求救砖 付费 江苏移动创维E900V21C
本帖最后由 jiyong123 于 2017-12-21 12:17 编辑@hao501802766
前两天刚刚把刷机心得（2017年12月 江苏移动创维E900V21C刷机成功）和大家分享了。由于彻底关机后再开机，WIFI需要手动连接，觉得是固件版本的问题，昨晚重新试了《乐天20170828版-卡刷包》，刷完盒子重启，盒子就再也没亮起来了，电视直接什么图像都没有。
换了2台电脑，3条USB线， 2条TTL线（CH341线，PL2303线）
故障现象：
1、通电后，主板上PWR主电源灯亮一下绿灯就变红了；LAN网口灯一直红灯；IR遥控灯一直是熄灭状态。
2、刷机软件USB_Burning_Tool，一直发现不了盒子，且反复开关都不识别。
3、TTL跑到一半就卡住了，怎么回车都没反应，试了很多次。
Starting kernel ...
uboot time: 2041271 us
[ 0.000000@0] Initializing cgroup subsys cpu
[ 0.000000@0] Initializing cgroup subsys cpuacct
[ 0.000000@0] Linux version 3.14.29-svn125577 (chenshouhui@ubuntu) (gcc version 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.09 - Linaro GCC 4.9-2014.09) ) #1 SMP PREEMPT Sat Mar 18 22:16:52 HKT 2017
[ 0.000000@0] CPU: armv71 Processor revision 4
[ 0.000000@0] bootconsole enabled
INFO: HDCP22 key read fail!
INFO: p1d 0
INFO: pd1 0
4、TTL完整信息在2楼
GXL:BL1:9ac50e:a1974b;FEAT:ADFC318C;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 101949
BL2 Built : 18:58:24, Oct 25 2016.
gxl gc9db010 - xiaobo.gu@droid05
set vcck to 1080 mv
set vddee to 1050 mv
Board ID = 2, adc=153
CPU clk: 1200MHz
2layers board, use ddr_set
DDR chl: Rank0+1 @ 720MHz - FAIL
DDR chl: Rank0 @ 720MHz - PASS
DQS-corr enabled
DDR scramble enabled
Rank0: 1024MB(auto)-2T-11
DataBus test pass!
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
Load bl30 from eMMC, src: 0x00010200, des: 0x01100000, size: 0x00007400
Load bl301 from eMMC, src: 0x00018200, des: 0x01200000, size: 0x00002000
Load bl31 from eMMC, src: 0x0001c200, des: 0x10100000, size: 0x00019400
Load bl33 from eMMC, src: 0x00038200, des: 0x01000000, size: 0x000a6200
NOTICE:BL3-1: v1.0(debug):959fdf0
NOTICE:BL3-1: Built : 15:01:44, Dec 29 2016
aml log : bl31 normal boot !
bl30: check_permit, count is 1
bl30: check_permit: ok!
chipid: ef be ad de d f0 ad ba ef be ad de not ES chip
efuse init ops = c2
efuse init hdcp = c, cf9=7
seINFcOu:r e t aBsLk3 -s1t:a rItn!it
ializing runhtiigmhetsaesvices
WARNING: No OPTEE provided by BL2 boot loader
ERROR: Error initializing runtime service opteed_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x1000000
INFO: BL3-1: Next image spsr = 0x3c9
U-Boot 2015.01-svn125577 (Mar 18 2017 - 21:47:22)
DRAM:1 GiB
Relocation Offset is: 36ecf000
gpio: pin GPIODV_24 (gpio 43) value is 0
gpio: pin GPIOAO_3 (gpio 103) value is 1
mwm 0xc8837004: with ok
mwm 0xc883700c: with ok
mwm 0xc8837010: with ok
mwm 0xc8837010: with ok
register usb cfg = 0000000037f63db0
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
boot_device_flag : 1
Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
init bus_cycle=6, bus_timing=7, system=5.0ns
reset failed
get_chip_type and ret:fffffffe
get_chip_type and ret:fffffffe
chip detect failed and ret:fffffffe
nandphy_init failed and ret=0xfffffff1
MMC: aml_priv->desc_buf = 0x0000000033ebfdb0
aml_priv->desc_buf = 0x0000000033ec20d0
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x1ff2800
emmc/sd response timeout, cmd55, status=0x1ff2800
mmc refix success
mmc init success
overide_emmc_partition_table: overide cache
skip partition cache.
