▒@@▒▒GXL:BL1:9ac50e:bb16dc;FEAT:BDFD31BC:0;POC:3;RCY:0;EMMC:800;NAND:0;READ:0;0.0;0.0;CHK:0;
TE: 137007
BL2 Built : 14:48:45, Sep 26 2018.
gxl g6d68897 - yao.zhang@droid07
Board ID = 8, adc=624
set vcck to 1070 mv
set vddee to 1070 mv
CPU clk: 1200MHz
LPower:
DDR3 chl: Rank0+1 @ 792MHz - FAIL
DDR3 chl: Rank0 @ 792MHz
bist_test rank: 0 23 00 46 3c 1b 5e 1f 00 3f 44 23 65 20 00 40 42 23 61 1c 00 38 42 22 62 601 - PASS
Rank0: 1024MB(auto)-2T-11
AddrBus test pass!
NAND init
Load fip header from NAND, src: 0x0000c000, des: 0x01400000, size: 0x00004000
aml log : R2048 check pass!
New fip structure!
Load bl30 from NAND, src: 0x00010000, des: 0x01700000, size: 0x00007600
aml log : R2048 check pass!
Load bl301 from NAND, src: 0x00018000, des: 0x01700000, size: 0x00002600
aml log : R2048 check pass!
Load bl31 from NAND, src: 0x0001c000, des: 0x01700000, size: 0x00019600
aml log : R2048 check pass!
Load bl33 from NAND, src: 0x00038000, des: 0x01700000, size: 0x00080600
aml log : R2048 check pass!
NOTICE: BL3-1: v1.0(debug):f10670a
NOTICE: BL3-1: Built : 16:48:58, Nov 14 2018
NOTICE: BL31: GXL secure boot!
NOTICE: BL31: BL33 decompress pass
[Image: gxl_v1.1.3101-a78fa1e 2018-06-04 16:24:21 huan.biao@droid12]
efuse init ops = e4
efuse init hdcp = c, cf9=7
bl30: check_permit, count is 1
bl30: check_permit: ok!
chipid: 0 0 7 1c c 0 30 b3 98 a0 0 e4 not ES chip
[1.248833 Inits done]
INFO: BL3-1: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader
ERROR: Error initializing runtime service opteed_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x1000000
INFO: BL3-1: Next image spsr = 0x3c9
U-Boot 2015.01-g49ae8bc-dirty (Dec 15 2018 - 12:19:02)
DRAM: 1 GiB
reboot_mode=cold_boot
init - init amlnand_phy here
chipinfo - show aml chip information
device[dev] - show or set current device
partition* [part] - show or set current partition
plane[dev] - show or set current plane mode
read - addr off|partition size
write - addr off|partition size
read/write 'size' bytes starting at offset 'off'
to/from memory address 'addr', skipping bad blocks.
erase[clean|whole][off size] - erase 'size' bytes from
offset 'off' (entire device if not specified)
dump addr off
show the raw data to addr at offset off
read_byte - addr off|partition size
write_byte - addr off|partition size
read_byte/write_byte 'size' bytes starting at offset 'off'
to/from memory address 'addr', skipping bad blocks.
deVRead - addr off|partition size
devwrite - addr off|partition size
read/write 'size' bytes starting at offset 'off' in device[dev]
to/from memory address 'addr', skipping bad blocks.
deverase[whole][off size] - erase 'size' bytes from
offset 'off' (entire device if not specified) in device[dev]
markbad addr - mark block bad at addr
mark_reserved reserved_blk_NO -mark reserved_blk_NO bad
ldevice[dev] - show/get nftl(logic) device by name
rom_read/write addr off cnt - read/write uboot.
boot - show boot flagdtb_read/write addr cnt - read/write dtd.
dtb_erase - erase dtb!
key_read/write addr cnt - read/write dtd.
key_erase - erase keys!
scrub3d - Erase (scrub) nand in SLC/MLC mode. switch back to MLC!
store init flag
store read name addr off|partition size
read 'size' bytes starting at offset 'off'
to/from memory address 'addr', skipping bad blocks.
store write name addr off|partition size
write 'size' bytes starting at offset 'off'
to/from memory address 'addr', skipping bad blocks.
store rom_write add off size.
write uboot to the boot device
store erase boot/data:
erase the area which is uboot or data
store erase partition <partition_name>:
erase the area which partition in u-boot
store erase dtb
store erase key
store disprotect key
store rom_protect on/off
store scrub off|partition size
scrub the area from offset and size
store dtb iread/read/write addr <size>
read/write dtb, size is optional
store key read/write addr <size>
read/write key, size is optional
store mbr addr
update mbr/partition table by dtb
No ethernet found.
init - init amlnand_phy here
chipinfo - show aml chip information
device[dev] - show or set current device
partition* [part] - show or set current partition
plane[dev] - show or set current plane mode
read - addr off|partition size
write - addr off|partition size
read/write 'size' bytes starting at offset 'off'
to/from memory address 'addr', skipping bad blocks.
