C1s更换电源IC&加装TTL插针实录
本帖最后由 神蓝 于 2016-1-12 22:18 编辑C1s更换电源IC&加装TTL插针实录
图/文:神蓝
乐迷飞来一块C1s砖，没问原因，直接插电，亮一颗红灯，通常这种情况是电源部份问题，检测电源附近看到电源IC上有一个窟窿，八个脚把一个给烧毁了。
什么也不用说，直接吹下来换，注意中间有散热接触部份，烙铁是焊接不到的。（右下向上数第2脚pcb敷铜被烧毁）
焊上新电源IC，把那个脚用焊锡飞好。
既然动手了，给这位兄弟加上TTL插针。
找来一块旧声卡，把插针拆下来，正合适。
用烙铁焊接好。
蛮合衬的^_^
插上TTL，打开终端，一串欢快的代码结束了枯燥的维修过程。
?EEEE I3000000032940xf300100003877530EEEE I400000004294_M6_BL1_3003>2137333
TE : 125999
BT : 10:23:38 May 13 2014
wait pll-0x03 target is 01d4 now it is 0x000001d3
DDR clock is 468MHz with Low Power & 2T mode
DDR training :
DX0DLLCR:40000000
DX0DQTR:ffffffff
DX0DQSTR:3db05001
DX1DLLCR:40000000
DX1DQTR:ffffffff
DX1DQSTR:3db05001
DX2DLLCR:40000000
DX2DQTR:ffffffff
DX2DQSTR:3db05001
DX3DLLCR:40000000
DX3DQTR:ffffffff
DX3DQSTR:3db05001
Stage 00 Result 00000000
aml log : Total run Times
HHH
Boot From SPI
ucl decompress...true
0x12345678
Boot from internal device 1st SPI RESERVED
TE : 372848
System Started
U-boot-00000-g4a62c80(m6_letv_g28ref@4a62c808) (May 13 2014 - 10:23:24)
aml_rtc_init
aml rtc init first time!
Clear HDMI KSV RAM
DRAM:1 GiB
relocation Offset is: 105e4000
usid is: C1S5000
1 c1s board_init buf is: C1S5000
7 c1 board_init board_type is: 3
8 c1 board_init board_type is: 3
NAND:Amlogic nand flash uboot driver, Version U1.06.017 (c) 2010 Amlogic Inc.
No NAND device found!!!
NAND device id: 98 d7 84 93 72 57
NAND device: Manufacturer ID: 0x98, Chip ID: 0x98 (Toshiba A serials NAND 4GiB TC58TEG5DCJTA00 )
1 NAND chips detected
#####aml_nand_init, with RB pins and chip->chip_delay:20
bus_cycle=5, bus_timing=7, start_cycle=6, end_cycle=9,system=5.0ns
oob size is not enough for selected bch mode: NAND_BCH60_1K_MODE force bch to mode: NAND_BCH40_1K_MODE
aml_chip->oob_fill_cnt =128,aml_chip->oob_size =1280,bch_bytes =70
multi plane error for selected plane mode: NAND_TWO_PLANE_MODE force plane to : NAND_SINGLE_PLANE_MODE
aml_nand_init:oobmul =1,chip->ecc.layout->oobfree.length=32,aml_chip->oob_size=1280
aml nand env valid addr: 8000
key start_blk=1016,end_blk=1023,aml_nand_key_init:684
aml nand key valid addr: fe000000
aml nand key valid addr: fe400000
aml nand key valid addr: fe800000
aml nand key valid addr: fec00000
CONFIG_KEYSIZE=0x10000; KEYSIZE=0xfffc; bbt=0x1330; default_keyironment_size=0xeccc
i=0,register --- nand_key
NAND bbt detect factory Bad block at 7b000000
2 too much bad block!!
Creating 12 MTD partitions on "nandnormal":
0x000000800000-0x000001000000 : "bootargs"
0x000001000000-0x000001800000 : "misc"
0x000001800000-0x000002000000 : "baseparam"
0x000002000000-0x000002800000 : "logo"
0x000002800000-0x000003800000 : "aml_logo"
0x000003800000-0x000009800000 : "fastplay"
0x000009800000-0x00000a800000 : "recovery"
0x00000a800000-0x00000b800000 : "boot"
0x00000b800000-0x00002b800000 : "system"
0x00002b800000-0x00004b800000 : "cache"
0x00004b800000-0x00008bc00000 : "userdata"
NAND bbt detect factory Bad block at 7b000000
NAND bbt detect factory Bad block at 8b800000
0x00008bc00000-0x0000fe000000 : "NFTL_Part"
NAND bbt detect factory Bad block at a0000000
NAND bbt detect factory Bad block at a0800000
NAND bbt detect factory Bad block at a1800000
NAND bbt detect factory Bad block at d2000000
NAND bbt detect factory Bad block at ef400000
nandnormal initialized ok
detect mx chiprevD :0 and nand_type: 20
No NAND device found!!!
NAND device id: 98 d7 84 93 72 57
NAND device: Manufacturer ID: 0x98, Chip ID: 0x98 (Toshiba A serials NAND 4GiB TC58TEG5DCJTA00 )
1 NAND chips detected
#####aml_nand_init, with RB pins and chip->chip_delay:20
bus_cycle=5, bus_timing=7, start_cycle=6, end_cycle=9,system=5.0ns
oob size is not enough for selected bch mode: NAND_BCH60_1K_MODE force bch to mode: NAND_BCH40_1K_MODE
aml_chip->oob_fill_cnt =128,aml_chip->oob_size =1280,bch_bytes =70
multi plane error for selected plane mode: NAND_TWO_PLANE_MODE force plane to : NAND_SINGLE_PLANE_MODE
aml_nand_init:oobmul =1,chip->ecc.layout->oobfree.length=32,aml_chip->oob_size=1280
aml nand env valid addr: 8000
key start_blk=1016,end_blk=1023,aml_nand_key_init:684
aml nand key valid addr: fe000000
aml nand key valid addr: fe400000
aml nand key valid addr: fe800000
aml nand key valid addr: fec00000
CONFIG_KEYSIZE=0x10000; KEYSIZE=0xfffc; bbt=0x1330; default_keyironment_size=0xeccc
name=nand_key nand_key
NAND bbt detect factory Bad block at 7b000000
2 too much bad block!!
Creating 12 MTD partitions on "nandnormal":
0x000000800000-0x000001000000 : "bootargs"
0x000001000000-0x000001800000 : "misc"
0x000001800000-0x000002000000 : "baseparam"
0x000002000000-0x000002800000 : "logo"
0x000002800000-0x000003800000 : "aml_logo"
0x000003800000-0x000009800000 : "fastplay"
0x000009800000-0x00000a800000 : "recovery"
0x00000a800000-0x00000b800000 : "boot"
0x00000b800000-0x00002b800000 : "system"
0x00002b800000-0x00004b800000 : "cache"
0x00004b800000-0x00008bc00000 : "userdata"
NAND bbt detect factory Bad block at 7b000000
NAND bbt detect factory Bad block at 8b800000
0x00008bc00000-0x0000fe000000 : "NFTL_Part"
NAND bbt detect factory Bad block at a0000000
NAND bbt detect factory Bad block at a0800000
NAND bbt detect factory Bad block at a1800000
NAND bbt detect factory Bad block at d2000000
NAND bbt detect factory Bad block at ef400000
nandnormal initialized ok
detect mx chiprevD :0 and nand_type: 20
nand_curr_device =0
MMC: SDIO Port B: 0, SDIO Port C: 1
SPI BOOT,spi_env_relocate_spec : env_relocate_spec 53
SF: Detected MX25L3205D with page size 256, total 4 MiB
SPI NOR Flash have write protect!!!
