ZNDS智能电视网 推荐当贝市场

TV应用下载 / 资源分享区

软件下载 | 游戏 | 讨论 | 电视计算器

综合交流 / 评测 / 活动区

交流区 | 测硬件 | 网站活动 | Z币中心

新手入门 / 进阶 / 社区互助

新手 | 你问我答 | 免费刷机救砖 | ROM固件

查看: 11628|回复: 2
上一主题 下一主题
[求助]

8726mx命令怎么使用

[复制链接]
跳转到指定楼层
楼主
发表于 2021-3-30 19:26 | 只看该作者 回帖奖励 |倒序浏览 |阅读模式
本帖最后由 xhm789 于 2021-3-30 20:05 编辑

电视进不了桌面,想重u盘装。

EC3_MX_PANEL_V6 #?
?       - alias for 'help'
adtask  - Ad task when time is not boot time it will sleep
aeschk  - aeschk AES aLGorithm check sub-system
autoping- do auto ping test
autoscr - run script from memory
base    - print or set address offset
bdinfo  - print Board Info structure
bmp     - manipulate BMP image data
boardid_prefetch- boardid sub-system
boot    - SPI-NAND-COMPATIBLE
bootc   - boot boot.img form sdcard
bootm   - boot application image from memory
bootn   - boot uImage form nand
bootp   - boot image via network using BOOTP/TFTP protocol
bootr   - boot uImage_recovery from sdcard
bootu   - boot uImage form sdcard
burnuboot- burn uboot form sdcard
calc    - command for calculate
cbusreg - cbus register read/write
chpart  - change active partition
clear_rebootmode- clear rebootmode
clkmsr  - measure PLL clock
cmp     - memory compare
coninfo - print console devices and information
cp      - memory copy
crc32   - checksum calculation
data    - SPI-NAND-COMPATIBLE || SPI-NAND-EMMC-COMPATIBLE
dcache  - enable or disable data cache
defenv  - default environment
defenv_without- defenv without environment variables
dhcp    - boot image via network using DHCP/TFTP protocol
dummy   - Customer defined command!
echo    - echo args to console
editenv - edit environment variable
efuse   - efuse version/licence/mac/hdcp/usid read/write or dump raw efuse data commands
env     - environment handling commands
ethchk  - check ethernet status
ethdbg  - set ethernet debug level
ethmode - set ethernet mac mode
ethrst  - reset ethernet phy
exit    - exit script
ext2load- load binary file from a Ext2 filesystem
ext2ls  - list files in a directory (default /)
false   - do nothing, unsuccessfully
fatexist- find the file from a dos filesystem
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls   - list files in a directory (default /)
get_img_size- get img size and save the result as a environment variable
get_rebootmode- get reboot mode
go      - start application at address 'addr'
hdcp    - HDCP sub-system
help    - print command description/usage
icache  - enable or disable instruction cache
imxtract- extract a part of a multi-image
init_wifi- init wifi power
irkey   - irkey key_value time_value
itest   - return true/false on integer compare
kgdb    - enter gdb remote debug mode
ledflicker- Led flicker when there is no uImage or recovery can run
loadb   - load binary file over serial line (kermit mode)
loadenv - load environment at address 'addr'
loads   - load S-Record file over serial line
loadx   - load binary file over serial line (xmodem mode)
loady   - load binary file over serial line (ymodem mode)
loop    - infinite loop on address range
macreg  - ethernet mac register read/write/dump
md      - memory display
mdc_clk - do mdc clock
mm      - memory modify (auto-incrementing address)
mmc     - MMC sub system
mmcinfo - display MMC info
msleep  - delay execution for some time
mtdparts- define flash/nand partitions
mtest   - simple RAM read/write test
mw      - memory write (fill)
nand    - NAND sub-system
nboot   - boot from NAND device
netspd_f- enforce eth speed
nm      - memory modify (constant address)
phyreg  - ethernet phy register read/write/dump
ping    - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
rarpboot- boot image via network using RARP/TFTP protocol
reset   - Perform RESET of the CPU
run     - run commands in an environment variable
saradc  - saradc sub-system
saveenv - save environment variables to persistent storage
secukey - security KEY sub-system
setenv  - set environment variables
sf      - SPI flash sub-system
showvar - print local hushshell variables
sleep   - delay execution for some time
source  - run script from memory
ssecukey- NAND KEY sub-system
test    - minimal test like /bin/sh
tftpboot- boot image via network using TFTP protocol
tiny_usbtool- start tiny USB tool for PC burner
true    - do nothing, successfully
unpackimg- unpack imgpack to single
usb     - USB sub-system
usbbc   - test usb bc
usbboot - boot from USB device
usid_prefetch- usid sub-system
uuid_prefetch- uuid sub-system
version - print monitor, compiler and linker version
video   - video sub-system


