四川B860A ZTV801113P0007 砖了 怎么救
固件版本为ZTV801113P0007对应机顶盒硬件版本为IBHR-ANDROIDSTBGA-068
Recovery版本V801014
Uboot：V0025
配置版本：V20150624
logo v801006
根据网上的一键ROOT方法 用ABD进行破解，结果机顶盒成砖了，只停在启动界面，后来在网上找了 教程 如下
必须找到这三个文件
ota.zip
u-boot-aml-ucl.bin
uImage_recovery
参照什么的方法TTL分别刷入，指令：
m8m2_n200_v1#sdc_update bootloader u-boot-aml-ucl.bin
m8m2_n200_v1#sdc_update recovery uImage_recovery
重新启动盒子
m8m2_n200_v1#safe 这个不很重要，否则会提示错误not defined
完成之后提示符变为#重新刷的话按回车+ctrl键多次进入#
#recovery --update_package=/sdcard/ota.zip
但这个方法也不行， 后来试了在OTA.ZIP中解包出 recovery.img和 system.img 放在SD中 输入以下两个命令也不行。
sdc_update recovery recovery.img恢复recovery,
还可以sdc_update system system.img
请问有高手吗，怎么解决这个问题。我以前备份了的ota.zip
u-boot-aml-ucl.bin
uImage_recovery 这三个文件。
现在盒子不断重启，提示发现新软件 正在升级 请勿断电 建议参考这个方法https://www.znds.com/tv-581030-1-2.html 试了 显示 Unable to read "recovery.img" from mmc 0:1 m8m2_n200_v1#
m8m2_n200_v1#sdc_update bootloader u-boot-aml-ucl.bin
sdio_detect return 1
SDIO Port B:0, if_type=7, initialized OK!
Device: SDIO Port B
Manufacturer ID: 0
OEM: 0
Name: ran Speed: 20000000
Rd Block Len: 512
SD version 2.0
High Capacity: Yes
Capacity: 3941597184
Boot Part Size: 0
Bus Width: 4-bit
fat:Filesize is 0x71690B
ERR(v2_common/optimus_simg2img.c)L60:sparse bad magic, expect 0xed26ff3a but 0xee15d177
u-boot-aml-ucl.bin is exist
msg:Down(store) part(bootloader) sz(0x71690) fmt(normal)
msg:totalSlotNum = 0, nextWriteBackSlot 8
fat:Filesize is 0x71690B
fat:sz 0x690 gz 0x1690, bps 0x1000
msg:Burn Start...
msg:Acs not in the spl of uboot_bin
mmc switch part boot0 success
mmc switch part boot1 success
mmc switch part user success
msg:Burn complete
BURN u-boot-aml-ucl.bin to part bootloader OK!
=====>Burn part bootloader in fmt normal OK<======
m8m2_n200_v1#sdc_update bootloader u-boot-aml-ucl.bin
Device: SDIO Port B
Manufacturer ID: 0
OEM: 0
Name: ran Speed: 20000000
Rd Block Len: 512
SD version 2.0
High Capacity: Yes
Capacity: 3941597184
Boot Part Size: 0
Bus Width: 4-bit
fat:Filesize is 0x71690B
ERR(v2_common/optimus_simg2img.c)L60:sparse bad magic, expect 0xed26ff3a but 0xee15d177
u-boot-aml-ucl.bin is exist
msg:Down(store) part(bootloader) sz(0x71690) fmt(normal)
msg:totalSlotNum = 0, nextWriteBackSlot 8
fat:Filesize is 0x71690B
fat:sz 0x690 gz 0x1690, bps 0x1000
msg:Burn Start...
msg:Acs not in the spl of uboot_bin
mmc switch part boot0 success
mmc switch part boot1 success
mmc switch part user success
msg:Burn complete
BURN u-boot-aml-ucl.bin to part bootloader OK!