In: serial
Out: serial
Err: serial
register usb cfg = 9fe7ef8c
Net: Meson_Ethernet
init suspend firmware done. (ret:0)
key_init(P_AO_RTI_PIN_MUX_REG (0xc8100014))_val = 0x9f5dbec4
pre_detect_storage
reboot_mode=charging
ir init
key_init(P_AO_RTI_PIN_MUX_REG (0xc8100014))_val = 0x9f5dbc54
usid is: C1S5000
1 c1s switch_boot_mode env is: C1S5000
switch_boot_mode env = C1s
P_AO_RTI_STATUS_REG2: 0x0
suspend = <NULL>
NAND read: misc offset 0x0, size 0x2046
8262 bytes read: OK
enter_recovery
### main_loop: bootcmd="run compatible_boot"
Hit any key to stop autoboot:0
compatible nand
Booting from nand ...
NAND read: logo whole chip
8388608 bytes read: OK
NAND read: boot offset 0x0, size 0x600000
6291456 bytes read: OK
pre-clear hdmi ram
hdcp get form storage medium: nand
name=nand_key nand_key
read:addr:0xfe000000,phy_blk_addr:1016,phy_page_addr:0,aml_nand_get_key:125
device:nand, init key ok!!
don't found keyname,uboot_key_read:1502
prefetch hdcp keys from nand failed
## Booting kernel from Legacy Image at 82000000 ...
Image Name: Linux-3.0.50-g15b99ad-dirty
Image Type: ARM Linux Kernel Image (lzma compressed)
Data Size: 3354207 Bytes = 3.2 MiB
Load Address: 80008000
Entry Point:80008000
Verifying Checksum ... OK
Ramdisk start addr = 0x82333800, len = 0x10b301
Uncompressing Kernel Image ... OK
machid from environment: 0x4e27
EFUSE machid is not set.
Using machid 0x4e27 from environment
Starting kernel ...
[ 0.000000@0] Initializing cgroup subsys cpu
[ 0.000000@0] Linux version 3.0.50-g15b99ad-dirty (letv@letv.localhost) (gcc version 4.6.x-google 20120106 (prerelease) (GCC) ) #2 SMP PREEMPT Tue May 13 10:26:38 CST 2014
[ 0.000000@0] CPU: ARMv7 Processor revision 0 (ARMv7), cr=10c53c7d
[ 0.000000@0] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000@0] Machine: Amlogic Meson6 g02 customer platform
[ 0.000000@0] Ignoring unrecognised tag 0x00000000
[ 0.000000@0] early_mem:528: start=0x80000000, size=0x4000000
[ 0.000000@0] early_mem:546: start=0x91000000, size=0xef00000
[ 0.000000@0] early_mem:554: start=0xa0000000, size=0x20000000
[ 0.000000@0] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000@0] PERCPU: Embedded 7 pages/cpu @c131f000 s5600 r8192 d14880 u32768
[ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on.Total pages: 206592
[ 0.000000@0] Kernel command line: root=/dev/cardblksd2 rw rootfstype=ext3 rootwait init=/init console=ttyS0,115200n8 mac=c8:0e:77:02:5b:db logo=osd1,0x84100000,720p,full androidboot.resolution=720p hdmimode=720p cvbsmode=480cvbs hlt vmalloc=256m mem=1024m a9_clk_max=1512000000 vdachwswitch=component hdmitx=
[ 0.000000@0] ******** uboot setup mac-addr: c8:e:77:2:5b:db
[ 0.000000@0] osd1:1
[ 0.000000@0] 720p:6
[ 0.000000@0] full:2
[ 0.000000@0] kernel get hdmimode form uboot is 720p
[ 0.000000@0] kernel get cvbsmode form uboot is 480cvbs
[ 0.000000@0] HDMI DEBUG: hdmitx_boot_para_setup
[ 0.000000@0] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000@0] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000@0] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000@0] Memory: 64MB 239MB 512MB = 815MB total
[ 0.000000@0] Memory: 815100k/815100k available, 19460k reserved, 524288K highmem
[ 0.000000@0] Virtual kernel memory layout:
[ 0.000000@0] vector: 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000@0] fixmap: 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000@0] DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
[ 0.000000@0] vmalloc : 0xe0000000 - 0xf0000000 ( 256 MB)
[ 0.000000@0] lowmem: 0xc0000000 - 0xdff00000 ( 511 MB)
[ 0.000000@0] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000@0] modules : 0xbf000000 - 0xbfe00000 (14 MB)
[ 0.000000@0] .init : 0xc0008000 - 0xc0037000 ( 188 kB)
[ 0.000000@0] .text : 0xc0037000 - 0xc0824d2c (8120 kB)
[ 0.000000@0] .data : 0xc0826000 - 0xc087f2e0 ( 357 kB)
[ 0.000000@0] .bss : 0xc087f304 - 0xc0b15be8 (2651 kB)
[ 0.000000@0] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000@0] Preemptible hierarchical RCU implementation.
[ 0.000000@0] RCU debugfs-based tracing is enabled.
[ 0.000000@0] NR_IRQS:256
[ 0.000000@0] gic_init: irq_offset=0
[ 0.000000@0] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 4294967ms
[ 0.000000@0] MESON TIMER-A c0839ec0
[ 0.000000@0] Disable timerA
[ 0.000000@0] Console: colour dummy device 80x30
[ 0.000000@0] console enabled
[ 0.281039@0] Calibrating delay loop... 2387.14 BogoMIPS (lpj=11935744)
[ 0.340046@0] pid_max: default: 32768 minimum: 301
[ 0.342262@0] Mount-cache hash table entries: 512
[ 0.347529@0] Initializing cgroup subsys cpuacct
[ 0.351411@0] Initializing cgroup subsys freezer
[ 0.355988@0] CPU: Testing write buffer coherency: ok
[ 0.361178@0] MESON TIMER-B c0839f80
[ 0.364526@0] Disable timerA
[ 0.367383@0] Disable timerB
[ 0.370252@0] Disable timerA
[ 0.373241@0] L310 cache controller enabled
[ 0.377278@0] l2x0: 8 ways, CACHE_ID 0x4100a0c8, AUX_CTRL 0x7e462c01, Cache size: 524288 B
[ 0.385576@0]prefetch=0x31000006
[ 0.388907@0] ===actlr=0x41
[ 0.391691@0] ===actlr=0x4b
[ 0.394462@0] SCU_CTRL: scu_ctrl=0x69
[ 0.398108@0] pl310: aux=0x7e462c01, prefetch=0x31000006
[ 0.501493@1] CPU1: Booted secondary processor
[ 0.561204@1] MESON TIMER-D c083a100
[ 0.561231@0] Brought up 2 CPUs
[ 0.561239@0] SMP: Total of 2 processors activated (4780.85 BogoMIPS).
