TTL跑码但无法键入命令
TL1:BL:c60c31:eab5ad;FEAT:E0F97180:20282000;POC:F;RCY:0;EMMC:0;READ:0;p
bl2_stage_init1
L0:00000000
L1:00000700
L2:00008000
L3:00000000
S1:00000000
B2:20282000
B1:e0f97180
TE: 105388
BL2 Built : 18:07:14, Sep 27 2019. tl1 g8337d09 - niko.he@droid05-sz
Board ID = 2
Set cpu clk to 24M
Set clk81 to 24M
Use GP1_pll as DSU clk.
DSU clk: 1200 Mhz
CPU clk: 1200 MHz
Set clk81 to 166.6M
smccc: 0001e63c
eMMC boot @ 0
sw8 s
sd/emmc cmd 8 arg 0x00000000 status 01ff3000
DDR driver_vesion: LPDDR4_PHY_V_0_1_18 build time: Sep 27 2019 18:07:08
ddr id: 1
Load FIP HDR from eMMC, src: 0x00010200, des: 0xfffa0000, size: 0x00004000, part: 0
fw parse done
Load ddrfw from eMMC, src: 0x0004d200, des: 0xfffa0000, size: 0x0000b000, part: 0
Load ddrfw from eMMC, src: 0x0002f200, des: 0xfffa0000, size: 0x00002800, part: 0
PIEI prepare done
fastboot data load
00000000
emmc switch 1 ok
ddr saved addr:0000a000
Load ddr parameter from eMMC, src: 0x01400000, des: 0xfffa0000, size: 0x00001000, part: 0
00000000
emmc switch 0 ok
fastboot data verify
verify result: 0
enable_fast_boot
dmc_margin_rx==8 dmc_margin_tx==8 steps
DDR3 probe
ddr clk to 1008MHz
Load ddrfw from eMMC, src: 0x00026200, des: 0xfffa0000, size: 0x00009000, part: 0
Check phy result
INFO : End of initialization
INFO : Training has run successfully!
aml_ddr_fw_vesion: LPDDR4_PHY_V_0_1_18 build time: Aug 26 2019 16:27:12
DDR cs0 size: 1024MB
DDR cs1 size: 512MB
DMC_DDR_CTRL: 00200023DDR size: 1536MB
cs0 DataBus test pass
cs1 DataBus test pass
cs0 AddrBus test pass
cs1 AddrBus test pass
100bdlr_step_size ps== 438
result report
boot times 0Enable ddr reg access
00000000
emmc switch 3 ok
Authentication key not yet programmed
get rpmb counter error 0x00000007
00000000
emmc switch 0 ok
end bl2z2:
Load FIP HDR from eMMC, src: 0x00010200, des: 0x01700000, size: 0x00004000, part: 0
Load BL3X from eMMC, src: 0x00058200, des: 0x01748000, size: 0x000dc000, part: 0
0.0;M3 CHK:0;E30HDR
[Image: tl1_v1.1.3412-9e40837f5 2020-03-04 15:43:53 niko.he@droid05-sz]
OPS=0x09
ring efuse init
chipver efuse init
2e 0c 09 00 01 0b 09 00 00 19 39 38 47 50 56 50
GP_10: 0xfe0000ed
SD_12: 0xfe0000d2
GP_11: 0xfe0000c7
[0.021529 Inits done]
in timerled_task = 23
in timerled_task_audio = 23
secure task start!
high task start!
low task start!
run into bl31
NOTICE: BL31: v1.3(release):8b83a2e0b
NOTICE: BL31: Built : 18:19:22, Sep 27 2019
NOTICE: BL31: TL1 normal boot!
NOTICE: BL31: BL33 decompress pass
ERROR: Error initializing runtime service opteed_fast
U-Boot 2015.01-gf547139811 (Mar 17 2020 - 19:59:12)
DRAM: 1.5 GiB
Relocation Offset is: 56e38000
mmu cfg end: 0x60000000
mmu cfg end: 0x60000000
spi_post_bind(spicc): req_seq = 0
spi_post_bind(spifc): req_seq = 1
uboot time: 3267204 us
|
网站导航
楼主: xoukar123
[复制链接]
发表于 2022-11-25 08:42
znds.com 