuiyuan.huang@droid10-sz

oaknehc · 发表于 2023-7-17 19:42

关机一会再开机能小概率能往下跑码跑到加载kernel又中断了
Net: dwmac.c9410000
wipe_data=successful
wipe_cache=successful
upgrade_step=2
Err imgread(L340):Logo header err.
There is no valid bmp file at the given address
[CANVAS]addr=0x3d800000 width=3840, height=2160
There is no valid bmp file at the given address
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0
[KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet
rebootmode=cold_boot
Hit any key to stop autoboot:  0
[imgread]szTimeStamp[2018062815050115]
[imgread]secureKernelImgSz=0x93f000
aml log : R1024 check pass!
aml log : R1024 check pass!
aml log : R1024 check pass!
ee_gate_off ...
## Booting Android Image at 0x01080000 ...
reloc_addr =33f04b50
copy done
   Amlogic multi-dtb tool
   Single dtb detected
load dtb from 0x1000000 ......
Uncompressing Kernel Image ... OK
kernel loaded at 0x01080000, end = 0x01f81a50
Loading Ramdisk to 33c4c000, end 33ed5800 ... OK
Loading Device Tree to 000000001fff3000, end 000000001ffff959 ... OK
signature:
fdt_instaboot: get header err

Starting kernel ...

uboot time: 2618540 us
[ 0.000000@0] Initializing cgroup subsys cpu
[ 0.000000@0] Initializing cgroup subsys cpuacct
[ 0.000000@0] Linux version 3.14.29 (zhangcc@hengguott-PowerEdge-R920) (gcc version 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.09 - Linaro GCC 4.9-2014.09) ) #1 SMP PREEMPT Thu Jun 28 14:36:01 CST 2018
[ 0.000000@0] CPU: ARMv71 Processor [410fd034] revision 4
[ 0.000000@0] bootconsole [earlycon0] enabled
get_dvfs_info 0007
INFO: HDCP22 key read fail!
INFO: p1d 0
INFO: pd1 0

oaknehc · 发表于 2023-7-17 19:43

本帖最后由 oaknehc 于 2023-7-17 22:46 编辑

小概率能跑到kernel然后又中断了，硬件电路是不是有故障了呢？
Net: dwmac.c9410000
wipe_data=successful
wipe_cache=successful
upgrade_step=2
Err imgread(L340):Logo header err.
There is no valid bmp file at the given address
[CANVAS]addr=0x3d800000 width=3840, height=2160
There is no valid bmp file at the given address
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0
[KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet
rebootmode=cold_boot
Hit any key to stop autoboot:  0
[imgread]szTimeStamp[2018062815050115]
[imgread]secureKernelImgSz=0x93f000
aml log : R1024 check pass!
aml log : R1024 check pass!
aml log : R1024 check pass!
ee_gate_off ...
## Booting Android Image at 0x01080000 ...
reloc_addr =33f04b50
copy done
   Amlogic multi-dtb tool
   Single dtb detected
load dtb from 0x1000000 ......
Uncompressing Kernel Image ... OK
kernel loaded at 0x01080000, end = 0x01f81a50
Loading Ramdisk to 33c4c000, end 33ed5800 ... OK
Loading Device Tree to 000000001fff3000, end 000000001ffff959 ... OK
signature:
fdt_instaboot: get header err

Starting kernel ...

uboot time: 2618540 us
[ 0.000000@0] Initializing cgroup subsys cpu
[ 0.000000@0] Initializing cgroup subsys cpuacct
[ 0.000000@0] Linux version 3.14.29 (zhangcc@hengguott-PowerEdge-R920) (gcc version 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.09 - Linaro GCC 4.9-2014.09) ) #1 SMP PREEMPT Thu Jun 28 14:36:01 CST 2018
[ 0.000000@0] CPU: ARMv71 Processor [410fd034] revision 4
[ 0.000000@0] bootconsole [earlycon0] enabled
get_dvfs_info 0007
INFO: HDCP22 key read fail!
INFO: p1d 0
INFO: pd1 0

oaknehc · 发表于 2023-7-18 15:06

怀疑DDR跟FLASH 某一个有问题了？

oaknehc · 发表于 2023-7-18 15:07

有没有知道高安版本是否对USB口有限流指令？

oaknehc · 发表于 2023-7-21 08:28

有没有人知道哇

oaknehc · 发表于 2023-7-21 21:08

????????

oaknehc · 发表于 2023-7-22 17:58

EMMC是不是坏了

royalwei · 发表于 2023-12-18 12:39

代码看内存正常，应该emmc挂了

› 你问我答 / 玩机教程 / 固件 › ZNDS刷机/救砖

四川高安TY1208-Z Uboot循环跑码

四川高安TY1208-Z Uboot循环跑码

浏览过的版块