联通杰赛S65拆机TTL安装第三方软件教程
这个盒子大部分地区都可以直接使用TV盒子助手安装软件，我手里的是重庆版的盒子并不能用此方法，所以就拆机TTL，以下是流程，仅供参考{:142:}准备工作：U盘、TTL线、螺丝刀、putty
当贝市场：https://webapk.dangbei.net/update/dangbeimarket.apk
当贝桌面：http://www.dangbei.com/zhuomian/
putty：http://www.tvapk.com/android/bangongshangwu/14141.htm
注：当贝市场和当贝桌面下载到U盘后，分别修改文件名“dangbei1”"dangbei2"
1、首先用螺丝刀拧下螺丝，拆开机器的外壳，将TTL线接好插在电脑USB接口上，接法如下图：
2、插入tll线的USB接口到电脑之后，需要大家先安装ttl的驱动，驱动安装完成之后，右键我的电脑——属性——设备管理器——端口——COM"X"（X就是最后位数字）——属性——端口设置——改为“115200”——确定；
**** Hidden Message *****
4、启动当贝桌面后，就可以进入当贝市场从里面下载自己所需要的软件了；
我的是贵州联通送的杰赛S65的机顶盒，安装的人说要接有线的才可以，我嫌麻烦，一直没有，我就想用wifi看，结果不能安装第三方软件，经过论坛查看，通过U盘可以安装软件，但是要把apk后缀改成exe，插上U盘，按遥控器上的菜单，进去就可以看见U盘，然后安装当贝桌面，然后进入当贝桌面设置以后就是当贝桌面为默认桌面，如果按遥控器主页无法进当贝桌面重启一下即可，安装当贝以后就可以随便安装第三方软件了，不受网络控制，任何网络就可以正常使用，不需要刷机，很方便的 正需要啊，感谢楼主无私分享！ {znds6}{znds6}楼主用心了谢谢分享 精华内容，楼主V5！ 学习学习！ 小手一抖，金币拿走。 正需要啊，感谢楼主无私分享！ 小手一抖，金币拿走。 小手一抖，金币拿走。 淡定，淡定，淡定…… 正需要啊，感谢楼主无私分享！ 淡定，淡定，淡定…… 自顶~ 强烈支持楼主ing……{znds6}{znds6}{znds6} 昂风格画 联通杰赛S65 拆机TTL破解 安装不成功 显示：apks is not valid! 联通杰赛S65 拆机TTL破解 安装不成功 显示：apks is not valid! 联通杰赛S65 拆机TTL破解 安装不成功 显示：apks is not valid! 联通杰赛S65 拆机TTL破解 安装不成功 显示：apks is not valid!
重庆联通4K 盒子S65-M2
本帖最后由 lyg2033 于 2018-3-26 21:06 编辑重庆联通4K 盒子S65-M2
以此教程:https://www.znds.com/jc/article/13991
USB/TTL连接：安装不了？？？？？？
GXL:BL1:9ac50e:a1974b;FEAT:ADFC318C;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 113896
BL2 Built : 01:56:32, Dec 22 2016.
gxl g1614c0b - xiaobo.gu@droid05
Board ID = 7, adc=514
set vcck to 1070 mv
set vddee to 1070 mv
CPU clk: 1200MHz
2layers board, use ddr_set
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 792MHz - FAIL
DDR3 chl: Rank0 @ 792MHz - PASS
Rank0: 1024MB(auto)-2T-11
DataBus test pass!
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x01100000, size: 0x00007400
Load bl301 from eMMC, src: 0x00018200, des: 0x01200000, size: 0x00002200
Load bl31 from eMMC, src: 0x0001c200, des: 0x10100000, size: 0x00019400
Load bl33 from eMMC, src: 0x00038200, des: 0x01000000, size: 0x00086400
NOTICE:BL3-1: v1.0(debug):959fdf0
NOTICE:BL3-1: Built : 15:01:44, Dec 29 2016
aml log : bl31 normal boot !
qiufang.dai@droid07]
bl30: check_permit, count is 1
bl30: check_permit: ok!
