中兴机顶盒B860AV1.1-T2刷机问题求助
本帖最后由 wuli小茶 于 2017-12-10 22:46 编辑跑码出现如下结果，不能输入代码，请各位大神帮忙看看怎么办，谢谢~~~
ROM6716V1@jun6 201610:51:31
MODE:EMMC
Jump
B16_COMP BL1 @May8 2017
A53 down
pll ok!
C/T
ddr 1866M svn9645 finish
EMMC
chip id ERR
mN0^^: a53
mO0^^: B16_COMP
mT0^^: stby work low
ICE:bl31_early_platform_setup
INFO: bl31_plat_arch_setup
NOTICE:BL31: v1.2(debug):svn 16266
NOTICE:BL31: Built : 09:55:24, Apr 12 2017
NOTICE:B16XX
INFO: bl31_platform_setup
INFO: GICv3 without legacy support detected. ARM GICV3 driver initialized in EL3
INFO: BL31: Initializing runtime services
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0x4f000000
INFO: SPSR = 0x3c5
U-Boot 2015.10-gf7f5fc4 (Nov 06 2017 - 18:29:14 +0800)
DRAM:1 GiB
agpio13 =1 ,agpio6 =1
GPIO reset phy. GPIO = 57
MMC: eMMC: 0
Using default environment
In: serial
Out: serial
Err: serial
board_late_init
io_ctrl_idle:a16cxx
zx_keycol2_keyrow1_pwm_init_table_1!
ZX_OTP_VDD_INFO = 0!
Net: CONFIG_ETH_DESIGNWARE_QOS_420
phy reset ok
confs rtn=0, g_enetaddr=28:8c:b8:94:47:54
dwmac.5200000
COMControlFlag=> value=0, val=0
## Error: Can't overwrite "ethaddr"
## Error inserting "ethaddr" variable, errno=1
zte_mac=00:02:f7:ef:00:02,ethaddr=00:02:f7:ef:00:02
Hit any key to stop autoboot:0 in the 280*************
in thebootdelay=0************
in abort=0*********** 0
MMC read: dev # 0, block # 2179072, count 1 ... 1 blocks read: OK
misc:
***********val=0********************************
MMC read: dev # 0, block # 1867776, count 1 ... 1 blocks read: OK
MMC read: dev # 0, block # 1867776, count 388 ... 388 blocks read: OK
logo_load_addr is 0x77000000
COMControlFlag=> value=0, val=0
*******************MarketCodenew is 36**********
TVMode: val:0001000100080000
do_bootsys to boot NORM
MMC read: dev # 0, block # 2260992, count 2 ... 2 blocks read: OK
MMC read: dev # 0, block # 2260996, count 23509 ... 23509 blocks read: OK
kernel_addr in header:0x40008000
MMC read: dev # 0, block # 2284504, count 2621 ... 2621 blocks read: OK
MMC read: dev # 0, block # 2287124, count 261 ... 261 blocks read: OK
enable emmc rst n function:mmc rst 0 1
setenv bootargs root=/dev/ram0 rw initrd=0x41000000,0x1470b0 boardtype=0x3 console=ttyS0,115200n8 ${othbootargs} stmmaceth=chain_mode:1 kgdboc=ttyS0,115200 loglevel=3 swiotlb=0x800androidboot.hardware=zxic androidboot.selinux=disabled boot_revision=V0033 market=36,1 LogoDataAddr=0x77000000 WorkMode=0 LogoDisplayModel=0 AutoOutputFlag=HDMIAdaptiveMode=0 StandbyIRCode=bf40ff00 ProductID=FC100499007037200000288CB8944754 BootVideoCtrl=0 COMControlFlag=0 TVMode=0001000100080000 576DispInfo=0012001006990557 480DispInfo=0012001006980460 720DispInfo=0017000812450704 1080DispInfo=0023001518741050 4KDispInfo=0000000038402160
secure=0 board:a16c00
## Flattened Device Tree blob at 40e00000
Booting using the fdt blob at 0x40e00000
Using Device Tree in place at 0000000040e00000, end 0000000040e0a48a
Starting kernel ...
[ 1.083261]init_softpoweroff_sctrl: gpio software power-off reg = 0x1160a433
楼主可以试试这个教程https://www.znds.com/tv-1008160-1-1.html wuli小茶 发表于 2017-12-10 22:52
楼主可以试试这个教程https://www.znds.com/tv-1008160-1-1.html
都试过了没用
页:
[1]