[ 0.573196@1] Disable timerD
[ 0.576220@0] devtmpfs: initialized
[ 0.583452@0] clkrate [ xtal ] : 24000000
[ 0.583524@0] clkrate [ pll_sys ] : 1200000000
[ 0.587949@0] clkrate [ pll_fixed ] : 2000000000
[ 0.592568@0] clkrate [ pll_vid2 ] : 378000000
[ 0.596977@0] clkrate [ pll_hpll ] : 378000000
[ 0.601494@0] clkrate [ pll_ddr ] : 468000000
[ 0.605743@0] clkrate [ a9_clk ] : 1200000000
[ 0.610147@0] clkrate [ clk81 ] : 200000000
[ 0.614353@0] clkrate [ usb0 ] : 0
[ 0.617731@0] clkrate [ usb1 ] : 0
[ 0.622093@0] print_constraints: dummy:
[ 0.625076@0] NET: Registered protocol family 16
[ 0.630589@1] in
[ 0.632749@1] in
[ 0.636525@1] ***vcck: vcck_pwm_initregister lm device 0
[ 0.641710@1] register lm device 1
[ 0.647203@1] usb_wifi_power: on.
[ 0.648397@1] chip version=edffb75c
[ 0.651879@1] vdac_switch_init_module
[ 0.655511@1] tv_init_module
[ 0.658261@1] major number 254 for disp
[ 0.662169@1] vout_register_server
[ 0.665547@1] register tv module server ok
[ 0.669894@1] /opt/yuetv_release_c2/src/yuetv_2/common/drivers/amlogic/i2c/aml_i2c.c : aml_i2c_init
[ 0.678944@1] HDMI DEBUG: amhdmitx_init
[ 0.683262@1] HDMI Ver: 2013Aug25a
[ 0.686658@1] HDMI DEBUG: amhdmitx_probe
[ 0.691501@1] Set HDMI:Chip C
[ 0.694111@1] HDMI: get hdmi platform data
[ 0.698183@1] HDMI 5V Power On
[ 0.701235@1] HDMI DEBUG: HDMITX_M1B_Init
[ 0.705824@1] HDMI DEBUG: HDMITX_M1B_Init
[ 0.710423@1] HDMI DEBUG: hdmi_hw_init
[ 0.714834@1] HDMI: get brd phy data
[ 0.718396@1] hdmi phy setting
[ 0.721692@1] HDMI: get brd phy data
[ 0.724968@1] hdmi phy setting
[ 0.729180@1] ------------[ cut here ]------------
[ 0.732759@1] WARNING: at /opt/yuetv_release_c2/src/yuetv_2/common/fs/sysfs/dir.c:455 sysfs_add_one+0x88/0xbc()
[ 0.742931@1] HDMI: reset intr mask
[ 0.746275@1] sysfs: cannot create duplicate filename '/module/hdmitx/version'
[ 0.753482@1] Modules linked in:
[ 0.756718@1] [<c0043b44>] (unwind_backtrace+0x0/0xf8) from [<c0061ee4>] (warn_slowpath_common+0x4c/0x64)
[ 0.766248@1] HDMI DEBUG: hdmi_task_handle
[ 0.766254@0] HDMI irq 1
[ 0.766264@0] Reg0x196 = 0x2Reg0x80 = 0x1Reg0x26 = 0xc
[ 0.766282@0] Reg0x196 = 0x42Reg0x80 = 0x1Reg0x26 = 0x4c
[ 0.784569@1] [<c0061ee4>] (warn_slowpath_common+0x4c/0x64) from [<c0061f90>] (warn_slowpath_fmt+0x30/0x40)
[ 0.794286@1] [<c0061f90>] (warn_slowpath_fmt+0x30/0x40) from [<c0122df4>] (sysfs_add_one+0x88/0xbc)
[ 0.803405@1] [<c0122df4>] (sysfs_add_one+0x88/0xbc) from [<c0121f38>] (sysfs_add_file_mode+0x4c/0x9c)
[ 0.812693@1] [<c0121f38>] (sysfs_add_file_mode+0x4c/0x9c) from [<c000fa64>] (param_sysfs_init+0x70/0x1b0)
[ 0.822331@1] [<c000fa64>] (param_sysfs_init+0x70/0x1b0) from [<c003770c>] (do_one_initcall+0xfc/0x164)
[ 0.831694@1] [<c003770c>] (do_one_initcall+0xfc/0x164) from [<c0008988>] (kernel_init+0x98/0x13c)
[ 0.840628@1] [<c0008988>] (kernel_init+0x98/0x13c) from [<c003e0c0>] (kernel_thread_exit+0x0/0x8)
[ 0.849584@1] ---[ end trace 1b75b31a2719ed1c ]---
[ 0.893708@1] bio: create slab <bio-0> at 0
[ 0.894572@1] SCSI subsystem initialized
[ 0.896405@1] usbcore: registered new interface driver usbfs
[ 0.902440@1] usbcore: registered new interface driver hub
[ 0.907409@1] usbcore: registered new device driver usb
[ 0.912900@1] LCD driver init
[ 0.915592@1] = 0xff
[ 0.918376@1] = 0x0
[ 0.921252@1] = 0x814d3928
[ 0.924713@1] = 0x6b425012
[ 0.928185@1] = 0x110
[ 0.931229@1] = 0x1043e
[ 0.934434@1] = 0x10843
[ 0.937646@1] = 0x100
[ 0.940684@1] = 0x80000
[ 0.943902@1] = 0x88001
[ 0.947107@1] = 0x80003
[ 0.950319@1] = 0x101
[ 0.953362@1] = 0x8c0000c3
[ 0.956829@1] = 0x52
[ 0.959780@1] = 0x2029
[ 0.962909@1] = 0x4040
[ 0.966030@1] = 0x19
[ 0.968981@1] = 0x288
[ 0.972024@1] = 0xc87
[ 0.975057@1] = 0xce3
[ 0.978095@1] = 0x50
[ 0.981046@1] = 0xf0
[ 0.984001@1] = 0x50
[ 0.986949@1] = 0x2b0
[ 0.989987@1] = 0xcb0
[ 0.993028@1] = 0x4
[ 0.995889@1] = 0x8
[ 0.998753@1] = 0x4
[ 1.001621@1] = 0x8
[ 1.004482@1] = 0x288
[ 1.007520@1] = 0xc87
[ 1.010558@1] = 0x1d
[ 1.013513@1] = 0x2ec
[ 1.016547@1] = 0x100
[ 1.019585@1] = 0xa8
[ 1.022548@1] = 0xa8
[ 1.025488@1] = 0x100
[ 1.028525@1] = 0x0
[ 1.031394@1] = 0x5
[ 1.034254@1] = 0x2ed
[ 1.037292@1] = 0x100
[ 1.040330@1] = 0x0
[ 1.043198@1] = 0x200
[ 1.046233@1] = 0x0
[ 1.049097@1] = 0x0
[ 1.051965@1] = 0x9061
[ 1.055087@1] = 0xa061
[ 1.058211@1] = 0xb061
[ 1.061340@1] = 0x1
[ 1.064201@1] = 0x1
[ 1.067065@1] = 0x1
[ 1.069929@1] = 0x1
[ 1.072798@1] = 0x1
[ 1.075658@1] = 0x1
[ 1.078523@1] = 0xa
[ 1.081391@1] = 0x1000
[ 1.084512@1] = 0x3102
[ 1.087637@1] = 0x54
[ 1.090588@1] = 0x1
[ 1.093456@1] = 0x0
[ 1.096318@1] tvoutc_setmode
[ 1.099616@1] mode is: 6
[ 1.102139@1] VPU_VIU_VENC_MUX_CTRL: 0xa
[ 1.106038@1] viu chan = 1
[ 1.108729@1] VPU_VIU_VENC_MUX_CTRL: 0xa
[ 1.191513@1] request_fiq:152: fiq=35
[ 1.191541@1] request_fiq:186: end
[ 1.225052@0] print_constraints: vcck: 1010 <--> 1370 mV at 1380 mV
[ 1.226229@0] Advanced Linux Sound Architecture Driver Version 1.0.24.
