求救砖付费江苏移动创维E900V21C

jiyong123 · 发表于 2017-12-21 12:08

本帖最后由 jiyong123 于 2017-12-21 12:17 编辑

      @hao501802766
      前两天刚刚把刷机心得（2017年12月江苏移动创维E900V21C刷机成功）和大家分享了。由于彻底关机后再开机，WIFI需要手动连接，觉得是固件版本的问题，昨晚重新试了《乐天20170828版-卡刷包》，刷完盒子重启，盒子就再也没亮起来了，电视直接什么图像都没有。
   换了2台电脑，3条USB线， 2条TTL线（CH341线，PL2303线）

故障现象：
1、通电后，主板上PWR主电源灯亮一下绿灯就变红了；LAN网口灯一直红灯；IR遥控灯一直是熄灭状态。
2、刷机软件USB_Burning_Tool，一直发现不了盒子，且反复开关都不识别。
3、TTL跑到一半就卡住了，怎么回车都没反应，试了很多次。
Starting kernel ...
uboot time: 2041271 us
[ 0.000000@0] Initializing cgroup subsys cpu
[ 0.000000@0] Initializing cgroup subsys cpuacct
[ 0.000000@0] Linux version 3.14.29-svn125577 (chenshouhui@ubuntu) (gcc version 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.09 - Linaro GCC 4.9-2014.09) ) #1 SMP PREEMPT Sat Mar 18 22:16:52 HKT 2017
[ 0.000000@0] CPU: armv71 Processor [410fd034] revision 4
[ 0.000000@0] bootconsole [earlycon0] enabled
INFO: HDCP22 key read fail!
INFO: p1d 0
INFO: pd1 0

4、TTL完整信息在2楼
求救砖付费江苏移动创维E900V21C

jiyong123 · 发表于 2017-12-21 12:09

GXL:BL1:9ac50e:a1974b;FEAT:ADFC318C;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 101949

BL2 Built : 18:58:24, Oct 25 2016.
gxl gc9db010 - xiaobo.gu@droid05

set vcck to 1080 mv
set vddee to 1050 mv
Board ID = 2, adc=153
CPU clk: 1200MHz
2layers board, use ddr_set[0]
DDR chl: Rank0+1 @ 720MHz - FAIL
DDR chl: Rank0 @ 720MHz - PASS
DQS-corr enabled
DDR scramble enabled
Rank0: 1024MB(auto)-2T-11
DataBus test pass!
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
Load bl30 from eMMC, src: 0x00010200, des: 0x01100000, size: 0x00007400
Load bl301 from eMMC, src: 0x00018200, des: 0x01200000, size: 0x00002000
Load bl31 from eMMC, src: 0x0001c200, des: 0x10100000, size: 0x00019400
Load bl33 from eMMC, src: 0x00038200, des: 0x01000000, size: 0x000a6200
NOTICE:  BL3-1: v1.0(debug):959fdf0
NOTICE:  BL3-1: Built : 15:01:44, Dec 29 2016
aml log : bl31 normal boot !
[Image: gxl_v1.1.3086-872dec0 2016-09-21 21:56:30 xiaobo.gu@droid05]
bl30: check_permit, count is 1
bl30: check_permit: ok!
chipid: ef be ad de d f0 ad ba ef be ad de not ES chip
efuse init ops = c2
efuse init hdcp = c, cf9=7
[0.414842 Inits done]
seINFcOu:r e t aBsLk3 -s1t:a rItn!it
ializing runhtiigmhe  tsaesvices
WARNING: No OPTEE provided by BL2 boot loader
ERROR: Error initializing runtime service opteed_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x1000000
INFO: BL3-1: Next image spsr = 0x3c9

U-Boot 2015.01-svn125577 (Mar 18 2017 - 21:47:22)

