本帖最后由 wuli小茶 于 2017-12-10 22:46 编辑
跑码出现如下结果，不能输入代码，请各位大神帮忙看看怎么办，谢谢~~~
- ROM6716V1[url=home.php?mod=space&uid=154382]@jun[/url] 6 201610:51:31
- MODE:EMMC
- Jump
- B16_COMP BL1 [url=home.php?mod=space&uid=354241]@May[/url] 8 2017
- A53 down
- pll ok!
- C/T
- ddr 1866M svn9645 finish
- EMMC
- chip id ERR
- mN0^^: a53
- mO0^^: B16_COMP
- mT0^^: stby work low
- ICE: bl31_early_platform_setup
- INFO: bl31_plat_arch_setup
- NOTICE: BL31: v1.2(debug):svn 16266
- NOTICE: BL31: Built : 09:55:24, Apr 12 2017
- NOTICE: B16XX
- INFO: bl31_platform_setup
- INFO: GICv3 without legacy support detected. ARM GICV3 driver initialized in EL3
- INFO: BL31: Initializing runtime services
- INFO: BL31: Preparing for EL3 exit to normal world
- INFO: Entry point address = 0x4f000000
- INFO: SPSR = 0x3c5
- U-Boot 2015.10-gf7f5fc4 (Nov 06 2017 - 18:29:14 +0800)
- DRAM: 1 GiB
- agpio13 =1 ,agpio6 =1
- GPIO reset phy. GPIO = 57
- MMC: eMMC: 0
- Using default environment
- In: serial
- Out: serial
- Err: serial
- board_late_init
- io_ctrl_idle:a16cxx
- zx_keycol2_keyrow1_pwm_init_table_1!
- ZX_OTP_VDD_INFO = 0!
- Net: CONFIG_ETH_DESIGNWARE_QOS_420
- phy reset ok
- confs rtn=0, g_enetaddr=28:8c:b8:94:47:54
- dwmac.5200000
- [setup_com_controlenv] COMControlFlag=> value[1]=0, val=0
- ## Error: Can't overwrite "ethaddr"
- ## Error inserting "ethaddr" variable, errno=1
- zte_mac=00:02:f7:ef:00:02,ethaddr=00:02:f7:ef:00:02
- Hit any key to stop autoboot: 0 in the 280*************
- in thebootdelay=0************
- in abort=0*********** 0
- MMC read: dev # 0, block # 2179072, count 1 ... 1 blocks read: OK
- misc:
- ***********val=0********************************
- MMC read: dev # 0, block # 1867776, count 1 ... 1 blocks read: OK
- MMC read: dev # 0, block # 1867776, count 388 ... 388 blocks read: OK
- logo_load_addr is 0x77000000
- [setup_bootenv] COMControlFlag=> value[9]=0, val=0
- *******************MarketCodenew is 36**********
- TVMode: val:0001000100080000
- do_bootsys to boot NORM
- MMC read: dev # 0, block # 2260992, count 2 ... 2 blocks read: OK
- MMC read: dev # 0, block # 2260996, count 23509 ... 23509 blocks read: OK
- kernel_addr in header:0x40008000
- MMC read: dev # 0, block # 2284504, count 2621 ... 2621 blocks read: OK
- MMC read: dev # 0, block # 2287124, count 261 ... 261 blocks read: OK
- enable emmc rst n function:mmc rst 0 1
- setenv bootargs root=/dev/ram0 rw initrd=0x41000000,0x1470b0 boardtype=0x3 console=ttyS0,115200n8 ${othbootargs} stmmaceth=chain_mode:1 kgdboc=ttyS0,115200 loglevel=3 swiotlb=0x800 androidboot.hardware=zxic androidboot.selinux=disabled boot_revision=V0033 market=36,1 LogoDataAddr=0x77000000 WorkMode=0 LogoDisplayModel=0 AutoOutputFlag= HDMIAdaptiveMode=0 StandbyIRCode=bf40ff00 ProductID=FC100499007037200000288CB8944754 BootVideoCtrl=0 COMControlFlag=0 TVMode=0001000100080000 576DispInfo=0012001006990557 480DispInfo=0012001006980460 720DispInfo=0017000812450704 1080DispInfo=0023001518741050 4KDispInfo=0000000038402160
- secure=0 board:a16c00
- ## Flattened Device Tree blob at 40e00000
- Booting using the fdt blob at 0x40e00000
- Using Device Tree in place at 0000000040e00000, end 0000000040e0a48a
- Starting kernel ...
- [ 1.083261] init_softpoweroff_sctrl: gpio software power-off reg = 0x1160a433
|
网站导航
发表于 2017-12-10 17:56
收藏
淘帖
顶一个
踩
提升卡
置顶卡
变色卡
千斤顶
znds.com 