IP903H用rs232线开adb碰到问题
本帖最后由 山阴路的夏天 于 2018-3-7 20:04 编辑rs232线连电脑和盒子，开启ADB装当贝市场，碰到问题。
练好了，接通电源后，PUTTY，一直跑，跑了一长串，等他停下来，按 回车 的时候没反应，也没有出现大家说的 #，无法输入 start adbd，求助大神，如何解决？
我的信息如下：
----------------------------------
HELLO! BOOT0 is starting!
boot0 version : 4.2.0
fel_flag = 0x00000000
rtc value = 0x00000000
rtc value = 0x00000000
rtc value = 0x00000000
rtc value = 0x00000000
rtc value = 0x00000000
rtc value = 0x00000000
rtc value = 0x00000000
rtc value = 0x00000000
DRAM DRIVE INFO: V0.8
DRAM Type = 3 (2:DDR2,3:DDR3,6:LPDDR2,7:LPDDR3)
DRAM CLK = 576 MHz
DRAM zq value: 003b3bfb
READ DQS LCDL = 00212121
DRAM SIZE =1024 M
odt delay
dram size =1024
card boot number = 2
card no is 2
sdcard 2 line count 8
: mmc driver ver 2014-12-10 21:20:39
: ***Try SD card 2***
: mmc 2 cmd 8 err 00000100
: mmc 2 cmd 8 err 00000100
: mmc 2 send if cond failed
: mmc 2 cmd 55 err 00000100
: mmc 2 cmd 55 err 00000100
: mmc 2 send app cmd failed
: ***Try MMC card 2***
: 8bit ddr!!!
: MMC ver 4.0
: SD/MMC Card: 8bit, capacity: 7456MB
: vendor: Man 00110100 Snr 00f2ac0e
: product: 008G3
: revision: 3.0
: ***SD/MMC 2 init OK!!!***
sdcard 2 init ok
The size of uboot is 000dc000.
sum=0038cae7
src_sum=0038cae7
set_mmc_para,sdly 50M 0
set_mmc_para,sdly 25M 0
Succeed in loading uboot from sdmmc flash.
Ready to disable icache.
Jump to secend Boot.
SUNXI_NORMAL_MODE
[ 0.269]e mode
U-Boot 2011.09-rc1 (Dec 02 2016 - 16:10:58) Allwinner Technology
[ 0.276]version: 1.1.0
normal mode
[ 0.284]pmbus: ready
not set main pmu id
axp_probe error
[ 0.320]PMU: pll1 1008 Mhz,PLL6=600 Mhz
AXI=336 Mhz,AHB=200 Mhz, APB1=100 Mhz
sid read already
fel key new mode
run key detect
no key found
no key input
dram_para_set start
dram_para_set end
normal mode
[ 0.351]DRAM:1 GiB
relocation Offset is: 35af6000
read rtc = 0x0
mag be start_type no use
user_gpio config
user_gpio ok
gic: normal or no secure os mode
workmode = 0
MMC: 2
[ 0.430]: mmc driver ver 2016-03-24 19:30:15
[ 0.435]: get sdc_phy_wipe fail.
[ 0.439]: get sdc0 sdc_erase fail.
[ 0.443]: get sdc_2xmode ok, val = 1
[ 0.447]: get sdc_ddrmode ok, val = 1
[ 0.451]: get sdc_f_max fail,use default50000000Hz
[ 0.457]: get card_line ok, card_line = 8
[ 0.461]: get sdc_ex_dly_used fail,use default
[ 0.466]: SUNXI SD/MMC: 2
[ 0.471]: mmc_config_clock: clk 400000
[ 0.486]: *Try SD card 2*
[ 0.491]: mmc 2 cmd 8 err 100
[ 0.497]: mmc send if cond failed
[ 0.502]: mmc 2 cmd 55 err 100
[ 0.508]: send app cmd failed
[ 0.511]: *Try MMC card 2*
[ 0.578]: mmc_config_clock: clk 25000000
[ 0.592]: mmc re-update_phase
[ 0.599]: mmc re-update_phase
[ 0.606]: mmc re-update_phase
[ 0.612]: ddr8
[ 0.616]: mmc re-update_phase
[ 0.624]: mmc_config_clock: clk 25000000
[ 0.634]: mmc_config_clock: clk 50000000
[ 0.642]: CID 0x11010030 0x30384733 0x3000f2ac 0xe7283a5
[ 0.647]: MMC v5.1
[ 0.650]: mmc clk 50000000
[ 0.653]: SD/MMC Card: 8bit, capacity: 7456MB
[ 0.658]: boot0 capacity: 4000KB,boot1 capacity: 4000KB
[ 0.664]: ***SD/MMC 2 init OK!!!***
[ 0.670]: erase_grp_size:0x400WrBlk * 0x200 = 0x80000 Byte
[ 0.676]: secure_feature 0x55
[ 0.680]: secure_removal_type0x39
[ 0.684]sunxi flash init ok
script config pll_de to 864 Mhz
Not Found clk pll_video1 in script
script config pll_video to 297 Mhz
disp_init_tv
disp_init_tv enter g_tv_used
screen 0 do not support TV TYPE!
