本帖最后由 qiweiv 于 2017-1-8 19:42 编辑
webpad 发表于 2017-1-7 18:33
上传一下USB burning tool的log，还有盒子TTL输出log
TTL是不是需要硬件设备啊?我这没有噢,大神帮忙看看,是不是刷不回来了啊,!!!
I/ Read config config_progress.xml
W/ Cpu: 0
W/ System: Microsoft Windows 7
W/ Tool version: v1.6.31
W/ Import upgrade file D:\USB-Burning-tool-v1.6.31\DIY\110777_Domy_HPHZ(DM1102)_factory_20150205.zip
I/ Global::deleteDir tmp\config_progress.xml ok
I/ Global::deleteDir tmp\recovery.img ok
I/ Global::deleteDir tmp\u-boot-orig.bin ok
I/ Global::deleteDir tmp\update.zip ok
I/ Global::deleteDir tmp\usb_spl.bin ok
I/ begin run
I/ tmp\
I/ config path is :
I/ Read config tmp\config_progress.xml
I/ Calc checksum: tmp\usb_spl.bin -> 7b202b2f
I/ Calc checksum: tmp\u-boot-orig.bin -> e0fcd61f
I/ Crc cmd: crc 0x8f800000 672180 e0fcd61f
I/ tmp\recovery.img modify uImage size is :5292032
I/ Calc checksum: tmp\recovery.img -> a6b950e3
I/ Crc cmd: crc 0x82000000 5292032 a6b950e3
I/ BurnThread(1) exit
Call system rescan
IOCTL_IDENTIFY_HOST_Handler ret=-31
reset worldcup device
Reset WorldCup Device
Call system rescan
Call system rescan
W/ Loading spl ...
I/ This chip is revD, write pll reg
W/ Transfer Complete! total size is 19244 Bytes
I/ run from ram:0xd9000000
I/ Loading uboot ...
I/ LoadUboot identify() return 8
W/ Transfer Complete! total size is 672180 Bytes
I/ load uboot succeed!
I/ Cmd --> (crc 0x8f800000 672180 e0fcd61f)
I/ <-- Crc check result(success)
I/ Run from ram(8f800000) idf(8)
I/ Finish run 0x8f800000
W/ After load uboot, disconnect,mBurnWaitCount: 9
W/ After load uboot, disconnect,mBurnWaitCount: 12
W/ wait uboot run ,scan system again!!!
W/ After load uboot, disconnect,mBurnWaitCount: 15
W/ After load uboot, disconnect,mBurnWaitCount: 18
W/ After load uboot, disconnect,mBurnWaitCount: 21
W/ After load uboot, disconnect,mBurnWaitCount: 24
W/ After load uboot, disconnect,mBurnWaitCount: 27
W/ After load uboot, disconnect,mBurnWaitCount: 30
W/ After load uboot, disconnect,mBurnWaitCount: 33
F/ wait uboot run failed 35 so make it disconnected
E/ failed because no connected device ,current step is 4
I/ BurnThread(1) exit
I/ saveLog 6430760
@webpad
我上传了一个diy线刷包，burn_bootloader试一下
qiweiv 发表于 2017-1-7 21:07
TTL是不是需要硬件设备啊?我这没有噢,大神帮忙看看,是不是刷不回来了啊,!!!
I/ Read config con ...
TTL连接需要一个usb转ttl小板设备，淘宝10元以内，看你主板TTL接口没有插座也没插针，还需要焊接。
升级到最新版本后，不好使了
webpad 发表于 2017-1-7 21:39
TTL连接需要一个usb转ttl小板设备，淘宝10元以内，看你主板TTL接口没有插座也没插针，还需要焊接。 ...
刷burn_bootloader还是一样的问题,看来真是砖了,大神推荐个ttl的型号,再推荐个性价比高的盒子,买一套,非常感谢大神的热心回复
谢谢，楼主！
qiweiv 发表于 2017-1-7 23:28
刷burn_bootloader还是一样的问题,看来真是砖了,大神推荐个ttl的型号,再推荐个性价比高的盒子,买一套,非 ...
我是用PL2303 可能质量较好，win7用着没问题， 据说CP2102更好些
短接的意思是接触一下就松开镊子，还是一直都连接1号和4号针脚？
强烈支持楼主ing……
burn_bootloader跟 burn_recovery多能100%过去，其他的多卡72%， TTL显示 EEEE