[ 1.232962@0] Bluetooth: Core ver 2.16
[ 1.236106@0] NET: Registered protocol family 31
[ 1.240606@0] Bluetooth: HCI device and connection manager initialized
[ 1.247149@0] Bluetooth: HCI socket layer initialized
[ 1.252189@0] Bluetooth: L2CAP socket layer initialized
[ 1.257376@0] Bluetooth: SCO socket layer initialized
[ 1.263447@1] Switching to clocksource Timer-E
[ 1.271222@0] Switched to NOHz mode on CPU #0
[ 1.271230@1] Switched to NOHz mode on CPU #1
[ 1.276883@0] cfg80211: Calling CRDA to update world regulatory domain
[ 1.287372@1] NET: Registered protocol family 2
[ 1.287514@1] IP route cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 1.294040@1] TCP established hash table entries: 65536 (order: 7, 524288 bytes)
[ 1.301813@1] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
[ 1.308627@1] TCP: Hash tables configured (established 65536 bind 65536)
[ 1.314562@1] TCP reno registered
[ 1.318211@1] HDMI: EDID Ready
[ 1.321006@1] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 1.326961@1] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 1.333339@1] CEC: Physical address: 0x1000
[ 1.337491@1] CEC: Physical address: 1.0.0.0
[ 1.341771@1] HDMI: get current mode: 720p
[ 1.345826@1] set mode VIC 4 (cd0,cs0,pm1,vd0,1)
[ 1.347173@0] NET: Registered protocol family 1
[ 1.347354@0] Unpacking initramfs...
[ 1.358612@1] HDMI DEBUG: hdmi_hw_reset
[ 1.363001@1] HDMI: get brd phy data
[ 1.366551@1] hdmi phy setting
[ 1.370701@1] HDMI: get brd phy data
[ 1.373149@1] hdmi phy setting
[ 1.376240@1] HDMI DEBUG: hdmitx_set_pll
[ 1.380730@1] param->VIC:4
[ 1.383393@1] mode is: 6
[ 1.385912@1] VPU_VIU_VENC_MUX_CTRL: 0xa
[ 1.389837@1] viu chan = 1
[ 1.392505@1] VPU_VIU_VENC_MUX_CTRL: 0xa
[ 1.402734@0] Freeing initrd memory: 1068K
[ 1.403988@0] highmem bounce pool size: 64 pages
[ 1.406035@0] ashmem: initialized
[ 1.419980@1] Sink is HDMI device
[ 1.420022@1] Source in HDMI Mode
[ 1.421156@1] CEC not ready
[ 1.424027@0] NTFS driver 2.1.30 .
[ 1.428566@0] fuse init (API version 7.16)
[ 1.432866@0] msgmni has been set to 570
[ 1.437033@0] io scheduler noop registered
[ 1.440221@0] io scheduler deadline registered (default)
[ 1.526931@1] HDMI: audio channel num is 0
[ 1.526989@1] current VIC: 4
[ 1.528251@1] audio sample rate: 0
[ 1.531636@1] HDMI: reset audio N para
[ 1.535374@1] PCM out to HDMI
[ 1.561698@1] Time out: AIU_HDMI_CLK_DATA_CTRL
[ 1.561742@1] i2s_to_spdif_flag:1
[ 1.563891@1] Enable audio spdif to HDMI
[ 1.567882@1] HDMI: set audio param
[ 1.624675@0] loop: module loaded
[ 1.626919@0] PPP generic driver version 2.4.2
[ 1.627436@0] PPP Deflate Compression module registered
[ 1.631987@0] PPP BSD Compression module registered
[ 1.637250@0] PPP MPPE Compression module registered
[ 1.641797@0] NET: Registered protocol family 24
[ 1.646400@0] tun: Universal TUN/TAP device driver, 1.6
[ 1.651656@0] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 1.658811@0] usbcore: registered new interface driver cdc_acm
[ 1.663756@0] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 1.671945@0] Initializing USB Mass Storage driver...
[ 1.677095@0] usbcore: registered new interface driver usb-storage
[ 1.683111@0] USB Mass Storage support registered.
[ 1.688121@0] usbcore: registered new interface driver usbserial
[ 1.693875@0] usbserial: USB Serial Driver core
[ 1.698500@0] USB Serial support registered for GSM modem (1-port)
[ 1.704646@0] usbcore: registered new interface driver option
[ 1.710295@0] option: v0.7.2:USB Driver for GSM modems
[ 1.716167@0] mousedev: PS/2 mouse device common for all mice
[ 1.722398@0] usbcore: registered new interface driver iforce
[ 1.728046@0] usbcore: registered new interface driver xpad
[ 1.732611@0] usbcore: registered new interface driver usb_nanosic_ts
[ 1.739765@0] i2c /dev entries driver
[ 1.742800@0] lirc_dev: IR Remote Control driver registered, major 250
[ 1.749109@0] IR NEC protocol handler initialized
[ 1.753767@0] IR RC5(x) protocol handler initialized
[ 1.758724@0] IR RC6 protocol handler initialized
[ 1.763402@0] IR JVC protocol handler initialized
[ 1.768098@0] IR Sony protocol handler initialized
[ 1.772863@0] IR RC5 (streamzap) protocol handler initialized
[ 1.778601@0] IR LIRC bridge handler initialized
[ 1.783192@0] Linux video capture interface: v2.00
[ 1.788210@0] usbcore: registered new interface driver uvcvideo
[ 1.793869@0] USB Video Class driver (v1.1.0)
[ 1.799024@0] device-mapper: uevent: version 1.0.3
[ 1.803653@0] device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: dm-devel@redhat.com
[ 1.811849@0] Bluetooth: HCI UART driver ver 2.2
[ 1.816180@0] Bluetooth: HCI H4 protocol initialized
[ 1.821173@0] cpuidle: using governor ladder
[ 1.825378@0] cpuidle: using governor menu
[ 1.830598@0] usbcore: registered new interface driver usbhid
[ 1.835186@0] usbhid: USB HID core driver
[ 1.839965@0] logger: created 256K log 'log_main'
[ 1.844128@0] logger: created 256K log 'log_events'
[ 1.849002@0] logger: created 256K log 'log_radio'
[ 1.853749@0] logger: created 256K log 'log_system'
[ 1.858490@0] vout_init_module
[ 1.861438@0] start init vout module
[ 1.865229@0] createvout attribute ok
[ 1.869246@0] ge2d_init
[ 1.871561@0] ge2d_dev major:248
[ 1.875324@0] ge2d start monitor
[ 1.878210@0] osd_init
[ 1.878215@1] ge2d workqueue monitor start
[ 1.884702@0] 0x84100000-0x850fffff
[ 1.888983@0] Frame buffer memory assigned at phy:0x84100000, vir:0xe1000000, size=16384K
[ 1.896914@0] ---------------clear framebuffer0 memory
[ 1.914859@0] 0x85100000-0x851fffff
[ 1.914911@0] Frame buffer memory assigned at phy:0x85100000, vir:0xe0200000, size=1024K
