ZNDS智能电视网 推荐当贝市场

TV应用下载 / 资源分享区

软件下载 | 游戏 | 讨论 | 社区App下载

综合交流 / 评测 / 活动区

交流区 | 测硬件 | 网站活动 | Z币中心

新手入门 / 进阶 / 社区互助

新手 | 你问我答 | 免费刷机救砖 | ROM固件

查看: 3487|回复: 3
[求助]

苏州云普的盒子,芯片是s905l-b现在变砖了ttl无法输入

[复制链接]
发表于 2022-1-14 20:29 | 显示全部楼层 |阅读模式
本帖最后由 魔刹石 于 2022-1-15 12:47 编辑

是一个苏州云普的盒子,芯片是s905l-b,现在已经是砖了,买了ttl线焊上,有输出,但是不能输入,请问这种情况是锁了ttl了吗 QQ截图20220114202329.png

上一篇:跪求中兴bv3140刷机包
下一篇:求助,中兴BV310刷机后出现1306
 楼主| 发表于 2022-1-14 20:30 | 显示全部楼层
GXL:BL1:9ac50e:bb16dc;FEAT:ADFD318C:0;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 45201

BL2 Built : 18:58:24, Oct 25 2016.
gxl gc9db010 - xiaobo.gu@droid05

set vcck to 1080 mv
set vddee to 1050 mv
Board ID = 7, adc=549
CPU clk: 1200MHz
2layers board, use ddr_set[0]
DDR chl: Rank0+1 @ 720MHz - FAIL
DDR chl: Rank0 @ 720MHz - PASS
DQS-corr enabled
DDR scramble enabled
Rank0: 1024MB(auto)-2T-11
DataBus test pass!
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
Load bl30 from eMMC, src: 0x00010200, des: 0x01100000, size: 0x00007400
Load bl301 from eMMC, src: 0x00018200, des: 0x01200000, size: 0x00002000
Load bl31 from eMMC, src: 0x0001c200, des: 0x10100000, size: 0x00019400
Load bl33 from eMMC, src: 0x00038200, des: 0x01000000, size: 0x000a6200
NOTICE:  BL3-1: v1.0(debug):959fdf0
NOTICE:  BL3-1: Built : 15:01:44, Dec 29 2016
aml log : bl31 normal boot !
[Image: gxl_v1.1.3086-872dec0 2016-09-21 21:56:30 xiaobo.gu@droid05]
bl30: check_permit, count is 1
bl30: check_permit: ok!
chipid: 0 0 3 c c 0 97 b3 80 a0 0 c4 not ES chip
efuse init ops = c4
efuse init hdcp = c, cf9=7
[0.354539 Inits done]
secIuNrFeO :t a s k  BsLt3a-r1t:! I
nitializing hriugnht itmaes ks rvices
WARNING: No OPTEE provided by BL2 boot loader
ERROR:   Error initializing runtime service opteed_fast
INFO:    BL3-1: Preparing for EL3 exit to normal world
INFO:    BL3-1: Next image address = 0x1000000
INFO:    BL3-1: Next image spsr = 0x3c9


U-Boot 2015.01-svn125577 (Mar 18 2017 - 21:47:22)

DRAM:  1 GiB
Relocation Offset is: 36ecf000
gpio: pin GPIODV_24 (gpio 43) value is 0
gpio: pin GPIOAO_3 (gpio 103) value is 1
mwm 0xc8837004:[0x   aa203] with [0x   ea203] ok
mwm 0xc883700c:[0x 3e3b744] with [0x 3e3b764] ok
mwm 0xc8837010:[0x   c0101] with [0x   c8101] ok
mwm 0xc8837010:[0x   c8101] with [0x  128101] ok
register usb cfg[0][1] = 0000000037f63db0
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
boot_device_flag : 1
Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
init bus_cycle=6, bus_timing=7, system=5.0ns
reset failed
get_chip_type and ret:fffffffe
get_chip_type and ret:fffffffe
chip detect failed and ret:fffffffe
nandphy_init failed and ret=0xfffffff1
MMC:   aml_priv->desc_buf = 0x0000000033ebfdb0
aml_priv->desc_buf = 0x0000000033ec20d0
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x1ff2800
emmc/sd response timeout, cmd55, status=0x1ff2800
[mmc_startup] mmc refix success
[mmc_init] mmc init success
overide_emmc_partition_table: overide cache
[mmc_get_partition_table] skip partition cache.
mmc read lba=0x12000, blocks=0x2
mmc read lba=0x12002, blocks=0x2
mmc_read_partition_tbl: mmc read partition OK!
eMMC/TSD partition table have been checked OK!
mmc env offset: 0x27400000
In:    serial
Out:   serial
Err:   serial
board id is : 7
hpd_state=0
cvbs performance type = 7, table = 1
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
read emmc dtb
dwmac.c9410000
Error: dwmac.c9410000 address not set.

wipe_data=successful
wipe_cache=successful
upgrade_step=2
reboot_mode=cold_boot
[CANVAS]canvas init
[CANVAS]addr=0x3d800000 width=5760, height=2160
[OSD]ERR: 24 bit/pixel mode, but BMP has 16 bit/pixel
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0
strlen = 32, error!
don't use random mac produce in uboot
IR init done!
gpio: pin GPIOH_6 (gpio 55) value is 1
Hit any key to stop autoboot:  0
ee_gate_off ...
## Booting Android Image at 0x01080000 ...
reloc_addr =33f44bc0
copy done
      Single dtb detected
load dtb from 0x1000000 ......
   Uncompressing Kernel Image ... OK
   kernel loaded at 0x01080000, end = 0x02033200
   Loading Ramdisk to 33c36000, end 33ebca00 ... OK
   Loading Device Tree to 000000001fff3000, end 000000001ffff3a1 ... OK

Starting kernel ...

uboot time: 1923089 us
[    0.000000@0] Initializing cgroup subsys cpu
[    0.000000@0] Initializing cgroup subsys cpuacct
[    0.000000@0] Linux version 3.14.29-svn125577 (chenshouhui@ubuntu) (gcc version 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.09 - Linaro GCC 4.9-2014.09) ) #1 SMP PREEMPT Sat Mar 18 22:16:52 HKT 2017
[    0.000000@0] CPU: armv71 Processor [410fd034] revision 4
[    0.000000@0] bootconsole [earlycon0] enabled
INFO:    HDCP22 key read fail!
INFO:    p1d 0
INFO:    pd1 0


这是所有跑的码
回复 支持 反对

使用道具 举报

 楼主| 发表于 2022-1-14 20:31 | 显示全部楼层
型号是bas8100,开机的时候按了回车和ctrl c,都不管用
回复 支持 反对

使用道具 举报

发表于 2022-1-15 12:49 | 显示全部楼层
变砖救不回来了可以考虑换一个新出的B3盒子哦,现在年货节有折扣,搭载了S922芯片
回复 支持 反对

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

关闭

站长推荐 上一条 /3 下一条

Archiver|新帖|标签|软件|Sitemap|ZNDS智能电视网 ( 浙ICP备14000780号-1 )

网络信息服务信用承诺书 | 增值电信业务经营许可证:浙B2-20150411 丨 浙公网安备 33010802006145号

浙网文(2016)6491-366号 | GMT+8, 2022-1-26 15:20 , Processed in 0.047309 second(s), 12 queries , MemCache On.

Powered by Discuz!

监督举报:report#znds.com (请将#替换为@)

© 2007-2022 ZNDS.Com

快速回复 返回顶部 返回列表