disp tv device_registered
unable to find regulator vcc-hdmi-18 from or
enable power vcc-hdmi-18, ret=-1
DRV_DISP_Init end
error: open tv_vdid.fex, maybe it is not exist
save_vendor_id=,value = 0
read byte = 10
= 40a
read byte = 10
= 20b
boot_disp.auto_hpd=1
auto hpd check has 100 times!
auto check no any connected, the output_type is 2
attched ok, mgr1<-->device1, type=2, mode=11----
ready to set mode
disp_tv_enable
[ 2.106]finally, output_type=0x2, output_mode=0xb, screen_id=0x1, disp_para=0x20b0000
In: serial
Out: serial
Err: serial
--------fastboot partitions--------
-total partitions:14-
-name- -start- -size-
bootloader: 1000000 1000000
env : 2000000 1000000
boot : 3000000 1000000
system : 4000000 30000000
misc : 34000000 1000000
recovery : 35000000 2000000
sysrecovery : 37000000 30000000
private : 67000000 1000000
Reserve0 : 68000000 1000000
klog : 69000000 1000000
Reserve1 : 6a000000 2000000
Reserve2 : 6c000000 1000000
cache : 6d000000 28000000
UDISK : 95000000 0
-----------------------------------
base bootcmd=run setargs_nand boot_normal
bootcmd set setargs_mmc
key 0
cant find rcvy value
cant find fstbt value
misc partition found
to be run cmd=run setargs_mmc boot_normal
read item0 copy0
the secure storage item0 copy0 is good
name in map mac
the secure storage item2 copy0 is good
Don't need to decrypt object
updataed mac = AC:4A:FE:C4:48:30
no item name wifi_mac in the map
sunxi storage read fail
no item name bt_mac in the map
sunxi storage read fail
name in map specialstr
the secure storage item3 copy0 is good
Don't need to decrypt object
updataed specialstr = 004602FF002800400004AC4AFEC44830
no item name serialno in the map
sunxi storage read fail
check user data form private
WORK_MODE_BOOT
adver not need show
sunxi_bmp_logo_display
f_read btr over hd12896
read byte = 3686456
[ 2.352]screen_id =1, screen_width =720, screen_height =576
[ 2.358]frame buffer address 46400036
[ 2.362]Hit any key to stop autoboot:0
read boot or recovery all
[ 2.521]sunxi flash read :offset 3000000, 12924609 bytes OK
[ 2.529]ready to boot
board_display_setenv:disp_para=20b0000 init_disp=20b040a tv_vdid=0
[ 2.538]: mmc exit start
[ 2.542]: mmc_config_clock: clk 50000000
[ 2.550]: mmc_config_clock: clk 400000
[ 2.565]: mmc 2 cmd 8 err 100
[ 2.571]: mmc send if cond failed
[ 2.576]: mmc 2 cmd 55 err 100
[ 2.582]: send app cmd failed
[ 2.614]: get sdc_phy_wipe fail.
[ 2.618]: get sdc0 sdc_erase fail.
[ 2.622]: get sdc_2xmode ok, val = 1
[ 2.626]: get sdc_ddrmode ok, val = 1
[ 2.630]: get sdc_f_max fail,use default50000000Hz
[ 2.636]: get card_line ok, card_line = 8
[ 2.640]: get sdc_ex_dly_used fail,use default
[ 2.645]: mmc 2 exit ok
[ 2.648]
Starting kernel ...
: From boot, get meminfo:
Start:0x40000000
Size: 1024MB
ion_carveout reserve: 160m@0 312m@0 130m@1 200m@1
ion_reserve_common: ion reserve: !
你解决这个问题了吗？我的也到这里了！
页:
[1]
