歌华dvbip1001原版系统和当贝桌面精简系统线刷包

libao

楼主，我使用擦除全器件了，现在刷上系统后一直重启。Tuning datastrobe[1,15],set[8],type[0]
MMC/SD Card:
    MID:         0x15
    Read Block:  512 Bytes
    Write Block: 512 Bytes
    Chip Size:   7456M Bytes (High Capacity)
    Name:        "8GME4R"
    Chip Type:   MMC
    Version:     5.1
    Speed:       150000000Hz
    Mode:        HS400
    Voltage:     1.8V
    Bus Width:   8bit
    Boot Addr:   0 Bytes

Boot Env on eMMC
    Env Offset:          0x00100000
    Env Size:            0x00010000
    Env Range:           0x00010000


SDK Version: HiSTBAndroidV600R002C00SPC031_v2016051915

Security Begin Read RSA CRC Key in USB disk!
Security Read RSA CRC Key in USB disk failed, length is -1
mac:00:e4:00:57:e5:02
get chipid =37980200
get chipType (Hi3798CV200)
count=2
get rc key fail, continue next loop
get rc key fail, continue next loop
get rc key fail, continue next loop
get rc key fail, continue next loop
get rc key fail, continue next loop
get rc key fail, continue next loop
get rc key fail, continue next loop
get rc key fail, continue next loop
get rc key fail, continue next loop
get rc key fail, continue next loop
get rc key fail, continue next loop
get rc key fail, continue next loop
get rc key fail, continue next loop
get rc key fail, continue next loop
get rc key fail, continue next loop
get rc key fail, continue next loop
get rc key fail, continue next loop
get rc key fail, continue next loop
get rc key fail, continue next loop
get rc key fail, continue next loop
check_rckey_recovery->keyUpdateCount:0, keyClearCount:0, keyEnterFactoryCount:0,                      keyEnterRecovery:0, keyBurnCount:0, responseType:0
boot_select_result:kernel
g_EnvFlashAddr:0x100000, g_EnvFlashPartionSize:0x10000
CA_flash_open_addr,334: Open addr, enFlashType: 0x00000002
CA_flash_open_addr,334: Open addr, enFlashType: 0x00000002
HI_CA_Verify_BootPara,412: Check BootPara authenitication is ok
CA_CMD_VerifyBootParaByPartName,50: verify success
CA_CMD_AdvcaAuthByPartName,78: advca_verify: kernel
pstImgInfo->length = 0x2e656c75
Attempt to write outside the flash handle area, flash handle size: 0x02800000, o                      ffset: 0x00000000, length: 0x2e656c00
CA_flash_read,248: HI_Flash_Read partion kernel error
HI_CA_AdvcaVerifyByPartName,433: run CA_flash_read((HI_CHAR*)pPartionName,0ULL,(                      ImgInfo.length+CH_NOVEL_HEAD_LEN),(HI_U8*)u32RamAddr, HI_NULL) failed, ERRNO:0xf                      fffffff.
CA_CMD_AdvcaAuthByPartName,79: run HI_CA_AdvcaVerifyByPartName((HI_U8*)argv[1],                       u32RamAddr, NULL) failed, ERRNO:0xffffffff.
HI_Android_Authenticate,592: Fail to verify kernel!
resetting ...


System startup


Relocate Boot

Jump to C code

libao

Tuning datastrobe[1,15],set[8],type[0]
MMC/SD Card:
    MID:         0x15
    Read Block:  512 Bytes
    Write Block: 512 Bytes
    Chip Size:   7456M Bytes (High Capacity)
    Name:        "8GME4R"
    Chip Type:   MMC
    Version:     5.1
    Speed:       150000000Hz
    Mode:        HS400
    Voltage:     1.8V
    Bus Width:   8bit
    Boot Addr:   0 Bytes

Boot Env on eMMC
    Env Offset:          0x00100000
    Env Size:            0x00010000
    Env Range:           0x00010000


SDK Version: HiSTBAndroidV600R002C00SPC031_v2016051915

Security Begin Read RSA CRC Key in USB disk!
Security Read RSA CRC Key in USB disk failed, length is -1
mac:00:e4:00:57:e5:02
get chipid =37980200
get chipType (Hi3798CV200)
count=2
get rc key fail, continue next loop
get rc key fail, continue next loop
get rc key fail, continue next loop
get rc key fail, continue next loop
get rc key fail, continue next loop
get rc key fail, continue next loop
get rc key fail, continue next loop
get rc key fail, continue next loop
get rc key fail, continue next loop
get rc key fail, continue next loop
get rc key fail, continue next loop
get rc key fail, continue next loop
get rc key fail, continue next loop
get rc key fail, continue next loop
get rc key fail, continue next loop
get rc key fail, continue next loop
get rc key fail, continue next loop
get rc key fail, continue next loop
get rc key fail, continue next loop

sntemwong

libao 发表于 2020-10-26 20:49
我全部擦除了，现在该咋办呢

我也在研究，可能行得通的方法，1找能解高安boot的软件，解后查看内部文件，或者提取内核移植到其他机器 2试试找1002 1004 1006等同样的机器的包来刷，3机器电路上一定有记录一些信息的小储存芯片，例如8脚的几M的芯片，可以取下来后放编辑器上读取信息  能力有限只能想到这么多，这东西要是到售后那边估计也就是几分钟搞定的事

libao

sntemwong 发表于 2020-10-27 10:21
我也在研究，可能行得通的方法，1找能解高安boot的软件，解后查看内部文件，或者提取内核移植到其他机器  ...

你要是解决了，麻烦也帮我解决一下。谢谢

rinnng8

楼主，刷好纯洁系统可以恢复出厂设置么？电视家3打开就闪退，而且总出现有权查看使用情况的应用窗口

sntemwong

rinnng8 发表于 2020-10-30 18:33
楼主，刷好纯洁系统可以恢复出厂设置么？电视家3打开就闪退，而且总出现有权查看使用情况的应用窗口 ...

可以回复出厂设置，闪退的原因是因为机器个别设置与我的系统不同，你可以先备份自己的全部分区后，除了三码分区不要刷，其他分区刷成我的就可以了