請大家幫忙看下我的A31S的海美迪H7四核是什麽問題,還有救...

superfire · 发表于 2018-3-9 20:49

本帖最后由 kingtt1994 于 2018-3-9 20:57 编辑

請大家幫忙看下我的A31S的海美迪H7四核是什麽問題,還有救不?
這個是普通啓動的信息

HELLO! BOOT0 is starting!

boot0 version : 3.0.0

reg_addr 0x01f00100 =0x00000000

reg_addr 0x01f00104 =0x00000000

reg_addr 0x01f00108 =0x00000000

reg_addr 0x01f0010c =0x00000000

reg_addr 0x01f00110 =0x00000000

reg_addr 0x01f00114 =0x00000000

[DRAM]ver 1.03 clk = 432

cpu 1 pmu 1

dram size =1024

card boot number = 2

card no is 2

sdcard 2 line count 0

[mmc]: SD/MMC Card: 4bit, capacity: 7393MB

[mmc]: vendor: Man 0x00880803 Snr 0x00000670

[mmc]: product: NCard

[mmc]: revision: 1.0

sdcard 2 init ok

The size of uboot is 0x000b0000.

sum=0xa3365caa

src_sum=0xa3365caa

Succeed in loading uboot from sdmmc flash.

Ready to disable icache.

Jump to secend Boot.

[    0.289]

U-Boot 2011.09-rc1-dirty (Sep 19 2015 - 12:30:50) Allwinner Technology

[    0.297]version: 1.1.0

[    0.300]pmbus: ready

[    0.303]PMU: AXP221

[    0.305]PMU: AXP22x found

[    0.308]PMU: bat ratio = 100

[    0.311]PMU: dcdc3 1260

[    0.314]PMU: pll1 1008 Mhz

dcdc1_vol = 3000

dcdc2_vol = 1200

dcdc3_vol = 1260

dcdc4_vol = 1240

dcdc5_vol = 1500

aldo2_vol = 1800

aldo3_vol = 3000

cpus_source = 1

gpio1ldo_vol = 3100

find power_sply to end

no battery, limit to dc

fel key old mode

run key detect

no key found

dram_para_set start

dram_para_set end

[    0.421]DRAM:  1 GiB

relocation Offset is: 35b18000

don't initialize the user_gpio

deu_mode1 not exist.

lcdgamma4iep for lcd1 not exist.

[TV]bsp_disp_set_tv_func

[TV]gm7121_module_init finish!

DRV_DISP_Init: opened

[    0.646]boot_disp.output_type=2

[    0.649]boot_disp.output_mode=5

[    0.653]boot_disp.auto_hpd=1

[TV]gm7121_tv_power_on

[TV]gm7121_init, tv_Mode=11

workmode = 0

MMC:    2

SUNXI SD/MMC: 2

Man 880803 Snr 00000670

NCard

1.0

boot0 capacity: 0KB,boot1 capacity: 0KB

[    1.193]sunxi flash init ok

probe mmc0 if exist

SUNXI SD/MMC: 2, SUNXI SD/MMC: 0

[mmc]: cmd 8 timeout, err 100

[mmc]: mmc cmd 8 err 0x00000100

mmc send if cond failed

[mmc]: cmd 55 timeout, err 100

[mmc]: mmc cmd 55 err 0x00000100

send app cmd failed

[mmc]: cmd 1 timeout, err 100

[mmc]: mmc cmd 1 err 0x00000100

mmc send op cond failed

Card did not respond to voltage select!

MMC0 init failed

In: serial

Out: serial

Err: serial

--------fastboot partitions--------

-total partitions:11-

-name-       -start-    -size-

bootloader  : 1000000    1000000

env       : 2000000    1000000

boot       : 3000000    1000000

system    : 4000000    20000000

data       : 24000000    60000000

misc       : 84000000    1000000

recovery : 85000000    2000000

cache    : 87000000    1c000000

private    : a3000000    1000000

databk    : a4000000    1000000

UDISK    : a5000000    0

-----------------------------------

base bootcmd=run setargs_mmc boot_normal

bootcmd set setargs_mmc

key 0

cant find rcvy value

cant find fstbt value

Recovery detected, will usb recovery

to be run cmd=run setargs_mmc boot_recovery

user data is updataed

user data is updataed

WORK_MODE_BOOT

sunxi_bmp_display

blkcnt should not be 0

[    1.601]Hit any key to stop autoboot:  0

read boot or recovery all

[    5.791]sunxi flash read :offset 85000000, 13585117 bytes OK

no signature

[    5.801]ready to boot

[    5.803]

Starting kernel ...

<[ 1.140565] Initramfs unpacking failed: uncompression error

[ 1.178081] sun6i_vibrator_init motor is not used in config

[ 1.363875] ctp_fetch_sysconfig_para: ctp_unused.

[ 1.446563] otg_wakelock_init: No OTG transceiver found

[ 1.457885] init: cannot find '/sbin/ueventd', disabling 'ueventd'

[ 6.022399] init: Timed out waiting for /dev/.coldboot_done

[ 6.029103] init: open display device failed!

[ 6.034329] init: ##av is unsupported

[ 6.038693] init: open display device failed!

[ 6.043686] init: open display device failed!

[ 6.048579] init: open display device failed!

[ 6.049542] init: cannot find '/sbin/busybox', disabling 'initpartition'

[ 6.061009] init: open display device failed!

[ 6.065914] init: open display device failed!

[ 6.070808] init: HDMI status = -1, try 1 times!TV status = 0

[ 6.170408] init: Unable to open persistent property directory /data/property errno: 2

[ 6.179506] init: untracked pid 857 exited

[ 6.185200] init: cannot find '/sbin/recovery', disabling 'recovery'

[ 6.192465] init: cannot find '/sbin/adbd', disabling 'adbd'

然後卡住不動了

bug无敌 · 发表于 2018-3-9 20:57

能否上个图

superfire · 发表于 2018-3-10 11:23

bug无敌发表于 2018-3-9 20:57
能否上个图

就是這樣搞,開機后讀取得到的TTL信息

ZMJ1111 · 发表于 2018-3-16 16:31

学习学习！

superfire · 发表于 2018-3-18 13:00

ZMJ1111 发表于 2018-3-16 16:31
学习学习！

互相學習而已

› 你问我答 / 玩机教程 / 固件 › ZNDS刷机/救砖

請大家幫忙看下我的A31S的海美迪H7四核是什麽問題,還有 ...

請大家幫忙看下我的A31S的海美迪H7四核是什麽問題,還有救...

相关帖子