860A1.1 系统升级后 TTL 进不去了

yxypliu · 发表于 2018-1-7 19:06

AC_ON
MIU0_DQS-OK
BIST0-▒▒▒
MIU0-1024_U
Start uboot
Relocation Offset is: 015d7000
[AT][MB][start ub][314]
U-Boot 2011.06-00114-ga7f97e5-dirty (Oct 23 2017 - 23:15:16)

[MIU INFO] miu opencreate instance at 51be9418 with private size 80 bytes at 51b    e9460
create instance at 51be94b8 with private size 52 bytes at 51be9500
uboot held at [519ddf60~52d00000],size=013220a0
CPU  : Clippers
Board: BD_MST207C_D01A_S_CLIPPERS
DRAM:  813 MiB
Now running in RAM - U-Boot at: 51e00000
eMMC: HS200 200MHz
eMMC 3.68 GB [75FFF8h]
In: serial
Out: serial
Err: serial
Net: zte_shutdow =false
No ethernet found.
Set MAC default
MAC:  0x0: 0x30: 0x1b: 0xba:0x2: 0xdb
msIR_Initialize
[CPU INFO] cpu opencreate instance at 51bf99c0 with private size 44 bytes at 51b    f9a08
CPUIoctl - MDrv_CMD_CPU_QueryClock
[UTOPIA INFO] close moduleNames[38]: MODULE_CPU
[AT][MBoot][Driver Init][544]
### main_loop entered: s is true
### main_loop entered: bootdelay=1