8726(1).txt

10.22 KB, 下载次数: 2, 下载积分: 金币 -1


上一篇:江苏移动魔百和HG680-KA点击版本信息没用的前提...
下一篇:CM201-2 YS已成砖,如何救砖,请大侠指教!
沙发
 楼主| 发表于 2021-3-30 20:03 | 只看该作者

EC3_MX_PANEL_V6 #?
?       - alias for 'help'
adtask  - Ad task when time is not boot time it will sleep
aeschk  - aeschk AES algorithm check sub-system
autoping- do auto ping test
autoscr - run script from memory
base    - print or set address offset
bdinfo  - print Board Info structure
bmp     - manipulate BMP image data
boardid_prefetch- boardid sub-system
boot    - SPI-NAND-COMPATIBLE
bootc   - boot boot.img form sdcard
bootm   - boot application image from memory
bootn   - boot uImage form nand
bootp   - boot image via network using BOOTP/TFTP protocol
bootr   - boot uImage_recovery from sdcard
bootu   - boot uImage form sdcard
burnuboot- burn uboot form sdcard
calc    - command for calculate
cbusreg - cbus register read/write
chpart  - change active partition
clear_rebootmode- clear rebootmode
clkmsr  - measure PLL clock
cmp     - memory compare
coninfo - print console devices and information
cp      - memory copy
crc32   - checksum calculation
data    - SPI-NAND-COMPATIBLE || SPI-NAND-EMMC-COMPATIBLE
dcache  - enable or disable data cache
defenv  - default environment
defenv_without- defenv without environment variables
dhcp    - boot image via network using DHCP/TFTP protocol
dummy   - Customer defined command!
echo    - echo args to console
editenv - edit environment variable
efuse   - efuse version/licence/mac/hdcp/usid read/write or dump raw efuse data commands
env     - environment handling commands
ethchk  - check ethernet status
ethdbg  - set ethernet debug level
ethmode - set ethernet mac mode
ethrst  - reset ethernet phy
exit    - exit script
ext2load- load binary file from a Ext2 filesystem
ext2ls  - list files in a directory (default /)
false   - do nothing, unsuccessfully
fatexist- find the file from a dos filesystem
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls   - list files in a directory (default /)
get_img_size- get img size and save the result as a environment variable
get_rebootmode- get reboot mode
go      - start application at address 'addr'
hdcp    - HDCP sub-system
help    - print command description/usage
icache  - enable or disable instruction cache
imxtract- extract a part of a multi-image
init_wifi- init wifi power
irkey   - irkey key_value time_value
itest   - return true/false on integer compare
kgdb    - enter gdb remote debug mode
ledflicker- Led flicker when there is no uImage or recovery can run
loadb   - load binary file over serial line (kermit mode)
loadenv - load environment at address 'addr'
loads   - load S-Record file over serial line
loadx   - load binary file over serial line (xmodem mode)
loady   - load binary file over serial line (ymodem mode)
loop    - infinite loop on address range
macreg  - ethernet mac register read/write/dump
md      - memory display
mdc_clk - do mdc clock
mm      - memory modify (auto-incrementing address)
mmc     - MMC sub system
mmcinfo - display MMC info
msleep  - delay execution for some time
mtdparts- define flash/nand partitions
mtest   - simple RAM read/write test
mw      - memory write (fill)
nand    - NAND sub-system
nboot   - boot from NAND device
netspd_f- enforce eth speed
nm      - memory modify (constant address)
phyreg  - ethernet phy register read/write/dump
ping    - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
rarpboot- boot image via network using RARP/TFTP protocol
reset   - Perform RESET of the CPU
run     - run commands in an environment variable
saradc  - saradc sub-system
saveenv - save environment variables to persistent storage
secukey - security KEY sub-system
setenv  - set environment variables
sf      - SPI flash sub-system
showvar - print local hushshell variables
sleep   - delay execution for some time
source  - run script from memory
ssecukey- NAND KEY sub-system
test    - minimal test like /bin/sh
tftpboot- boot image via network using TFTP protocol
tiny_usbtool- start tiny USB tool for PC burner
true    - do nothing, successfully
unpackimg- unpack imgpack to single
usb     - USB sub-system
usbbc   - test usb bc
usbboot - boot from USB device
usid_prefetch- usid sub-system
uuid_prefetch- uuid sub-system
version - print monitor, compiler and linker version
video   - video sub-system
回复 支持 反对