[ 1.921401@0] init fbdev bpp is :24
[ 1.926063@0] osd probe ok
[ 1.934536@0] amlvideo-000: V4L2 device registered as video10
[ 1.935327@0]set pinmux c08753d8
[ 1.938073@0]set pinmux c08753e0
[ 1.966893@0] UART_ttyS0:(irq = 122)
[ 1.996888@0] UART_ttyS1:(irq = 58)
[ 1.997045@0] dwc_otg: version 2.94a 05-DEC-2012
[ 2.499228@0] USB (0) use clock source: XTAL input
[ 2.566864@1] HDMITX: no HDCP key available
[ 2.566888@1] HDMITX: HDCP Key error
[ 2.568964@1] HDMITX: no HDCP key available
[ 2.573125@1] HDMITX: HDCP Key error
[ 2.900179@0] Core Release: 2.94a
[ 2.900202@0] Setting default values for core params
[ 3.302808@0] Using Buffer DMA mode
[ 3.302831@0] OTG VER PARAM: 1, OTG VER FLAG: 1
[ 3.305163@0] Working on port type = HOST
[ 3.309241@0] dwc_otg lm0: DWC OTG Controller
[ 3.313580@0] dwc_otg lm0: new USB bus registered, assigned bus number 1
[ 3.320239@0] dwc_otg lm0: irq 62, io mem 0x00000000
[ 3.328249@0] Init: Port Power? op_state=1
[ 3.329207@0] Init: Power Port (0)
[ 3.333440@0] hub 1-0:1.0: USB hub found
[ 3.336510@0] hub 1-0:1.0: 1 port detected
[ 3.740932@0] Core Release: 2.94a
[ 3.740954@0] Setting default values for core params
[ 4.143569@0] Using Buffer DMA mode
[ 4.143592@0] OTG VER PARAM: 1, OTG VER FLAG: 1
[ 4.145927@0] Working on port type = HOST
[ 4.149993@0] dwc_otg lm1: DWC OTG Controller
[ 4.154292@0] dwc_otg lm1: new USB bus registered, assigned bus number 2
[ 4.160994@0] dwc_otg lm1: irq 63, io mem 0x00000000
[ 4.168975@0] Init: Port Power? op_state=1
[ 4.169970@0] Init: Power Port (0)
[ 4.174169@0] hub 2-0:1.0: USB hub found
[ 4.177315@0] hub 2-0:1.0: 1 port detected
[ 4.181733@0] Amlogic nand flash Kernel driver, Version K1.06.015 (c) 2010 Amlogic Inc.
[ 4.189363@0] ####Version of Uboot must be newer than U1.06.011!!!!!
[ 4.195795@0] 2
[ 4.197521@0] SPI BOOT, m3_nand_probe continue i 0
[ 4.202263@0] chip->controller=c09ed01c
[ 4.206079@0] checking ChiprevD :0
[ 4.209492@0] aml_nand_probe checked chiprev:0
[ 4.213904@0] init bus_cycle=17, bus_timing=10, start_cycle=10, end_cycle=10,system=5.0ns
[ 4.222505@0] No NAND device found.
[ 4.225763@0] NAND device id: 98 d7 84 93 72 57
[ 4.230158@0] NAND device: Manufacturer ID: 0x98, Chip ID: 0x98 (Toshiba A serials NAND 4GiB TC58TEG5DCJTA00 )
[ 4.240248@0] #####aml_nand_init, with RB pins and chip->chip_delay:20
[ 4.246620@0] bus_cycle=5, bus_timing=7, start_cycle=6, end_cycle=9,system=5.0ns
[ 4.254020@0] oob size is not enough for selected bch mode: NAND_BCH60_1K_MODE force bch to mode: NAND_BCH40_1K_MODE
[ 4.264518@0] aml_chip->oob_fill_cnt =128,aml_chip->oob_size =1280,bch_bytes =70
[ 4.271896@0] multi plane error for selected plane mode: NAND_TWO_PLANE_MODE force plane to : NAND_SINGLE_PLANE_MODE
[ 4.282421@0]oob layout use nand base oob layout oobsize = 32,oobmul =1,mtd->oobsize =1280,aml_chip->oob_size =1280
[ 4.300444@0] aml nand env valid addr: 8000
[ 4.317160@0] nand env: nand_env_probe.
[ 4.317867@0] nand key: nand_key_probe.
[ 4.319359@0] key start_blk=1016,end_blk=1023,aml_nand_key_init:651
[ 4.331532@0] aml nand key valid addr: fe000000
[ 4.331557@0] aml nand key valid addr: fe400000
[ 4.335107@0] aml nand key valid addr: fe800000
[ 4.339735@0] aml nand key valid addr: fec00000
[ 4.344359@0] i=0,register --- nand_key NAND bbt detect factory Bad block at 7b000000
[ 4.353523@0]NAND bbt detect factory Bad block at 8b800000
[ 4.357969@0] Creating 12 MTD partitions on "A serials NAND 4GiB TC58TEG5DCJTA00 ":
[ 4.365579@0] 0x000000800000-0x000001000000 : "bootargs"
[ 4.374934@0] 0x000001000000-0x000001800000 : "misc"
[ 4.376975@1] Indeed it is in host mode hprt0 = 00021501
[ 4.384033@0] 0x000001800000-0x000002000000 : "baseparam"
[ 4.387842@0] 0x000002000000-0x000002800000 : "logo"
[ 4.392644@0] 0x000002800000-0x000003800000 : "aml_logo"
[ 4.398035@0] 0x000003800000-0x000009800000 : "fastplay"
[ 4.403250@0] 0x000009800000-0x00000a800000 : "recovery"
[ 4.408672@0] 0x00000a800000-0x00000b800000 : "boot"
[ 4.413521@0] 0x00000b800000-0x00002b800000 : "system"
[ 4.418820@0] 0x00002b800000-0x00004b800000 : "cache"
[ 4.423681@0] 0x00004b800000-0x00008c000000 : "userdata"
[ 4.427869@0]NAND bbt detect factory Bad block at 7b000000
[ 4.433454@0]NAND bbt detect factory Bad block at 8b800000
[ 4.440480@0] 0x00008c000000-0x0000fe000000 : "NFTL_Part"
[ 4.444591@0]NAND bbt detect factory Bad block at a0000000
[ 4.450488@0]NAND bbt detect factory Bad block at a0800000
[ 4.456018@0]NAND bbt detect factory Bad block at a1800000
[ 4.461798@0]NAND bbt detect factory Bad block at d2000000
[ 4.467507@0]NAND bbt detect factory Bad block at ef400000
[ 4.474594@0] init_aml_nftl start
[ 4.476512@0] mtd->name: system
[ 4.479721@0] nftl version 131218a
[ 4.483023@0] nftl part attr 0
[ 4.486068@0] nftl start:128,16
[ 4.489532@0] first
[ 4.528891@0] second 128,112
[ 4.556926@1] usb 2-1: new high speed USB device number 2 using dwc_otg
[ 4.558193@1] Indeed it is in host mode hprt0 = 00001101
[ 4.614591@0] current used block :85
[ 4.627028@0] free block cnt = 46
[ 4.627047@0] nftl ok!
[ 4.627565@0] aml_nftl_blk->mbd.tr.name =system
[ 4.632349@1] aml_nftl_init_bounce_buf, use cache here
[ 4.637449@0]system: unknown partition table
[ 4.641421@0] _nftl_init_bounce_buf already init 1000
[ 4.646135@0] aml_nftl_add_mtd ok
[ 4.649486@0] mtd->name: cache
[ 4.652477@0] nftl version 131218a
[ 4.655869@0] nftl part attr 0
[ 4.658951@0] nftl start:128,16
[ 4.662339@0] first
[ 4.703008@0] second 95,112
[ 4.759796@1] hub 2-1:1.0: USB hub found
[ 4.760147@1] hub 2-1:1.0: 4 ports detected
[ 4.766960@0] current used block :33
[ 4.864810@0] free block cnt = 64
[ 4.864829@0] nftl ok!