Starting logo
============= set bootargs ===============
[setup_com_controlenv] COMControlFlag=> value[1]=, val=0
zte_mac=90:D8:F3:E3:2A:3E,ethaddr=90:D8:F3:E3:2A:3E
Hit any key to stop autoboot: 1@
step1 error...
abort=0                                                                      0
do_bootcheck called
MMC_CAPACITY_512 =7733240
current emmc size is =0x75fff8 (should by 512)
MMCusrdata_size =3901440
current userdata size =0x3b8800 (should by 512)
get_boot1_ver cmd_boot1=mmc read.boot 1 0x25000000 0x0 0x200000
set hdmi hdcp mode 0!
Saving Environment to MMC...
Writing to MMC(0)... 128 blocks written: OK
128 blocks written: OK
done
iTVSTandard2Resolution = 2
value[29] = 5510049900703340000090D8F3E32A3E
[setup_bootenv] COMControlFlag=> value[30]=, val=0
ethaddr =90:D8:F3:E3:2A:3E
jy ....
search ....
waldo msIR_GetIRKeyCode line:482 breturn false
fore uup IRKey [0xff]
BootMode=0
search ....
waldo msIR_GetIRKeyCode line:482 breturn false
fore uup IRKey [0xff]
BootMode=0
search ....
waldo msIR_GetIRKeyCode line:482 breturn false
fore uup IRKey [0xff]
BootMode=0
search ....
waldo msIR_GetIRKeyCode line:482 breturn false
fore uup IRKey [0xff]
BootMode=0
search ....
waldo msIR_GetIRKeyCode line:482 breturn false
fore uup IRKey [0xff]
BootMode=0
search ....
waldo msIR_GetIRKeyCode line:482 breturn false
fore uup IRKey [0xff]
BootMode=0
search ....
waldo msIR_GetIRKeyCode line:482 breturn false
fore uup IRKey [0xff]
BootMode=0
search ....
waldo msIR_GetIRKeyCode line:482 breturn false
fore uup IRKey [0xff]
BootMode=0
search ....
waldo msIR_GetIRKeyCode line:482 breturn false
fore uup IRKey [0xff]
BootMode=0
search ....
waldo msIR_GetIRKeyCode line:482 breturn false
fore uup IRKey [0xff]
BootMode=0
[ztebsp] BootMode=0
[do_bootcheck,1181][ZTEWatchdog]PATCH FOR zte BEGIN
[do_bootcheck,1185][ZTEWatchdog] Watchdog_enable TRUE
[do_bootcheck,1191][ZTEWatchdog] Watchdog start, MAXTIME 120
create instance at 51bf9bb0 with private size 256 bytes at 51bf9bf8
MDrv_PNL_Init u32PnlRiuBaseAddr = 1f200000
MDrv_PNL_Init u32PMRiuBaseAddr = 1f000000
PNL:[MDrv_PNL_SetPanelType][613]
[_MDrv_PNL_Init_LPLL][323]pstPanelInitData->u16Width=1280, pstPanelInitData->u16    Height=720
[_MDrv_PNL_Init_LPLL][325]u16HTotal=1980,u16VTotal=750,pstPanelInitData->u16HTot    al=1980,pstPanelInitData->u16VTotal=750, u16DefaultVFreq=500
[_MDrv_PNL_Init_Output_Dclk][369]pstPanelInitData->u16Width=1280, pstPanelInitDa    ta->u16Height=720
[_MDrv_PNL_Init_Output_Dclk][371]u16HTotal=1980,u16VTotal=750,pstPanelInitData->    u16HTotal=1980,pstPanelInitData->u16VTotal=750, u16DefaultVFreq=500
PNL:CalculateLPLLSETbyDClk u32KHz = 742500000, u64DefaultLdHz = 742500000
PNL:CalculateLPLLSETbyDClk u32LpllSet = 3531df
[MApi_XC_MLG_GetStatus, 1603]No instance existed, please get an instance by call    ing MApi_XC_Init() first
msHdmitx_Disp_Init
create instance at 51bf9d00 with private size 1720 bytes at 51bf9d48
[XC,Version]
no need to patchcreate instance at 51bfa948 with private size 80 bytes at 51bfa    990
Rx Support HDMI mode!
HDMI CONNECT! isBoOTToRecovery = 0
shift -8 pixels in PAL mode
Create Dolby single part name task failed!![Hal_VE_Set_PreHSD][1826] ERROR!!! HV    SD H input = 0, HVSD H output = 720
[Hal_VE_Set_PreVSD][2002] ERROR!!! HVSD V input = 0, HVSD V output = 576
[Hal_VE_EnableDI][2110] bEnable = 0, bIsDNR2VE = 0
lyndon Hal_VE_Set_PreVSD 1mmc change mount : tvcustomer
Size of file "/720.jpg" from mmc device 0 partition tvcustomer: 152910 bytes
Loading file "/720.jpg" at offset 0x0 from mmc device 0 partition tvcustomer
152910 bytes read
create instance at 51bfa9e8 with private size 304 bytes at 51bfaa30
[AT][MB][JPD Decode][5564]
[UTOPIA INFO] close moduleNames[35]: MODULE_NJPEG_EX
create instance at 51bfa9e8 with private size 132280 bytes at 51bfaa30
[GOP INFO] gop opencreate instance at 51c1aef0 with private size 6908 bytes at 5    1c1af38
[AT][MB][Show Logo][5611]
## Booting kernel from Legacy Image at 25000800 ...
Image Name: MStar-linux
Image Type: ARM Linux Multi-File Image (uncompressed)
Data Size: 5317432 Bytes = 5.1 MiB
Load Address: 20208000
Entry Point:  20208000
Contents:
   Image 0: 4627208 Bytes = 4.4 MiB
   Image 1: 690212 Bytes = 674 KiB
## Loading init Ramdisk from multi component Legacy Image at 25000800 ...
-usb_stop(USB_PORT0)
-usb_stop(USB_PORT1)
-usb_stop(USB_PORT2)
Loading Multi-File Image ... OK
[AT][MB][start kr][5869]
Starting kernel ...
[PROTECT ERROR], not expected dram size: 0x0
#######################################################################
# [PROTECT WARNING], miu kernel protect is not enabled on second dram #
#######################################################################
Uncompressing Linux... done, booting the kernel.
KERN-3.10.23.001049551
tommy: thread_info_cache_init
mtdoops: mtd device (mtddev=name/number) must be supplied
[drivers/mstar2/drv/emac/mdrv_emac.c MDev_EMAC_HW_init 2196] ready init mute
[drivers/mstar2/drv/emac/mdrv_emac.c MDev_EMAC_HW_init 2197] after init mute
RBQP_BASE = 50304000
init: /init.clippers.rc: 455: ignored duplicate definition of service 'mdnsd'
init: /zte_init.rc: 38: ignored duplicate definition of service 'xiriservice'
init: ## ProductID: strlen (32)!
healthd: No charger supplies found
init: cannot find '/system/bin/xiriservice_ChinaMobile_SiChuan', disabling 'b       toothd'
init: cannot find '/system/bin/bleservice', disabling 'bleservice'

电脑系统是win10  64位用的是CH340和putty

橙橙橙子丶 · 发表于 2018-1-7 23:59

看不懂哇这么多

zxslt · 发表于 2018-1-8 00:07

是的，封了

syl330046 · 发表于 2018-1-11 23:00

我也是这样进不去输入不了指令

syl330046 · 发表于 2018-1-11 23:00

我也是这样进不去输入不了指令

luoren123 · 发表于 2018-1-12 20:36

我和你一样的问题，我的是XP的。唉。。。。

luoren123 · 发表于 2018-1-12 20:36

zxslt 发表于 2018-1-8 00:07
是的，封了

讲详细点，这盒子还有希望破吗？

antcipate · 发表于 2018-1-13 22:58

我的现象和你一样，你解决了吗

yxypliu · 发表于 2018-9-19 19:07

antcipate 发表于 2018-1-13 22:58
我的现象和你一样，你解决了吗

淘宝花钱弄好了

Jason_TOTO · 发表于 2018-9-26 11:29

yxypliu 发表于 2018-9-19 19:07
淘宝花钱弄好了

是怎么弄的？能把过程分享一下吗？

› 运营商IPTV / 有线电视 / 广电机顶盒 › 中兴机顶盒

860A1.1 系统升级后 TTL 进不去了

860A1.1 系统升级后 TTL 进不去了

相关帖子