chipid: ef be ad de d f0 ad ba ef be ad de not ES chip
efuse init ops = e2
efuse init hdcp = c, cf9=7
sINFeOc:u r e tBaLs3k- 1s:t aIrnti!ti
alizing runtihmieg hs etrvices
WARNING: No OPTEE provided by BL2 boot loader
ERROR: Error initializing runtime service opteed_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x1000000
INFO: BL3-1: Next image spsr = 0x3c9
U-Boot 2015.01-gcae2519-dirty (Feb 12 2017 - 15:46:08)
DRAM:1 GiB
Relocation Offset is: 36eec000
gpio: pin GPIODV_24 (gpio 43) value is 1
mwm 0xc8837004: with ok
mwm 0xc883700c: with ok
mwm 0xc8837010: with ok
mwm 0xc8837010: with ok
register usb cfg = 0000000037f61090
canvas init
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
vpp: vpp_init
MMC: aml_priv->desc_buf = 0x0000000033edcac0
aml_priv->desc_buf = 0x0000000033edede0
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
mmc init success
mmc read lba=0x14000, blocks=0x400
Amlogic multi-dtb tool
Multi dtb detected
2layers board, board id use 7
Multi dtb tool version: v2 .
Support 6 dtbs.
aml_dt soc: gxl platform: p211 variant: 1g
dtb 0 soc: gxbb plat: p201 vari: 1g
dtb 1 soc: gxbb plat: p201 vari: 2g
dtb 2 soc: gxl plat: p211 vari: 1g
dtb 3 soc: gxl plat: p211 vari: 2g
dtb 4 soc: gxl plat: p215 vari: 1g
dtb 5 soc: gxl plat: p215 vari: 2g
Find match dtb: 2
start dts,buffer=0000000033ee1630,dt_addr=0000000033ef2e30
parts: 13
00: logo 0000000002000000 1
01:recovery 0000000002000000 1
02: rsv 0000000000800000 1
03: tee 0000000000800000 1
04: crypt 0000000002000000 1
05: misc 0000000002000000 1
06: instaboot 0000000020000000 1
07: boot 0000000002000000 1
08: system 0000000040000000 1
09: cache 0000000020000000 2
10: params 0000000004000000 2
11: bootfiles 0000000020000000 2
12: data ffffffffffffffff 4
get_dtb_struct: Get emmc dtb OK!
overide_emmc_partition_table: overide cache
skip partition cache.
Partition table get from SPL is :
name offset size flag
================================================================================ ===
0: bootloader 0 400000 0
1: reserved 2400000 4000000 0
2: cache 6c00000 20000000 2
3: env 27400000 800000 0
4: logo 28400000 2000000 1
5: recovery 2ac00000 2000000 1
6: rsv 2d400000 800000 1
7: tee 2e400000 800000 1
8: crypt 2f400000 2000000 1
9: misc 31c00000 2000000 1
10: instaboot 34400000 20000000 1
11: boot 54c00000 2000000 1
12: system 57400000 40000000 1
13: params 97c00000 4000000 2
14: bootfiles 9c400000 20000000 2
15: data bcc00000 115400000 4
mmc read lba=0x12000, blocks=0x2
mmc read lba=0x12002, blocks=0x2
mmc_read_partition_tbl: mmc read partition OK!
eMMC/TSD partition table have been checked OK!
mmc env offset: 0x27400000
In: serial
Out: serial
Err: serial
board id is : 7
hpd_state=1
is invalid for cvbs.
set hdmitx VIC = 4
config HPLL = 2970
HPLL: 0xc000027b
config HPLL done
j = 2vid_clk_div = 1
hdmitx: set enc for VIC: 4
HDMITX-DWC addr=0x10004006 rd_data=0x40
Error: HDMITX-DWC exp_data=0xff mask=0x9f
enc_vpu_bridge_reset
hdmitx phy setting done
div40 = 0
To run cmd
read emmc dtb
Amlogic multi-dtb tool
Multi dtb detected
Multi dtb tool version: v2 .
Support 6 dtbs.
aml_dt soc: gxl platform: p211 variant: 1g
dtb 0 soc: gxbb plat: p201 vari: 1g
dtb 1 soc: gxbb plat: p201 vari: 2g
dtb 2 soc: gxl plat: p211 vari: 1g
dtb 3 soc: gxl plat: p211 vari: 2g
dtb 4 soc: gxl plat: p215 vari: 1g
dtb 5 soc: gxl plat: p215 vari: 2g
Find match dtb: 2
Net: dwmac.c9410000
wipe_data=successfulSecd
wipe_cache=successful
bmp pixel: 16
addr=0x3d800000 width=2560, height=1440
upgrade_step=2
amlkey_init() enter!
keynum is 4
: tee size: 0
Error:fL507:key not programed yet
gpio: pin GPIOAO_2 (gpio 102) value is 1
rebootmode=cold_boot
Hit any key to stop autoboot:0
ee_gate_off ...
## Booting Android Image at 0x01080000 ...
reloc_addr =33f09250
copy done
Amlogic multi-dtb tool
Single dtb detected
load dtb from 0x1000000 ......
