数码视讯的S6,怎么安装第三方软件呢？
本帖最后由 山阴路的夏天 于 2018-3-8 14:33 编辑用ttl线接上后显示到start kenel就不动了，具体显示如下：
QA5:A;SVN:B72;POC:3FF;STS:0;BOOT:0;INIT:0;READ:0;CHECK:0;PASS:0;
no sdio debug board detected
TE : 24849
BT : 09:08:22 Jan 23 2016
PMU:NONE
##### VDDEE voltage = 0x044c
CPU clock is 792MHz
DDR mode: 32 bit mode
DDR size: 1GB (auto)
DDR check: Pass!
DDR clock: 636MHz with 2T mode
DDR pll bypass: Disabled
DDR init use : 16669 us
HHH
ucl decompress...pass
0x12345678
Boot from internal device 1st NAND
TE : 217181
System Started
U-boot-svn106907(m8b_m201_v1@04d619ce) (Jan 23 2016 - 09:08:11)
clr h-ram
DRAM:1 GiB
relocation Offset is: 2fec0000
show partition table:
part: 0, name : logo, size : 2000000
part: 1, name : recovery, size : 2000000
part: 2, name : misc, size : 2000000
part: 3, name : boot, size : 2000000
part: 4, name : system, size : 40000000
part: 5, name : cache, size : 20000000
part: 6, name : data, size : end
aml_card_type=0x200
MMC: add mmc dev_num=0, port=1, if_type=6
add mmc dev_num=1, port=2, if_type=6
SDIO Port B: 0, SDIO Port C: 1
power init
out reg=c110804c,value=dfffffff
IR init done!
register usb cfg = 3ff6f9b0
register usb cfg = 3ff726e8
init 32k clock
out reg=c8100024,value=bfff3fff
out reg=c8100024,value=bff73ffb
enter nand boot
NAND BOOT: boot_device_flag 1
Nand PHY driver Version: 1.01.001.0007 (c) 2013 Amlogic Inc.
amlnf_phy_init : amlnf init flag 5
NAND device id: 2c 44 44 4b a9 0 0 0
detect NAND device: D revision NAND 4GiB MT29F32G08CBADA
device_boot_flag=1
NAND BOOT: boot_device_flag 1
Nand PHY driver Version: 1.01.001.0007 (c) 2013 Amlogic Inc.
amlnf_phy_init : amlnf init flag 0
NAND device id: 2c 44 44 4b a9 0 0 0
detect NAND device: D revision NAND 4GiB MT29F32G08CBADA
AML_NAND_NEW_OOB : new oob
bus_cycle=6, bus_timing=8,system=3.9ns,flash->T_REA =16,flash->T_RHOH=15
NAND CKECK: arg nbbt: arg_valid= 1, valid_blk_addr = 5, valid_page_addr = 0
NAND CKECK: arg ncnf: arg_valid= 1, valid_blk_addr = 7, valid_page_addr = 0
NAND CKECK: arg nkey: arg_valid= 1, valid_blk_addr = 4, valid_page_addr = 3
i=0,register --- nand_key
NAND CKECK: arg nenv: arg_valid= 1, valid_blk_addr = 9, valid_page_addr = 27
nfboot : offset: 0x000000000000 -0x000000800000 : partitons 0 : single_chip single_plane
nfcache : offset: 0x000006800000 -0x000024800000 : partitons 1 : single_chip multi_plane
nfcode : offset: 0x00002b000000 -0x000050800000 : partitons 5 : single_chip multi_plane
nfdata : offset: 0x00007b800000 -0x000084800000 : partitons 1 : single_chip multi_plane
amlnf_logic_init: START
amlnf_logic_init:COMPLETE
NAND BOOT,nand_env_relocate_spec : env_relocate_spec 56
uboot env amlnf_env_read : ####
set_storage_device_flag: store 1
vpu clk_level = 3
set vpu clk: 182150000Hz, readback: 182150000Hz(0x701)
do_judgecheck argc: 5
argv: 2 argv: 4 argv: true argv: outputdefault
judgecheck - judgecheck 1 1 true/false command command
Usage:
judgecheck argv: <key> <value> <true/false> <command> <command>
hdmi tx power init
cvbs performance type = 1, table = 0
vdac open.0 = 0x1, 0x0
mode is: 4
viu chan = 1
config HPLL
config HPLL done
bmp pixel: 24
Multi dtb tool version: v2 .
Multi dtb detected, support 2 dtbs.
aml_dt soc: m8b platform: m201 variant: 1G
dtb 0 soc: m8b plat: m201 vari: 1G
dtb 1 soc: m8b plat: m201 vari: 512M
Find match dtb: 0
Net: Meson_Ethernet
init suspend firmware done. (ret:0)
cvbs trimming.1.v5: 0xa0, 0x0
reboot_mode=charging
Hit Enter key to stop autoboot -- :0
exit abortboot: 0
Booting...
pos 509 value is 20## ANDROID Format IMAGE
## Booting kernel from Legacy Image at 12000000 ...
Image Name: Linux-3.10.33
Image Type: ARM Linux Kernel Image (lzo compressed)
Data Size: 6154092 Bytes = 5.9 MiB
Load Address: 00208000
Entry Point:00208000
Verifying Checksum ... OK
Ramdisk start addr = 0x125df000, len = 0xdddac
Multi dtb tool version: v2 .
Multi dtb detected, support 2 dtbs.
aml_dt soc: m8b platform: m201 variant: 1G
dtb 0 soc: m8b plat: m201 vari: 1G
dtb 1 soc: m8b plat: m201 vari: 512M
Find match dtb: 0
Flat device tree start addr = 0x126bd800, len = 0x5aec magic=0xedfe0dd0
Uncompressing Kernel Image ... OK
uboot time: 2327735 us.
EFUSE machid is not set.
Using machid 0xf81 from environment
From device tree /memory/ node aml_reserved_end property, for relocate ramdisk and fdt, relocate_addr: 0x50e7001
Loading Ramdisk to 05009000, end 050e6dac ... OK
Loading Device Tree to 05000000, end 05008aeb ... OK
Starting kernel ...
https://www.znds.com/tv-506220-1-1.html试试这个教程呢 谢谢楼上的朋友。 二楼哪个网址里面的东西没有用的。 哪个人提供的所有s6的方法我都试过了，毛用 把那个教程下了吧，不要再坑其它人了 是不能刷机的吗？有没有其它办法呢？用ttl线接入有显示，但到Starting kernel ...就没动静了。 好了吗、，我的也是这样，，，无与了 我的已经搞好了，跟你一样的，有需要来找我，好了就算了qq676997355 楼上的，你是刷机刷好的吗？
页:
[1]
