B860AV2.1-U刷机问题

DestoryG · 发表于 2023-2-6 23:11

这玩意但凡线刷个不是官改的固件都死给你看，都是uboot/获取返回/diskinitial命令出错，怎么搞啊
TTL日志：

U-Boot 2015.01-g7ec51b9-dirty (Nov 24 2016 - 21:44:53)
DRAM: 1 GiB
Starting uboot
gpio: pin GPIOCLK_1 (gpio 99) value is 1
gpio: pin GPIOAO_6 (gpio 106) value is 1
[MSG]MMC init in usb
aml_priv->desc_buf = 0x0000000037ec6db0
aml_priv->desc_buf = 0x0000000037ec8f40
SDIO Port B: 0, SDIO Port C: 1
Try USB burn
Set Addr 19
Get DT cfg
Get DT cfg
Get DT cfg
Get DT cfg
Get DT cfg
set CFG
ID[16]
tplcmd[ echo 12345]
12345
[MSG]ret = 0
[info]success
BULKcmd[ low_power]
[info]success
ID[16]
tplcmd[ download mem dtb normal 256000]
[MSG]Down(mem) part(dtb) sz(0x3e800) fmt(normal)
[MSG]totalSlotNum = 0, nextWriteBackSlot 4
[info]success
[MSG]Burn Start...
[MSG]load dt.img to 0x0000000001000000, sz=0x3e800
[MSG]Burn complete
BULKcmd[download get_status]
[info]success
BULKcmd[disk_initial 1]
Amlogic multi-dtb tool
Multi dtb detected
checkhw - ADC value:0x8
Multi dtb tool version: v2 .
Support 7 dtbs.
aml_dt soc: gxl platform: p211 variant: 1g
dtb 0 soc: gxb plat: p200 vari: 1g
dtb 1 soc: gxb plat: p200 vari: 2g
dtb 2 soc: gxl plat: p211 vari: 1g
dtb 3 soc: gxl plat: p211 vari: 2g
dtb 4 soc: gxl plat: p215 vari: 1g
dtb 5 soc: gxl plat: p215 vari: 2g
dtb 6 soc: gxl plat: p215hc100 vari: 2g
Find match dtb: 2
start dts,buffer=0000000001000000,dt_addr=0000000001011800
parts: 11
00: conf 0000000000400000 1
01: logo 0000000002000000 1
02: recovery 0000000002000000 1
03: rsv 0000000000800000 1
04: tee 0000000000800000 1
05: crypt 0000000002000000 1
06: misc 0000000002000000 1
07: boot 0000000002000000 1
08: system 0000000040000000 1
09: cache 0000000030000000 2
10: data ffffffffffffffff 4
emmc/sd response timeout, cmd = 8
emmc/sd response timeout, cmd = 55
emmc/sd response timeout, cmd = 1
card out
emmc/sd response timeout, cmd = 8
emmc/sd response timeout, cmd = 55
emmc/sd response timeout, cmd = 1
amlmmc cmd failed
store - STORE sub-system
Usage:
store store init flag
store read name addr off|partition size
read 'size' bytes starting at offset 'off'
to/from memory address 'addr', skipping bad blocks.
store write name addr off|partition size
write 'size' bytes starting at offset 'off'
to/from memory address 'addr', skipping bad blocks.
store rom_write add off size.
write uboot to the boot device
store erase boot/data:
erase the area which is uboot or data
store erase dtb
store erase key
store rom_protect on/off
store scrub off|partition size
scrub the area from offset and size
store dtb iread/read/write addr <size>
read/write dtb, size is optional
store key read/write addr <size>
read/write key, size is optional
cmd [store] init failed
[info]failed:

复制代码

0ffff · 发表于 2023-2-7 09:37

不懂，毕业之后就再也没接触过编程了

DestoryG · 发表于 2023-2-7 10:41

QQ846162.4 发表于 2023-2-7 08:59
砖

没砖，官改固件还是可以刷进去的

› 运营商IPTV / 有线电视 / 广电机顶盒 › 中兴机顶盒

B860AV2.1-U刷机问题

B860AV2.1-U刷机问题

相关帖子