[ 4.865334@0] aml_nftl_blk->mbd.tr.name =cache
[ 4.870239@1] aml_nftl_init_bounce_buf, use cache here
[ 4.875116@0]cache: unknown partition table
[ 4.879113@0] _nftl_init_bounce_buf already init 1000
[ 4.883760@0] aml_nftl_add_mtd ok
[ 4.887102@0] mtd->name: userdata
[ 4.890351@0] nftl version 131218a
[ 4.893757@0] nftl part attr 0
[ 4.896793@0]NAND bbt detect factory Bad block at 7b000000
[ 4.902537@0]NAND bbt detect factory Bad block at 8b800000
[ 4.908255@0] size_in_blk 258; total_block 256;
[ 4.912824@0] nftl start:256,32
[ 4.916498@0] first
[ 4.981567@0]NAND bbt detect factory Bad block at 7b000000
[ 5.001254@0]NAND bbt detect factory Bad block at 8b800000
[ 5.001653@0] second 55,224
[ 5.040944@0] current used block :202
[ 5.093566@0] free block cnt = 203
[ 5.093585@0] nftl ok!
[ 5.094546@0] aml_nftl_blk->mbd.tr.name =data
[ 5.098811@1] aml_nftl_init_bounce_buf, use cache here
[ 5.103878@0]data: unknown partition table
[ 5.107788@0] _nftl_init_bounce_buf already init 1000
[ 5.112421@0] aml_nftl_add_mtd ok
[ 5.115720@0] mtd->name: NFTL_Part
[ 5.119151@0] nftl version 131218a
[ 5.122530@0] nftl part attr 0
[ 5.125543@0]NAND bbt detect factory Bad block at a0000000
[ 5.131289@0]NAND bbt detect factory Bad block at a0800000
[ 5.137027@0]NAND bbt detect factory Bad block at a1800000
[ 5.142750@0]NAND bbt detect factory Bad block at d2000000
[ 5.148482@0]NAND bbt detect factory Bad block at ef400000
[ 5.154180@0] size_in_blk 456; total_block 451;
[ 5.158797@0] nftl start:451,56
[ 5.163041@0] first
[ 5.190717@0]NAND bbt detect factory Bad block at a0000000
[ 5.191163@0]NAND bbt detect factory Bad block at a0800000
[ 5.197557@0]NAND bbt detect factory Bad block at a1800000
[ 5.266636@0]NAND bbt detect factory Bad block at d2000000
[ 5.305437@0]NAND bbt detect factory Bad block at ef400000
[ 5.324903@0] second 0,395
[ 5.324924@0] all block full!!
[ 5.325006@0] free block cnt = 451
[ 5.328417@0] nftl ok!
[ 5.331702@0] aml_nftl_blk->mbd.tr.name =media
[ 5.335911@1] aml_nftl_init_bounce_buf, use cache here
[ 5.340389@0]media: unknown partition table
[ 5.344923@0] _nftl_init_bounce_buf already init 1000
[ 5.349696@0] aml_nftl_add_mtd ok
[ 5.352956@0] init_aml_nftl end
[ 5.356081@0] ethernetinit(dbg=1)
[ 5.360302@0] ethernet base addr is f3610000
[ 5.364498@0] set_phy_mode() phy_Identifier: 0x0
[ 5.369263@0] ethernet: MII PHY 0007c0f1h found at address 1, status 0x7809 advertising 01e1.
[ 5.377712@0] find phy phy_Identifier=7c0f1
[ 5.381770@0] write mac add to:df9a6748: c8 0e 77 02 5b db |..w.[.|
[ 5.388460@0] eth0: mixed no checksumming and other settings.
[ 5.394215@0] Amlogic A/V streaming port init
[ 5.401988@0] regist mpeg12 codec profile
[ 5.402177@0] regist mpeg4 codec profile
[ 5.405989@0] amvdec_vc1 module init
[ 5.409720@0] regist vc1 codec profile
[ 5.413280@0] amvdec_h264 module init
[ 5.417082@0] regist h264 codec profile
[ 5.420744@0] amvdec_h264mvc module init
[ 5.424847@0] regist mjpeg codec profile
[ 5.428590@0] amvdec_real module init
[ 5.432306@0] regist real codec profile
[ 5.437177@0] Vsync pts inc(before): 1500
[ 5.440016@0] Vsync pts inc(after): 1500
[ 5.443921@0] request_fiq:152: fiq=35
[ 5.447607@0] request_fiq:186: end
[ 5.451640@0] Remote Driver
[ 5.454142@0] input: aml_keypad as /devices/platform/meson-remote/input/input0
[ 5.461706@0] meson_remote_pinmux_setup()
[ 5.464928@0] Remote platform_data g_remote_base=f3100480
[ 5.470356@0] Remote date_valye======0,status == 8915d20
[ 5.475632@0] remote config major:244
[ 5.479861@0] physical address:0x9f950000
[ 5.483429@0] Meson KeyInput init
[ 5.486685@0] Key 117 registed.
[ 5.489800@0] Key 116 registed.
[ 5.493091@0] input: key_input as /devices/platform/meson-keyinput.0/input/input1
[ 5.500779@0] Meson KeyInput register RTC interrupt
[ 5.505054@0] Meson KeyInput major=243
[ 5.509993@0]spi_nor_probe 586
[ 5.512147@0] SPI BOOT: spi_nor_probe 591
[ 5.516419@0] spi_nor apollospi:0: mx25l3205d (4096 Kbytes)
[ 5.522003@0] Creating 2 MTD partitions on "apollospi:0":
[ 5.527369@0] 0x000000000000-0x000000400000 : "bootloader"
[ 5.534241@0] 0x000000080000-0x000000088000 : "ubootenv"
[ 5.540010@0] Memory Card media Major: 253
[ 5.542325@0] card max_req_size is 128K
[ 5.546793@0] card creat process sucessful
[ 5.550265@0]
[ 5.550269@0] SD/MMC initialization started......
[ 6.186866@0] mmc data3 pull high
[ 6.187090@0] sd_mmc_info->card_type=0
[ 6.188274@0] begin SDIO check ......
[ 6.214491@0] sdio_timeout_int_times = 0; timeout = 498
[ 6.237087@0] sdio_timeout_int_times = 0; timeout = 497
[ 6.237114@0] SEND OP timeout @1
[ 6.239877@0] mmc data3 pull high
[ 6.243366@0] begin SD&SDHC check ......
[ 6.289431@0] sdio_timeout_int_times = 0; timeout = 498
[ 6.289458@0] SEND IF timeout @2
[ 6.314984@0] sdio_timeout_int_times = 0; timeout = 498
[ 6.315011@0] begin MMC check ......
[ 6.359427@0] sdio_timeout_int_times = 0; timeout = 498
[ 6.359456@0] No any SD/MMC card detected!
[ 6.363092@0] #SD_MMC_ERROR_DRIVER_FAILURE error occured in sd_voltage_validation()
[ 6.370761@0] unit_state 3
[ 6.375141@0] DSP start addr 0xc4000000
[ 6.379304@0] register dsp to char divece(232)
[ 6.389259@0] DSP pcmenc stream buffer to
[ 6.390175@0] amlogic audio dsp pcmenc device init!