mmc read lba=0x12000, blocks=0x2
mmc read lba=0x12002, blocks=0x2
mmc_read_partition_tbl: mmc read partition OK!
eMMC/TSD partition table have been checked OK!
mmc env offset: 0x27400000
In: serial
Out: serial
Err: serial
board id is : 2
hpd_state=1
is invalid for cvbs.
set hdmitx VIC = 19
config HPLL = 2972
HPLL: 0xc000027b
config HPLL done
j = 2vid_clk_div = 1
hdmitx phy setting done
hdmitx: set enc for VIC: 19
enc_vpu_bridge_reset
rx version is 1.4 or belowdiv=10
To run cmd
read emmc dtb
dwmac.c9410000
Error: dwmac.c9410000 address not set.
wipe_data=successful
wipe_cache=successful
upgrade_step=2
reboot_mode=cold_boot
canvas init
addr=0x3d800000 width=5760, height=2160
ERR: 24 bit/pixel mode, but BMP has 16 bit/pixel
amlkey_init() enter!
keynum is 4
: tee size: 0
amlkey_issecure() 138: ret 1
amlkey_size() 162: ret 1
Error:fL301:key not programed yet
Error:fL682:mac key read fail
don't use random mac produce in uboot
IR init done!
gpio: pin GPIOH_6 (gpio 55) value is 1
Hit any key to stop autoboot:0
ee_gate_off ...
## Booting Android Image at 0x01080000 ...
reloc_addr =33f44bc0
copy done
Single dtb detected
load dtb from 0x1000000 ......
Uncompressing Kernel Image ... OK
kernel loaded at 0x01080000, end = 0x02033200
Loading Ramdisk to 33c36000, end 33ebca00 ... OK
Loading Device Tree to 000000001fff3000, end 000000001ffff3a1 ... OK
Starting kernel ...
uboot time: 2041271 us
[ 0.000000@0] Initializing cgroup subsys cpu
[ 0.000000@0] Initializing cgroup subsys cpuacct
[ 0.000000@0] Linux version 3.14.29-svn125577 (chenshouhui@ubuntu) (gcc version 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.09 - Linaro GCC 4.9-2014.09) ) #1 SMP PREEMPT Sat Mar 18 22:16:52 HKT 2017
[ 0.000000@0] CPU: armv71 Processor revision 4
[ 0.000000@0] bootconsole enabled
INFO: HDCP22 key read fail!
INFO: p1d 0
INFO: pd1 0
jiyong123 发表于 2017-12-21 12:09
GXL:BL1:9ac50e:a1974b;FEAT:ADFC318C;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 101949
用双头USB 重刷这个包：https://www.znds.com/rom/20132.html hao501802766 发表于 2017-12-21 12:39
用双头USB 重刷这个包：https://www.znds.com/rom/20132.html
双头的线换了好几条了
刷机软件一直识别不到盒子 jiyong123 发表于 2017-12-21 12:44
双头的线换了好几条了
刷机软件一直识别不到盒子
盒子接通电源开机 然后马上插入USB 应该可以我是这样刷机操作基本都OK 我都是关机，插上USB，再插电源，不行！
按你的方法 连续测试了20次 还是不行！
软件发现不了盒子 那我也没好的办法了要么就选择寄过来 我试试看当然也不保证一定能弄好 hao501802766 发表于 2017-12-21 13:55
那我也没好的办法了要么就选择寄过来 我试试看当然也不保证一定能弄好 ...
可以的 江浙沪范围 发给你们很方便的 hao501802766 发表于 2017-12-21 13:55
那我也没好的办法了要么就选择寄过来 我试试看当然也不保证一定能弄好 ...
地址已收到，没权限发短消息。这里回复，明天发快递出去 @hao501802766
快递已发 申通402886040185
页:
[1]
2