=====>Burn part bootloader in fmt normal OK<======
m8m2_n200_v1#sdc_update recovery uImage_recovery
Device: SDIO Port B
Manufacturer ID: 0
OEM: 0
Name: ran Speed: 20000000
Rd Block Len: 512
SD version 2.0
High Capacity: Yes
Capacity: 3941597184
Boot Part Size: 0
Bus Width: 4-bit
fat:Filesize is 0xb42fc0B
ERR(v2_common/optimus_simg2img.c)L60:sparse bad magic, expect 0xed26ff3a but 0x52444e41
uImage_recovery is exist
msg:flash LOGIC partCap 0x1400000B
msg:Down(store) part(recovery) sz(0xb42fc0) fmt(normal)
msg:totalSlotNum = 0, nextWriteBackSlot 1
fat:Filesize is 0xb42fc0B
msg:Burn Start...
fat:sz 0xfc0 gz 0x2fc0, bps 0x1000
msg:Burn complete
BURN uImage_recovery to part recovery OK!
=====>Burn part recovery in fmt normal OK<======
m8m2_n200_v1#run recovery --update_package=/sdcard/ota.zip
enter recovery
Device: SDIO Port B
Manufacturer ID: 0
OEM: 0
Name: ran Speed: 20000000
Rd Block Len: 512
SD version 2.0
High Capacity: Yes
Capacity: 3941597184
Boot Part Size: 0
Bus Width: 4-bit
reading recovery.img
** Unable to read "recovery.img" from mmc 0:1 **
Secure kernel sz 0xb42fc0
Aml log : M8-R1024 IMG pass! 请问哪位大神 用什么方法解决 #
# recovery --update_package=/sdcard/ota.zip
I:loaded /etc/recovery.kl
I:recovery key map table
I:=========================
I:0 type:select value:-4 key:28 15 158 -1 -1 -1
I:1 type:down value:-3 key:108 114 109 -1 -1 -1
I:2 type:up value:-2 key:103 104 115 -1 -1 -1
I:3 type:back_door value:-6 key:128 26 118 -1 -1 -1
I:
enter recovery mode,run green led!
Language ==> Not found
MarketCode ==> Not found
OperatorsCode ==> Not found
E:market_code =-1
E:operators_code =-1
gr_init_font222: cwidth 32cheight35
can't open /dev/tty0: No such file or directory
framebuffer: fd 3 (1920 x 1080)
installing_text:(1 x 1 @ 1896)
erasing_text:(1 x 1 @ 1599)
no_command_text:(1 x 1 @ 1599)
error_text:(1 x 1 @ 1599)
XIEZHIJUN CheckLEDDevForCtrl
@@@@@=====>LEDCTRL_RUN_GREEN_OFF !
XIEZHIJUN CheckLEDDevForCtrl
@@@@@=====>LEDIR_IOCS_OFF !
XIEZHIJUN CheckLEDDevForCtrl
XIEZHIJUN CheckLEDDevForCtrl
@@@@@=====>LEDIR_IOCS_OFF !
XIEZHIJUN CheckLEDDevForCtrl
@@@@@=====>LEDIR_IOCS_OFF !
XIEZHIJUN CheckLEDDevForCtrl
@@@@@=====>LEDCTRL_RUN_GREEN_ON !
UpdateMode ==> Not found
发现新版软件,正在升级,勿断电,请稍候！
[ 9.203992@0] EXT4-fs error (device mmcblk1p9): ext4_validate_block_bitmap:368: comm recovery: bg 4: block 131072: invalid block bitmap
[ 9.204895@0] Aborting journal on device mmcblk1p9-8.
[ 9.205705@0] EXT4-fs (mmcblk1p9): Remounting filesystem read-only
[ 9.210732@2] Restarting system from safe_mode.
[ 9.212590@2] Restarting Linux version 3.10.33-svn48455 (yinjiandong@A23131934) (gcc version 4.7.3 20130205 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2013.02-01-20130221 - Linaro GCC 2013.02) ) #1 SMP PREEMPT Fri Oct 9 21:30:38 CST 2015
[ 9.212590@2]
[ 9.262540@2] arm_restart: Console was locked! Busting
QA9:A;SVN:74E;POC:17F;STS:0;BOOT:0;INIT:0;READ:0;CHECK:0;PASS:0;
no sdio debug board detected
从这上面开始进行重启了。
更新出现 这样有谁能帮忙啊 IBHR-ANDROIDSTBGA-068是高安版
那三个文件是从自己的盒子里备份的吗？ 是的 我的四川的,也是你那咱问题,直接卡刷system.img就行了.必须TTL