erase[clean|whole][off size] - erase 'size' bytes from
offset 'off' (entire device if not specified)
dump addr off
show the raw data to addr at offset off
read_byte - addr off|partition size
write_byte - addr off|partition size
read_byte/write_byte 'size' bytes starting at offset 'off'
to/from memory address 'addr', skipping bad blocks.
devread - addr off|partition size
devwrite - addr off|partition size
read/write 'size' bytes starting at offset 'off' in device[dev]
to/from memory address 'addr', skipping bad blocks.
deverase[whole][off size] - erase 'size' bytes from
offset 'off' (entire device if not specified) in device[dev]
markbad addr - mark block bad at addr
mark_reserved reserved_blk_NO -mark reserved_blk_NO bad
ldevice[dev] - show/get nftl(logic) device by name
rom_read/write addr off cnt - read/write uboot.
boot - show boot flagdtb_read/write addr cnt - read/write dtd.
dtb_erase - erase dtb!
key_read/write addr cnt - read/write dtd.
key_erase - erase keys!
scrub3d - Erase (scrub) nand in SLC/MLC mode. switch back to MLC!
store init flag
store read name addr off|partition size
read 'size' bytes starting at offset 'off'
to/from memory address 'addr', skipping bad blocks.
store write name addr off|partition size
write 'size' bytes starting at offset 'off'
to/from memory address 'addr', skipping bad blocks.
store rom_write add off size.
write uboot to the boot device
store erase boot/data:
erase the area which is uboot or data
store erase partition <partition_name>:
erase the area which partition in u-boot
store erase dtb
store erase key
store disprotect key
store rom_protect on/off
store scrub off|partition size
scrub the area from offset and size
store dtb iread/read/write addr <size>
read/write dtb, size is optional
store key read/write addr <size>
read/write key, size is optional
store mbr addr
update mbr/partition table by dtb
set osd_size 1080p
bootmode:NORM
init - init amlnand_phy here
chipinfo - show aml chip information
device[dev] - show or set current device
partition* [part] - show or set current partition
plane[dev] - show or set current plane mode
read - addr off|partition size
write - addr off|partition size
read/write 'size' bytes starting at offset 'off'
to/from memory address 'addr', skipping bad blocks.
erase[clean|whole][off size] - erase 'size' bytes from
offset 'off' (entire device if not specified)
dump addr off
show the raw data to addr at offset off
read_byte - addr off|partition size
write_byte - addr off|partition size
read_byte/write_byte 'size' bytes starting at offset 'off'
to/from memory address 'addr', skipping bad blocks.
devread - addr off|partition size
devwrite - addr off|partition size
read/write 'size' bytes starting at offset 'off' in device[dev]
to/from memory address 'addr', skipping bad blocks.
deverase[whole][off size] - erase 'size' bytes from
offset 'off' (entire device if not specified) in device[dev]
markbad addr - mark block bad at addr
mark_reserved reserved_blk_NO -mark reserved_blk_NO bad
ldevice[dev] - show/get nftl(logic) device by name
rom_read/write addr off cnt - read/write uboot.
boot - show boot flagdtb_read/write addr cnt - read/write dtd.
dtb_erase - erase dtb!
key_read/write addr cnt - read/write dtd.
key_erase - erase keys!
scrub3d - Erase (scrub) nand in SLC/MLC mode. switch back to MLC!
boot system norm failed, try boot safe!
init - init amlnand_phy here
chipinfo - show aml chip information
device[dev] - show or set current device
partition* [part] - show or set current partition
plane[dev] - show or set current plane mode
read - addr off|partition size
write - addr off|partition size
read/write 'size' bytes starting at offset 'off'
to/from memory address 'addr', skipping bad blocks.
erase[clean|whole][off size] - erase 'size' bytes from
offset 'off' (entire device if not specified)
dump addr off
show the raw data to addr at offset off
read_byte - addr off|partition size
write_byte - addr off|partition size
read_byte/write_byte 'size' bytes starting at offset 'off'
to/from memory address 'addr', skipping bad blocks.
devread - addr off|partition size
devwrite - addr off|partition size
read/write 'size' bytes starting at offset 'off' in device[dev]
to/from memory address 'addr', skipping bad blocks.
deverase[whole][off size] - erase 'size' bytes from
offset 'off' (entire device if not specified) in device[dev]
markbad addr - mark block bad at addr
mark_reserved reserved_blk_NO -mark reserved_blk_NO bad
ldevice[dev] - show/get nftl(logic) device by name
rom_read/write addr off cnt - read/write uboot.
boot - show boot flagdtb_read/write addr cnt - read/write dtd.
dtb_erase - erase dtb!
key_read/write addr cnt - read/write dtd.
key_erase - erase keys!
scrub3d - Erase (scrub) nand in SLC/MLC mode. switch back to MLC!
gxl_p211_v1#
连上TTL能输入 怎么就砖？？？？请高人教我。
|
网站导航
发表于 2022-4-5 22:08
收藏
淘帖
顶一个
踩
提升卡
置顶卡
变色卡
千斤顶
楼主
/1 
znds.com 