DRAM:  1 GiB
Relocation Offset is: 36ecf000
gpio: pin GPIODV_24 (gpio 43) value is 0
gpio: pin GPIOAO_3 (gpio 103) value is 1
mwm 0xc8837004:[0x aa203] with [0x ea203] ok
mwm 0xc883700c:[0x 3e3b744] with [0x 3e3b764] ok
mwm 0xc8837010:[0x c0101] with [0x c8101] ok
mwm 0xc8837010:[0x c8101] with [0x  128101] ok
register usb cfg[0][1] = 0000000037f63db0
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
boot_device_flag : 1
Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
init bus_cycle=6, bus_timing=7, system=5.0ns
reset failed
get_chip_type and ret:fffffffe
get_chip_type and ret:fffffffe
chip detect failed and ret:fffffffe
nandphy_init failed and ret=0xfffffff1
MMC: aml_priv->desc_buf = 0x0000000033ebfdb0
aml_priv->desc_buf = 0x0000000033ec20d0
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x1ff2800
emmc/sd response timeout, cmd55, status=0x1ff2800
[mmc_startup] mmc refix success
[mmc_init] mmc init success
overide_emmc_partition_table: overide cache
[mmc_get_partition_table] skip partition cache.
mmc read lba=0x12000, blocks=0x2
mmc read lba=0x12002, blocks=0x2
mmc_read_partition_tbl: mmc read partition OK!
eMMC/TSD partition table have been checked OK!
mmc env offset: 0x27400000
In: serial
Out: serial
Err: serial
board id is : 2
hpd_state=1
[720p50hz] is invalid for cvbs.
set hdmitx VIC = 19
config HPLL = 2972
HPLL: 0xc000027b
config HPLL done
j = 2  vid_clk_div = 1
hdmitx phy setting done
hdmitx: set enc for VIC: 19
enc_vpu_bridge_reset[1189]
rx version is 1.4 or below  div=10
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
read emmc dtb
dwmac.c9410000
Error: dwmac.c9410000 address not set.

wipe_data=successful
wipe_cache=successful
upgrade_step=2
reboot_mode=cold_boot
[CANVAS]canvas init
[CANVAS]addr=0x3d800000 width=5760, height=2160
[OSD]ERR: 24 bit/pixel mode, but BMP has 16 bit/pixel
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0
amlkey_issecure() 138: ret 1
amlkey_size() 162: ret 1
[KM]Error:f[key_unify_read]L301:key[mac] not programed yet
[KM]Error:f[do_sec_keyunify]L682:mac key read fail
don't use random mac produce in uboot
IR init done!
gpio: pin GPIOH_6 (gpio 55) value is 1
Hit any key to stop autoboot:  0
ee_gate_off ...
## Booting Android Image at 0x01080000 ...
reloc_addr =33f44bc0
copy done
   Single dtb detected
load dtb from 0x1000000 ......
Uncompressing Kernel Image ... OK
kernel loaded at 0x01080000, end = 0x02033200
Loading Ramdisk to 33c36000, end 33ebca00 ... OK
Loading Device Tree to 000000001fff3000, end 000000001ffff3a1 ... OK

Starting kernel ...

uboot time: 2041271 us
[ 0.000000@0] Initializing cgroup subsys cpu
[ 0.000000@0] Initializing cgroup subsys cpuacct
[ 0.000000@0] Linux version 3.14.29-svn125577 (chenshouhui@ubuntu) (gcc version 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.09 - Linaro GCC 4.9-2014.09) ) #1 SMP PREEMPT Sat Mar 18 22:16:52 HKT 2017
[ 0.000000@0] CPU: armv71 Processor [410fd034] revision 4
[ 0.000000@0] bootconsole [earlycon0] enabled
INFO: HDCP22 key read fail!
INFO: p1d 0
INFO: pd1 0

hao501802766 · 发表于 2017-12-21 12:39

jiyong123 发表于 2017-12-21 12:09
GXL:BL1:9ac50e:a1974b;FEAT:ADFC318C;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 101949

用双头USB 重刷这个包：https://www.znds.com/rom/20132.html

jiyong123 · 发表于 2017-12-21 12:44

hao501802766 发表于 2017-12-21 12:39
用双头USB 重刷这个包：https://www.znds.com/rom/20132.html

双头的线换了好几条了
刷机软件一直识别不到盒子

hao501802766 · 发表于 2017-12-21 12:45

jiyong123 发表于 2017-12-21 12:44
双头的线换了好几条了
刷机软件一直识别不到盒子

盒子接通电源开机然后马上插入USB 应该可以我是这样刷机操作基本都OK

jiyong123 · 发表于 2017-12-21 13:05

我都是关机，插上USB，再插电源，不行！
按你的方法连续测试了20次还是不行！
软件发现不了盒子

hao501802766 · 发表于 2017-12-21 13:55

那我也没好的办法了要么就选择寄过来我试试看当然也不保证一定能弄好

jiyong123 · 发表于 2017-12-21 14:04

hao501802766 发表于 2017-12-21 13:55
那我也没好的办法了要么就选择寄过来我试试看当然也不保证一定能弄好 ...

可以的江浙沪范围发给你们很方便的

jiyong123 · 发表于 2017-12-21 16:07

hao501802766 发表于 2017-12-21 13:55
那我也没好的办法了要么就选择寄过来我试试看当然也不保证一定能弄好 ...

地址已收到，没权限发短消息。这里回复，明天发快递出去

jiyong123 · 发表于 2017-12-24 20:01

@hao501802766
快递已发申通402886040185

› 你问我答 / 玩机教程 / 固件 › ZNDS刷机/救砖