Uncompressing Kernel Image ... OK
kernel loaded at 0x01080000, end = 0x01f57020
Loading Ramdisk to 33c6c000, end 33ed9b21 ... OK
Loading Device Tree to 000000001fff3000, end 000000001ffff41a ... OK
signature:
fdt_instaboot: get header err
Starting kernel ...
uboot time: 2142576 us
[ 0.000000@0] Initializing cgroup subsys cpu
[ 0.000000@0] Initializing cgroup subsys cpuacct
[ 0.000000@0] Linux version 3.14.29-svn662 (hej@gci2017-Super-Server) (gcc ve rsion 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.09 - Lina ro GCC 4.9-2014.09) ) #1 SMP PREEMPT Fri Jan 19 01:20:29 CST 2018
[ 0.000000@0] CPU: armv71 Processor revision 4
[ 0.000000@0] bootconsole enabled
get_dvfs_info 0007
INFO: HDCP22 key read fail!
INFO: p1d 0
INFO: pd1 0
root@p201_iptv:/ # start adbd
root@p201_iptv:/ # df
Filesystem Size Used Free Blksize
/dev 425.8M 128.0K 425.7M 4096
/sys/fs/cgroup 425.8M 12.0K 425.8M 4096
/mnt/asec 425.8M 0.0K 425.8M 4096
/mnt/obb 425.8M 0.0K 425.8M 4096
/tmp 425.8M 1.8M 424.0M 4096
/tmp/playInfoLog 425.8M 0.0K 425.8M 4096
/tmp/capture 425.8M 0.0K 425.8M 4096
/tmp/begininfo 425.8M 0.0K 425.8M 4096
/tmp/collectinfo 425.8M 0.0K 425.8M 4096
/tmp/picinfo 425.8M 0.0K 425.8M 4096
/storage/external_storage 425.8M 0.0K 425.8M 4096
/system 991.9M 431.8M 560.1M 4096
/data 4.2G 151.0M 4.0G 4096
/cache 495.9M 644.0K 495.3M 4096
/params 59.0M 40.0K 58.9M 4096
/bootfiles 495.9M 384.0K 495.6M 4096
/mnt/shell/emulated 4.1G 151.0M 4.0G 4096
/swap_zram0 484.3M 20.0K 484.3M 4096
/storage/external_storage/sda1 1.9G 520.6M 1.4G 4096
root@p201_iptv:/ # cd /storage/external_storage/sda1
root@p201_iptv:/storage/external_storage/sda1 # ls
Android
dbsc.apk
dbzm.apk
root@p201_iptv:/storage/external_storage/sda1 # pm install dbsc.apk
pkg: dbsc.apk
apks is not valid!
root@p201_iptv:/storage/external_storage/sda1 # pm install dbzm.apk
pkg: dbzm.apk
apks is not valid!
安装不了？？？？？？？？？？？？？？？
以此教程:https://www.znds.com/jc/article/13991
USB/TTL连接：安装不了？？？？？？
GXL:BL1:9ac50e:a1974b;FEAT:ADFC318C;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 113896
BL2 Built : 01:56:32, Dec 22 2016.
gxl g1614c0b - xiaobo.gu@droid05
Board ID = 7, adc=514
set vcck to 1070 mv
set vddee to 1070 mv
CPU clk: 1200MHz
2layers board, use ddr_set
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 792MHz - FAIL
DDR3 chl: Rank0 @ 792MHz - PASS
Rank0: 1024MB(auto)-2T-11
DataBus test pass!
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x01100000, size: 0x00007400
Load bl301 from eMMC, src: 0x00018200, des: 0x01200000, size: 0x00002200
Load bl31 from eMMC, src: 0x0001c200, des: 0x10100000, size: 0x00019400
Load bl33 from eMMC, src: 0x00038200, des: 0x01000000, size: 0x00086400
NOTICE:BL3-1: v1.0(debug):959fdf0
NOTICE:BL3-1: Built : 15:01:44, Dec 29 2016
aml log : bl31 normal boot !
qiufang.dai@droid07]
bl30: check_permit, count is 1
bl30: check_permit: ok!
