巧虎定制百事通盒子型号R1200能刷机吗

土著古 · 发表于 2022-7-30 19:31

本帖最后由肖元元于 2022-7-30 20:04 编辑

巧虎定制百事通盒子型号R1200能刷机吗

橙子的甜 · 发表于 2022-7-30 20:05

这种刷机比较难，要不楼主直接考虑当贝以旧换新换成当贝超级盒子H2吧，操作简单，系统流畅，而且不用刷机，当贝以旧换新链接：https://shop.dangbei.com/huanxin

月光※傾城 · 发表于 2022-7-30 20:32

主板正反面和CPU型号拍照片

土著古 · 发表于 2022-7-31 19:59

月光※傾城发表于 2022-7-30 20:32
主板正反面和CPU型号拍照片

2018年买的,有点旧

土著古 · 发表于 2022-7-31 20:00

橙子的甜发表于 2022-7-30 20:05
这种刷机比较难，要不楼主直接考虑当贝以旧换新换成当贝超级盒子H2吧，操作简单，系统流畅，而且不用刷机， ...

当贝也出电视盒子了?

rk_2010 · 发表于 2023-9-18 16:37

月光※傾城发表于 2022-7-30 20:32
主板正反面和CPU型号拍照片

手上有个巧虎小红盒，型号：R1200。原系统需要巧虎账号登录。问了巧虎官方客户说已被别人绑定，我不能使用。只能刷机了，拆开一开，具然焊了串口线。只是比常规的串口线小且细，接上去容易掉。折腾了好一会，才看到ttl跑码。
GXL:BL1:9ac50e:bb16dc;FEAT:ADFC318C:0;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 142278

BL2 Built : 14:57:36, Nov  4 2016.
gxl g5990442 - xiaobo.gu@droid05

set vcck to 1070 mv
set vddee to 1070 mv
Board ID = 7, adc=544
CPU clk: 1200MHz
2layers board, use ddr_set[0]
DDR chl: Rank0+1 @ 792MHz - FAIL
DDR chl: Rank0 @ 792MHz - PASS
DQS-corr enabled
DDR scramble enabled
Rank0: 1024MB(auto)-2T-11
DataBus test pass!
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x01100000, size: 0x00007400
Load bl301 from eMMC, src: 0x00018200, des: 0x01200000, size: 0x00002200
Load bl31 from eMMC, src: 0x0001c200, des: 0x10100000, size: 0x00019400
Load bl33 from eMMC, src: 0x00038200, des: 0x01000000, size: 0x00084000
NOTICE:  BL3-1: v1.0(debug):959fdf0
NOTICE:  BL3-1: Built : 15:01:44, Dec 29 2016
aml log : bl31 normal boot !
[Image: gxl_v1.1.3088-142d621 2016-11-14 18:19:22 yun.cai@droid06]
bl30: check_permit, count is 1
bl30: check_permit: ok!
chipid: 0 0 3 c c 0 56 b3 80 a0 0 e4 not ES chip
efuse init ops = e4
efuse init hdcp = c, cf9=7
[0.424321 Inits done]
sINFeOc:u r e tBaLs3k- 1s:t aIrnti!ti
alizing runthiimgeh  steavices
WARNING: No OPTEE provided by BL2 boot loader
ERROR: Error initializing runtime service opteed_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x1000000
INFO: BL3-1: Next image spsr = 0x3c9

U-Boot 2015.01-g2875563-dirty (Jun 21 2019 - 04:42:43)