[ 6.395923@0] amlogic audio spdif interface device init!
[ 6.401619@0] using rtc device, aml_rtc, for alarms
[ 6.405047@0] aml_rtc aml_rtc: rtc core: registered aml_rtc as rtc0
[ 6.412367@0] efuse===========================================
[ 6.417942@0] efuse: device efuse created
[ 6.421359@0] efuse--------------------------------------------
[ 6.427255@0] keys===========================================
[ 6.432882@0] keys_devno=ee00000
[ 6.436612@0] efuse: device aml_keys created
[ 6.440398@0] amlkeys=0
[ 6.442878@0] platform_driver_register--aml_keys_driver--------------------
[ 6.466876@0] 6amlogic audio data interface device init!
[ 6.467560@0] amlogic rfkill init
[ 6.497046@0] BT_RADIO going: on
[ 6.497067@0] BCM_BT: going ON
[ 6.557063@0] aml_hw_crypto initialization.
[ 6.558023@0] usbcore: registered new interface driver snd-usb-audio
[ 6.562876@0] enter dummy_codec_audio_probe
[ 6.566304@0] sound card index = #0
[ 6.569468@0] sound card index = #(null)
[ 6.573661@0] aml-pcm 0:playback preallocate_dma_buffer: area=ffdf0000, addr=9f0f8000, size=16384
[ 6.582768@0] iec958 0: preallocate dma buffer start=ffde0000, size=10000
[ 6.589783@0] aml-pcm 1:capture preallocate_dma_buffer: area=ffda0000, addr=9f340000, size=65536
[ 6.597917@0] asoc: dummy_codec <-> aml-dai0 mapping ok
[ 6.604552@0] ALSA device list:
[ 6.606211@0] #0: AML-DUMMY-CODEC
[ 6.609897@0] GACT probability NOT on
[ 6.613336@0] Mirror/redirect action on
[ 6.617192@0] u32 classifier
[ 6.620011@0] Actions configured
[ 6.623572@0] Netfilter messages via NETLINK v0.30.
[ 6.628509@0] nf_conntrack version 0.5.0 (12752 buckets, 51008 max)
[ 6.635431@0] ctnetlink v0.93: registering with nfnetlink.
[ 6.640238@0] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[ 6.647300@0] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[ 6.653985@0] xt_time: kernel timezone is -0000
[ 6.657994@0] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 6.663382@0] arp_tables: (C) 2002 David S. Miller
[ 6.668117@0] TCP cubic registered
[ 6.672554@0] NET: Registered protocol family 10
[ 6.676817@0] Mobile IPv6
[ 6.678717@0] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 6.684281@0] IPv6 over IPv4 tunneling driver
[ 6.689828@0] NET: Registered protocol family 17
[ 6.693136@0] NET: Registered protocol family 15
[ 6.697897@0] Bridge firewalling registered
[ 6.701983@0] Bluetooth: RFCOMM TTY layer initialized
[ 6.706958@0] Bluetooth: RFCOMM socket layer initialized
[ 6.712195@0] Bluetooth: RFCOMM ver 1.11
[ 6.716101@0] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 6.721601@0] Bluetooth: BNEP filters: protocol multicast
[ 6.726989@0] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 6.733231@0] NET: Registered protocol family 35
[ 6.737990@0] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 6.745447@0] DDR low power is enable.
[ 6.749248@0] enter meson_pm_probe!
[ 6.752647@0] meson_pm_probe done !
[ 6.756601@0] ------------[ cut here ]------------
[ 6.760907@0] WARNING: at /opt/yuetv_release_c2/src/yuetv_2/common/kernel/smp.c:459 smp_call_function_many+0xc8/0x280()
[ 6.771647@0] Modules linked in:
[ 6.774884@0] [<c0043b44>] (unwind_backtrace+0x0/0xf8) from [<c0061ee4>] (warn_slowpath_common+0x4c/0x64)
[ 6.784415@0] [<c0061ee4>] (warn_slowpath_common+0x4c/0x64) from [<c0061f18>] (warn_slowpath_null+0x1c/0x24)
[ 6.794222@0] [<c0061f18>] (warn_slowpath_null+0x1c/0x24) from [<c008f598>] (smp_call_function_many+0xc8/0x280)
[ 6.804292@0] [<c008f598>] (smp_call_function_many+0xc8/0x280) from [<c008f784>] (smp_call_function+0x34/0x68)
[ 6.814276@0] [<c008f784>] (smp_call_function+0x34/0x68) from [<c0049c2c>] (clk_set_rate_a9+0x9c/0xdc)
[ 6.823560@0] [<c0049c2c>] (clk_set_rate_a9+0x9c/0xdc) from [<c0049f28>] (meson_clk_set_rate+0x130/0x168)
[ 6.833108@0] [<c0049f28>] (meson_clk_set_rate+0x130/0x168) from [<c0049ff4>] (clk_set_rate+0x94/0xbc)
[ 6.842397@0] [<c0049ff4>] (clk_set_rate+0x94/0xbc) from [<c0052d28>] (meson_cpufreq_target_locked.isra.2+0x14c/0x224)
[ 6.853072@0] [<c0052d28>] (meson_cpufreq_target_locked.isra.2+0x14c/0x224) from [<c0052e24>] (meson_cpufreq_target+0x24/0x3c)
[ 6.864445@0] [<c0052e24>] (meson_cpufreq_target+0x24/0x3c) from [<c0370570>] (__cpufreq_driver_target+0x50/0x64)
[ 6.874688@0] [<c0370570>] (__cpufreq_driver_target+0x50/0x64) from [<c0372d1c>] (cpufreq_governor_performance+0x28/0x30)
[ 6.885622@0] [<c0372d1c>] (cpufreq_governor_performance+0x28/0x30) from [<c0370658>] (__cpufreq_governor+0xb0/0x138)
[ 6.896211@0] [<c0370658>] (__cpufreq_governor+0xb0/0x138) from [<c03714b8>] (__cpufreq_set_policy+0x128/0x168)
[ 6.906280@0] [<c03714b8>] (__cpufreq_set_policy+0x128/0x168) from [<c0371758>] (cpufreq_add_dev_interface+0x260/0x2c8)
[ 6.917043@0] [<c0371758>] (cpufreq_add_dev_interface+0x260/0x2c8) from [<c0371c7c>] (cpufreq_add_dev+0x4bc/0x634)
[ 6.927375@0] [<c0371c7c>] (cpufreq_add_dev+0x4bc/0x634) from [<c029aa98>] (sysdev_driver_register+0xb0/0x12c)
[ 6.937356@0] [<c029aa98>] (sysdev_driver_register+0xb0/0x12c) from [<c0370b24>] (cpufreq_register_driver+0x70/0x17c)
[ 6.947947@0] [<c0370b24>] (cpufreq_register_driver+0x70/0x17c) from [<c029d318>] (platform_drv_probe+0x18/0x1c)