chipid: ef be ad de d f0 ad ba ef be ad de not ES chip
efuse init ops = e2
efuse init hdcp = c, cf9=7
sINFeOc:u r e tBaLs3k- 1s:t aIrnti!ti
alizing runtihmieg hs etrvices
WARNING: No OPTEE provided by BL2 boot loader
ERROR: Error initializing runtime service opteed_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x1000000
INFO: BL3-1: Next image spsr = 0x3c9
U-Boot 2015.01-gcae2519-dirty (Feb 12 2017 - 15:46:08)
DRAM:1 GiB
Relocation Offset is: 36eec000
gpio: pin GPIODV_24 (gpio 43) value is 1
mwm 0xc8837004: with ok
mwm 0xc883700c: with ok
mwm 0xc8837010: with ok
mwm 0xc8837010: with ok
register usb cfg = 0000000037f61090
canvas init
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
vpp: vpp_init
MMC: aml_priv->desc_buf = 0x0000000033edcac0
aml_priv->desc_buf = 0x0000000033edede0
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
mmc init success
mmc read lba=0x14000, blocks=0x400
Amlogic multi-dtb tool
Multi dtb detected
2layers board, board id use 7
Multi dtb tool version: v2 .
Support 6 dtbs.
aml_dt soc: gxl platform: p211 variant: 1g
dtb 0 soc: gxbb plat: p201 vari: 1g
dtb 1 soc: gxbb plat: p201 vari: 2g
dtb 2 soc: gxl plat: p211 vari: 1g
dtb 3 soc: gxl plat: p211 vari: 2g
dtb 4 soc: gxl plat: p215 vari: 1g
dtb 5 soc: gxl plat: p215 vari: 2g
Find match dtb: 2
start dts,buffer=0000000033ee1630,dt_addr=0000000033ef2e30
parts: 13
00: logo 0000000002000000 1
01:recovery 0000000002000000 1
02: rsv 0000000000800000 1
03: tee 0000000000800000 1
04: crypt 0000000002000000 1
05: misc 0000000002000000 1
06: instaboot 0000000020000000 1
07: boot 0000000002000000 1
08: system 0000000040000000 1
09: cache 0000000020000000 2
10: params 0000000004000000 2
11: bootfiles 0000000020000000 2
12: data ffffffffffffffff 4
get_dtb_struct: Get emmc dtb OK!
overide_emmc_partition_table: overide cache
skip partition cache.
Partition table get from SPL is :
name offset size flag
================================================================================ ===
0: bootloader 0 400000 0
1: reserved 2400000 4000000 0
2: cache 6c00000 20000000 2
3: env 27400000 800000 0
4: logo 28400000 2000000 1
5: recovery 2ac00000 2000000 1
6: rsv 2d400000 800000 1
7: tee 2e400000 800000 1
8: crypt 2f400000 2000000 1
9: misc 31c00000 2000000 1
10: instaboot 34400000 20000000 1
11: boot 54c00000 2000000 1
12: system 57400000 40000000 1
13: params 97c00000 4000000 2
14: bootfiles 9c400000 20000000 2
15: data bcc00000 115400000 4
mmc read lba=0x12000, blocks=0x2
mmc read lba=0x12002, blocks=0x2
mmc_read_partition_tbl: mmc read partition OK!
eMMC/TSD partition table have been checked OK!
mmc env offset: 0x27400000
In: serial
Out: serial
Err: serial
board id is : 7
hpd_state=1
is invalid for cvbs.
set hdmitx VIC = 4
config HPLL = 2970
HPLL: 0xc000027b
config HPLL done
j = 2vid_clk_div = 1
hdmitx: set enc for VIC: 4
HDMITX-DWC addr=0x10004006 rd_data=0x40
Error: HDMITX-DWC exp_data=0xff mask=0x9f
enc_vpu_bridge_reset
hdmitx phy setting done
div40 = 0
To run cmd
read emmc dtb
Amlogic multi-dtb tool
Multi dtb detected
Multi dtb tool version: v2 .
Support 6 dtbs.
aml_dt soc: gxl platform: p211 variant: 1g
dtb 0 soc: gxbb plat: p201 vari: 1g
dtb 1 soc: gxbb plat: p201 vari: 2g
dtb 2 soc: gxl plat: p211 vari: 1g
dtb 3 soc: gxl plat: p211 vari: 2g
dtb 4 soc: gxl plat: p215 vari: 1g
dtb 5 soc: gxl plat: p215 vari: 2g
Find match dtb: 2
Net: dwmac.c9410000
wipe_data=successfulSecd
wipe_cache=successful
bmp pixel: 16
addr=0x3d800000 width=2560, height=1440
upgrade_step=2
amlkey_init() enter!
keynum is 4
: tee size: 0
Error:fL507:key not programed yet
gpio: pin GPIOAO_2 (gpio 102) value is 1
rebootmode=cold_boot
Hit any key to stop autoboot:0
ee_gate_off ...