使用道具 举报

板凳
 楼主| 发表于 2021-3-30 20:04 | 只看该作者

EC3_MX_PANEL_V6 #?
?       - alias for 'help'
adtask  - Ad task when time is not boot time it will sleep
aeschk  - aeschk AES algorithm check sub-system
autoping- do auto ping test
autoscr - run script from memory
base    - print or set address offset
bdinfo  - print Board Info structure
bmp     - manipulate BMP image data
boardid_prefetch- boardid sub-system
boot    - SPI-NAND-COMPATIBLE
bootc   - boot boot.img form sdcard
bootm   - boot application image from memory
bootn   - boot uImage form nand
bootp   - boot image via network using BOOTP/TFTP protocol
bootr   - boot uImage_recovery from sdcard
bootu   - boot uImage form sdcard
burnuboot- burn uboot form sdcard
calc    - command for calculate
cbusreg - cbus register read/write
chpart  - change active partition
clear_rebootmode- clear rebootmode
clkmsr  - measure PLL clock
cmp     - memory compare
coninfo - print console devices and information
cp      - memory copy
crc32   - checksum calculation
data    - SPI-NAND-COMPATIBLE || SPI-NAND-EMMC-COMPATIBLE
dcache  - enable or disable data cache
defenv  - default environment
defenv_without- defenv without environment variables
dhcp    - boot image via network using DHCP/TFTP protocol
dummy   - Customer defined command!
echo    - echo args to console
editenv - edit environment variable
efuse   - efuse version/licence/mac/hdcp/usid read/write or dump raw efuse data commands
env     - environment handling commands
ethchk  - check ethernet status
ethdbg  - set ethernet debug level
ethmode - set ethernet mac mode
ethrst  - reset ethernet phy
exit    - exit script
ext2load- load binary file from a Ext2 filesystem
ext2ls  - list files in a directory (default /)
false   - do nothing, unsuccessfully
fatexist- find the file from a dos filesystem
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls   - list files in a directory (default /)
get_img_size- get img size and save the result as a environment variable
get_rebootmode- get reboot mode
go      - start application at address 'addr'
hdcp    - HDCP sub-system
help    - print command description/usage
icache  - enable or disable instruction cache
imxtract- extract a part of a multi-image
init_wifi- init wifi power
irkey   - irkey key_value time_value
itest   - return true/false on integer compare
kgdb    - enter gdb remote debug mode
ledflicker- Led flicker when there is no uImage or recovery can run
loadb   - load binary file over serial line (kermit mode)
loadenv - load environment at address 'addr'
loads   - load S-Record file over serial line
loadx   - load binary file over serial line (xmodem mode)
loady   - load binary file over serial line (ymodem mode)
loop    - infinite loop on address range
macreg  - ethernet mac register read/write/dump
md      - memory display
mdc_clk - do mdc clock
mm      - memory modify (auto-incrementing address)
mmc     - MMC sub system
mmcinfo - display MMC info
msleep  - delay execution for some time
mtdparts- define flash/nand partitions
mtest   - simple RAM read/write test
mw      - memory write (fill)
nand    - NAND sub-system
nboot   - boot from NAND device
netspd_f- enforce eth speed
nm      - memory modify (constant address)
phyreg  - ethernet phy register read/write/dump
ping    - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
rarpboot- boot image via network using RARP/TFTP protocol
reset   - Perform RESET of the CPU
run     - run commands in an environment variable
saradc  - saradc sub-system
saveenv - save environment variables to persistent storage
secukey - security KEY sub-system
setenv  - set environment variables
sf      - SPI flash sub-system
showvar - print local hushshell variables
sleep   - delay execution for some time
source  - run script from memory
ssecukey- NAND KEY sub-system
test    - minimal test like /bin/sh
tftpboot- boot image via network using TFTP protocol
tiny_usbtool- start tiny USB tool for PC burner
true    - do nothing, successfully
unpackimg- unpack imgpack to single
usb     - USB sub-system
usbbc   - test usb bc
usbboot - boot from USB device
usid_prefetch- usid sub-system
uuid_prefetch- uuid sub-system
version - print monitor, compiler and linker version
video   - video sub-system
回复 支持 反对

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

Archiver|新帖|标签|软件|Sitemap|ZNDS智能电视网 ( 苏ICP备2023012627号 )

网络信息服务信用承诺书 | 增值电信业务经营许可证:苏B2-20221768 丨 苏公网安备 32011402011373号

GMT+8, 2024-4-26 21:25 , Processed in 0.068335 second(s), 13 queries , Redis On.

Powered by Discuz!

监督举报:report#znds.com (请将#替换为@)

© 2007-2024 ZNDS.Com

快速回复 返回顶部 返回列表