学习学习
jsm 发表于 2017-4-26 09:01
fastboot.bin以压缩文件删除后面的rar
请教，我的cm101s， 用hitool刷了分区文件，fastboot，recovery，system（原机备份）
但是还是启动不了，黑屏
putty 跑的结果如下， 请帮忙看看
Bootrom start
Boot from eMMC
Starting fastboot ...
System startup
DDRS
Reg Version:v1.1.0
Reg Time: 2016/7/6 15:22:53
Reg Name: hi3798mdmo1g_hi3798mv100_ddr3_1gbyte_16bitx2_4layers_8Q40E_emmc.reg
Jump to DDR
Fastboot 3.3.0 (liuyunlei@server180) (Jul 06 2016 - 15:37:08)
Fastboot: Version 3.3.0
Build Date: Jul6 2016, 15:38:08
CPU: Hi3798Mv100
Boot Media: eMMC
DDR Size: 1GB
Check nand flash controller v610. found
Special NAND id table Version 1.36
Nand ID: 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
No NAND device found!!!
MMC/SD controller initialization.
MMC/SD Card:
MID: 0x70
Read Block:512 Bytes
Write Block: 512 Bytes
Chip Size: 7456M Bytes (High Capacity)
Name: "M3250"
Chip Type: MMC
Version: 4.0
Speed: 52000000Hz
Bus Width: 8bit
Boot Addr: 0 Bytes
HI_OTP_LockIdWord,327: ID_WORD have already been locked
SDK Version: HiSTBAndroidV600R001C00SPC064_v2016060803
begin
begin
partition addr :
BaseAddress:0x200000, DataSize:0x100000, offset:0x0, bytes:0xb10
cksum , ptable->checksum
data at 0xc7ce is ok
BaseAddress:0x300000, DataSize:0x100000, offset:0x0, bytes:0xb10
cksum , ptable->checksum
0 fastboot 0x000000000 0x000200000
1 partition 0x000200000 0x000200000
2 recovery 0x000400000 0x001000000
3 deviceinfo 0x001400000 0x000200000
4 baseparam 0x001600000 0x000800000
5 pqparam 0x001E00000 0x000800000
6 logo 0x002600000 0x000800000
7 fastplay 0x002E00000 0x002800000
8 boot 0x005600000 0x001000000
9 misc 0x006600000 0x000200000
10 factory 0x006800000 0x001800000
11 system 0x008000000 0x027000000
12 cache 0x02F000000 0x017C00000
13 backup 0x046C00000 0x017C00000
14 swdb 0x05E800000 0x003000000
15 userdata 0x061800000 0x081000000
ptable info:2M(fastboot),2M(partition),16M(recovery),2M(deviceinfo),8M(baseparam),8M(pqparam),8M(logo),40M(fastplay),16M(boot),2M(misc),24M(factory),624M(system),380M(cache),380M(backup),48M(swdb),2064M(userdata)
ok
begin
deviceinfo addr :
BaseAddress:0x1400000, DataSize:0x100000, offset:0x0, bytes:0x514
start...
ok,checksum:0x506d
data at 0x001400000 is ok
count: name: value:
count: name: value:
count: name: value:
count: name: value:
ok
BaseAddress:0x5600000, DataSize:0x100000, offset:0x0, bytes:0x2000
disable serial,use default cmdline:
get standard swstandard:1080i_50Hz g_auto_adp:0
bootargs:
sw_ir_detect_recovery begin500 count
sw_ir_detect_recovery ok
BaseAddress:0x6600000, DataSize:0x100000, offset:0x0, bytes:0x10000
boot normal!!!
bootimg now: mmc read 0 0x1FFFFC0 2b000 8000;bootimg 0x1FFFFC0
ok
SDK Version: HiSTBAndroidV600R001C00SPC064_v2016060803
Reserve Memory
Start Addr: 0xFFFE000
Bound Addr: 0x8D4A000
FreeAddr: 0xF8F9000
Alloc Block:Addr Size
0xFBFD000 4194304
0xF8FC000 3145728
0xF8F9000 8192
begin
open loader keyed
Press Ctrl+C to stop autoboot
MMC read: dev # 0, block # 176128, count 32768 ... 32768 blocks read: OK
87192416 Bytes/s
kernel@ ffffffff (-1 bytes)
ramdisk @ ffffffff (-1 bytes)
page size @ -1 bytes
当前单板flash与烧写分区中的flash貌似不一致
群主能把固件给我份吗？，加我qq371611271
@jsm
大神，请问一下救砖的时候hitool里的串口com要设置多少? 是在我的电脑又见查看连接usbttl后显示com几是几吗？我的好像com4。 还是都要设置com5?
还有板端配置里的ip地址要填写多少啊？ 电脑和机顶盒在同一个网络里，我不知道机顶盒的ip地址，已成砖了，这样的话怎么填写ip地址呢
下载下来的不是文件{znds5}{znds5}{znds5}
这个必须要支持你
高手在当贝啊！学习了
高手在当贝啊！学习了
cy0077 发表于 2017-5-2 09:03
recovery.img解压出错
怎样才可以解压啊？