## Booting Android Image at 0x01080000 ...
reloc_addr =33f09250
copy done
Amlogic multi-dtb tool
Single dtb detected
load dtb from 0x1000000 ......
Uncompressing Kernel Image ... OK
kernel loaded at 0x01080000, end = 0x01f57020
Loading Ramdisk to 33c6c000, end 33ed9b21 ... OK
Loading Device Tree to 000000001fff3000, end 000000001ffff41a ... OK
signature:
fdt_instaboot: get header err
Starting kernel ...
uboot time: 2142576 us
[ 0.000000@0] Initializing cgroup subsys cpu
[ 0.000000@0] Initializing cgroup subsys cpuacct
[ 0.000000@0] Linux version 3.14.29-svn662 (hej@gci2017-Super-Server) (gcc ve rsion 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.09 - Lina ro GCC 4.9-2014.09) ) #1 SMP PREEMPT Fri Jan 19 01:20:29 CST 2018
[ 0.000000@0] CPU: armv71 Processor revision 4
[ 0.000000@0] bootconsole enabled
get_dvfs_info 0007
INFO: HDCP22 key read fail!
INFO: p1d 0
INFO: pd1 0
root@p201_iptv:/ # start adbd
root@p201_iptv:/ # df
Filesystem Size Used Free Blksize
/dev 425.8M 128.0K 425.7M 4096
/sys/fs/cgroup 425.8M 12.0K 425.8M 4096
/mnt/asec 425.8M 0.0K 425.8M 4096
/mnt/obb 425.8M 0.0K 425.8M 4096
/tmp 425.8M 1.8M 424.0M 4096
/tmp/playInfoLog 425.8M 0.0K 425.8M 4096
/tmp/capture 425.8M 0.0K 425.8M 4096
/tmp/begininfo 425.8M 0.0K 425.8M 4096
/tmp/collectinfo 425.8M 0.0K 425.8M 4096
/tmp/picinfo 425.8M 0.0K 425.8M 4096
/storage/external_storage 425.8M 0.0K 425.8M 4096
/system 991.9M 431.8M 560.1M 4096
/data 4.2G 151.0M 4.0G 4096
/cache 495.9M 644.0K 495.3M 4096
/params 59.0M 40.0K 58.9M 4096
/bootfiles 495.9M 384.0K 495.6M 4096
/mnt/shell/emulated 4.1G 151.0M 4.0G 4096
/swap_zram0 484.3M 20.0K 484.3M 4096
/storage/external_storage/sda1 1.9G 520.6M 1.4G 4096
root@p201_iptv:/ # cd /storage/external_storage/sda1
root@p201_iptv:/storage/external_storage/sda1 # ls
Android
dbsc.apk
dbzm.apk
root@p201_iptv:/storage/external_storage/sda1 # pm install dbsc.apk
pkg: dbsc.apk
apks is not valid!
root@p201_iptv:/storage/external_storage/sda1 # pm install dbzm.apk
pkg: dbzm.apk
apks is not valid!
安装不了？？？？？？？？？？？？？？？
重庆版的盒子 联通杰赛S65拆机TTL root@p201_iptv:/storage/external_storage/sda1 # pm install dbsc.apk pkg: dbsc.apk apks is not valid! root@p201_iptv:/storage/external_storage/sda1 # pm install dbzm.apk pkg: dbzm.apk apks is not valid! 安装不了？？？？？？？？？？？？？？？ 重庆版的盒子 联通杰赛S65拆机TTL root@p201_iptv:/storage/external_storage/sda1 # pm install dbsc.apk pkg: dbsc.apk apks is not valid! root@p201_iptv:/storage/external_storage/sda1 # pm install dbzm.apk pkg: dbzm.apk apks is not valid! 安装不了？？？？？？？？？？？？？？？ 重庆版的盒子 联通杰赛S65拆机TTL root@p201_iptv:/storage/external_storage/sda1 # pm install dbsc.apk pkg: dbsc.apk apks is not valid! root@p201_iptv:/storage/external_storage/sda1 # pm install dbzm.apk pkg: dbzm.apk apks is not valid! 安装不了？？？？？？？？？？？？？？？ 重庆版的盒子 联通杰赛S65拆机TTL
root@p201_iptv:/storage/external_storage/sda1 # pm install dbsc.apk
pkg: dbsc.apk
apks is not valid!
root@p201_iptv:/storage/external_storage/sda1 # pm install dbzm.apk
pkg: dbzm.apk
apks is not valid!
安装不了？？？？？？？？？？？？？？？