DRAM:  1 GiB
Relocation Offset is: 36eef000
gpio: pin GPIODV_24 (gpio 43) value is 1
mwm 0xc8837004:[0x aa203] with [0x ea203] ok
mwm 0xc883700c:[0x 3e3b744] with [0x 3e3b764] ok
mwm 0xc8837010:[0x c0101] with [0x c8101] ok
mwm 0xc8837010:[0x c8101] with [0x  128101] ok
register usb cfg[0][1] = 0000000037f632f8
[CANVAS]canvas init
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
MMC: aml_priv->desc_buf = 0x0000000033edfac0
aml_priv->desc_buf = 0x0000000033ee1de0
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
[mmc_startup] mmc refix success
[mmc_init] mmc init success
mmc read lba=0x14000, blocks=0x400
   Amlogic multi-dtb tool
   Multi dtb detected
   2layers board, board id use 7
   Multi dtb tool version: v2 .
   Support 6 dtbs.
      aml_dt soc: gxl platform: p211 variant: 1g
      dtb 0 soc: gxbb plat: p201 vari: 1g
      dtb 1 soc: gxbb plat: p201 vari: 2g
      dtb 2 soc: gxl plat: p211 vari: 1g
      dtb 3 soc: gxl plat: p211 vari: 2g
      dtb 4 soc: gxl plat: p215 vari: 1g
      dtb 5 soc: gxl plat: p215 vari: 2g
   Find match dtb: 2
start dts,buffer=0000000033ee4630,dt_addr=0000000033ef5e30
parts: 12
00:    logo 0000000002000000 1
01:  recovery 0000000002000000 1
02:    rsv 0000000000800000 1
03:    tee 0000000000800000 1
04:    crypt 0000000002000000 1
05:    misc 0000000002000000 1
06: instaboot 0000000020000000 1
07:    boot 0000000002000000 1
08: system 0000000040000000 1
09:    cache 0000000020000000 2
10:cus_config 0000000020000000 2
11:    data ffffffffffffffff 4
get_dtb_struct: Get emmc dtb OK!
overide_emmc_partition_table: overide cache
[mmc_get_partition_table] skip partition cache.
Partition table get from SPL is :
      name                      offset             size             flag
===================================================================================
0: bootloader                      0          400000                0
1: reserved                   2400000          4000000                0
2: cache                      6c00000       20000000                2
3: env                      27400000          800000                0
4: logo                      28400000          2000000                1
5: recovery                   2ac00000          2000000                1
6: rsv                      2d400000          800000                1
7: tee                      2e400000          800000                1
8: crypt                      2f400000          2000000                1
9: misc                      31c00000          2000000                1
  10: instaboot                34400000       20000000                1
  11: boot                      54c00000          2000000                1
  12: system                   57400000       40000000                1
  13: cus_config                97c00000       20000000                2
  14: data                      b8400000       119c00000                4
mmc read lba=0x12000, blocks=0x2
mmc read lba=0x12002, blocks=0x2
mmc_read_partition_tbl: mmc read partition OK!
eMMC/TSD partition table have been checked OK!
mmc env offset: 0x27400000
In: serial
Out: serial
Err: serial
board id is : 7
hpd_state=0
cvbs performance type = 7, table = 1
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
read emmc dtb
   Amlogic multi-dtb tool
   Multi dtb detected
   2layers board, board id use 7
   Multi dtb tool version: v2 .
   Support 6 dtbs.
      aml_dt soc: gxl platform: p211 variant: 1g
      dtb 0 soc: gxbb plat: p201 vari: 1g
      dtb 1 soc: gxbb plat: p201 vari: 2g
      dtb 2 soc: gxl plat: p211 vari: 1g
      dtb 3 soc: gxl plat: p211 vari: 2g
      dtb 4 soc: gxl plat: p215 vari: 1g
      dtb 5 soc: gxl plat: p215 vari: 2g
   Find match dtb: 2
Net: dwmac.c9410000
Error: dwmac.c9410000 address not set.

wipe_data=successfulSecd
wipe_cache=successful
bmp pixel: 16
[CANVAS]addr=0x3d800000 width=2560, height=1440
upgrade_step=2
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0
[KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet
gpio: pin GPIOAO_2 (gpio 102) value is 1
key1 = b649ff00
key2 = b649fd01
key3 = 728ddd22
time_out = 30d40
ir init
irkey - irkey key_value1 key_value2 key_value3 time_value

Usage:
irkey
rebootmode=cold_boot
Hit any key to stop autoboot:  0
ee_gate_off ...
## Booting Android Image at 0x01080000 ...
reloc_addr =33f0c210
copy done
   Amlogic multi-dtb tool
   Single dtb detected
load dtb from 0x1000000 ......
Uncompressing Kernel Image ... OK
kernel loaded at 0x01080000, end = 0x01ff2c18
Loading Ramdisk to 33c57000, end 33edcb07 ... OK
Loading Device Tree to 000000001fff3000, end 000000001ffff02a ... OK
signature:
fdt_instaboot: get header err

Starting kernel ...

uboot time: 2054228 us
[ 0.000000@0] Initializing cgroup subsys cpu
[ 0.000000@0] Initializing cgroup subsys cpuacct
[ 0.000000@0] Linux version 3.14.29-gc47bd4e5ae2-dirty (colin@ter) (gcc version 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.09 - Linaro GCC 4.9-2014.09) ) #4 SMP PREEMPT Thu Dec 12 03:10:25 EST 2019
[ 0.000000@0] CPU: armv71 Processor [410fd034] revision 4
[ 0.000000@0] bootconsole [earlycon0] enabled
get_dvfs_info 0007
INFO: HDCP22 key read fail!
INFO: p1d 0
INFO: pd1 0
root@p201_iptv:/ #

CPU是晶晨的S905M。不知道能不能刷机？用哪个固件刷机？请大佬帮忙指导一下。

25252245 · 发表于 2023-9-19 15:16

谁搞定这个了

liuspcn · 发表于 2023-10-21 18:54

那位大神的R1200已经ttl了，能不能提取一下里面的uboot？我需要，我想我离刷成只有一步之遥了。

liuspcn · 发表于 2023-10-23 10:01

我的是R1200-C的型号芯片是S905L3的，现在可以刷当贝精简桌面包，使用遥控器有个问题（关机后，遥控器不能开机，值能拔插一下电源让其开机），其他正常。哪位能把机顶盒中的boot.img 提取出来给我试试，能不能解决遥控器不能开机的问题。如果实现完美刷机，我就发个帖子讲一下。

liuspcn · 发表于 2023-10-23 10:05

我机顶盒里的boot.img被我换过了，当时没有备份。

› 你问我答 / 玩机教程 / 固件 › 你问我答

巧虎定制百事通盒子型号R1200能刷机吗

巧虎定制百事通盒子型号R1200能刷机吗

相关帖子