[ 6.958101@0] [<c029d318>] (platform_drv_probe+0x18/0x1c) from [<c029c10c>] (driver_probe_device+0x90/0x1ac)
[ 6.967908@0] [<c029c10c>] (driver_probe_device+0x90/0x1ac) from [<c029c2b4>] (__driver_attach+0x8c/0x90)
[ 6.977456@0] [<c029c2b4>] (__driver_attach+0x8c/0x90) from [<c029b32c>] (bus_for_each_dev+0x5c/0x88)
[ 6.986656@0] [<c029b32c>] (bus_for_each_dev+0x5c/0x88) from [<c029baf0>] (bus_add_driver+0x17c/0x244)
[ 6.995944@0] [<c029baf0>] (bus_add_driver+0x17c/0x244) from [<c029c760>] (driver_register+0x78/0x13c)
[ 7.005232@0] [<c029c760>] (driver_register+0x78/0x13c) from [<c029d6c8>] (platform_driver_probe+0x18/0x9c)
[ 7.014959@0] [<c029d6c8>] (platform_driver_probe+0x18/0x9c) from [<c003770c>] (do_one_initcall+0xfc/0x164)
[ 7.024679@0] [<c003770c>] (do_one_initcall+0xfc/0x164) from [<c0008988>] (kernel_init+0x98/0x13c)
[ 7.033617@0] [<c0008988>] (kernel_init+0x98/0x13c) from [<c003e0c0>] (kernel_thread_exit+0x0/0x8)
[ 7.042554@0] ---[ end trace 1b75b31a2719ed1d ]---
[ 7.047327@0] ------------[ cut here ]------------
[ 7.052103@0] WARNING: at /opt/yuetv_release_c2/src/yuetv_2/common/kernel/smp.c:320 smp_call_function_single+0x150/0x1c0()
[ 7.063122@0] Modules linked in:
[ 7.066342@0] [<c0043b44>] (unwind_backtrace+0x0/0xf8) from [<c0061ee4>] (warn_slowpath_common+0x4c/0x64)
[ 7.075887@0] [<c0061ee4>] (warn_slowpath_common+0x4c/0x64) from [<c0061f18>] (warn_slowpath_null+0x1c/0x24)
[ 7.085696@0] [<c0061f18>] (warn_slowpath_null+0x1c/0x24) from [<c008f460>] (smp_call_function_single+0x150/0x1c0)
[ 7.096026@0] [<c008f460>] (smp_call_function_single+0x150/0x1c0) from [<c008f784>] (smp_call_function+0x34/0x68)
[ 7.106268@0] [<c008f784>] (smp_call_function+0x34/0x68) from [<c0049c2c>] (clk_set_rate_a9+0x9c/0xdc)
[ 7.115555@0] [<c0049c2c>] (clk_set_rate_a9+0x9c/0xdc) from [<c0049f28>] (meson_clk_set_rate+0x130/0x168)
[ 7.125103@0] [<c0049f28>] (meson_clk_set_rate+0x130/0x168) from [<c0049ff4>] (clk_set_rate+0x94/0xbc)
[ 7.134391@0] [<c0049ff4>] (clk_set_rate+0x94/0xbc) from [<c0052d28>] (meson_cpufreq_target_locked.isra.2+0x14c/0x224)
[ 7.145067@0] [<c0052d28>] (meson_cpufreq_target_locked.isra.2+0x14c/0x224) from [<c0052e24>] (meson_cpufreq_target+0x24/0x3c)
[ 7.156438@0] [<c0052e24>] (meson_cpufreq_target+0x24/0x3c) from [<c0370570>] (__cpufreq_driver_target+0x50/0x64)
[ 7.166682@0] [<c0370570>] (__cpufreq_driver_target+0x50/0x64) from [<c0372d1c>] (cpufreq_governor_performance+0x28/0x30)
[ 7.177618@0] [<c0372d1c>] (cpufreq_governor_performance+0x28/0x30) from [<c0370658>] (__cpufreq_governor+0xb0/0x138)
[ 7.188207@0] [<c0370658>] (__cpufreq_governor+0xb0/0x138) from [<c03714b8>] (__cpufreq_set_policy+0x128/0x168)
[ 7.198276@0] [<c03714b8>] (__cpufreq_set_policy+0x128/0x168) from [<c0371758>] (cpufreq_add_dev_interface+0x260/0x2c8)
[ 7.209039@0] [<c0371758>] (cpufreq_add_dev_interface+0x260/0x2c8) from [<c0371c7c>] (cpufreq_add_dev+0x4bc/0x634)
[ 7.219368@0] [<c0371c7c>] (cpufreq_add_dev+0x4bc/0x634) from [<c029aa98>] (sysdev_driver_register+0xb0/0x12c)
[ 7.229350@0] [<c029aa98>] (sysdev_driver_register+0xb0/0x12c) from [<c0370b24>] (cpufreq_register_driver+0x70/0x17c)
[ 7.239941@0] [<c0370b24>] (cpufreq_register_driver+0x70/0x17c) from [<c029d318>] (platform_drv_probe+0x18/0x1c)
[ 7.250096@0] [<c029d318>] (platform_drv_probe+0x18/0x1c) from [<c029c10c>] (driver_probe_device+0x90/0x1ac)
[ 7.259904@0] [<c029c10c>] (driver_probe_device+0x90/0x1ac) from [<c029c2b4>] (__driver_attach+0x8c/0x90)
[ 7.269452@0] [<c029c2b4>] (__driver_attach+0x8c/0x90) from [<c029b32c>] (bus_for_each_dev+0x5c/0x88)
[ 7.278653@0] [<c029b32c>] (bus_for_each_dev+0x5c/0x88) from [<c029baf0>] (bus_add_driver+0x17c/0x244)
[ 7.287940@0] [<c029baf0>] (bus_add_driver+0x17c/0x244) from [<c029c760>] (driver_register+0x78/0x13c)
[ 7.297228@0] [<c029c760>] (driver_register+0x78/0x13c) from [<c029d6c8>] (platform_driver_probe+0x18/0x9c)
[ 7.306950@0] [<c029d6c8>] (platform_driver_probe+0x18/0x9c) from [<c003770c>] (do_one_initcall+0xfc/0x164)
[ 7.316671@0] [<c003770c>] (do_one_initcall+0xfc/0x164) from [<c0008988>] (kernel_init+0x98/0x13c)
[ 7.325611@0] [<c0008988>] (kernel_init+0x98/0x13c) from [<c003e0c0>] (kernel_thread_exit+0x0/0x8)
[ 7.334548@0] ---[ end trace 1b75b31a2719ed1e ]---
[ 7.342779@0] ERROR::usb_gadget_probe_driver:1316: usb_gadget_register_driver ENODEV
[ 7.342784@0]
[ 7.349288@0] aml_rtc aml_rtc: setting system clock to 1970-01-01 00:00:12 UTC (12)
[ 7.356342@0] CEC init
[ 7.358776@1] CEC: CEC task process
[ 7.362216@0] i[ 7.386878@0] Changing baud from 0 to 115200
[ 7.446933@0] Freeing init memory: 188K
[ 7.450392@1] init: /init.amlogic.rc: 373: ignored duplicate definition of service 'smbd'
[ 7.453900@1] init (1): /proc/1/oom_adj is deprecated, please use /proc/1/oom_score_adj instead.
[ 7.462543@1] init: try mount debugfs to target /sys/kernel/debug
[ 7.468302@1] init: try mount none to target /proc/bus/usb
[ 7.480523@1] UMP: UMP device driverloaded
[ 7.504792@1] Mali pp1 MMU register mapped at e001e000...
[ 7.504848@1] Mali pp2 MMU register mapped at e00cc000...
[ 7.509973@1] mali_meson_poweron: Mali APB bus accessing
[ 7.515226@1] ..........accessing done.
[ 7.582058@1] mali_meson_poweron: Interrupt received.
[ 7.648808@1] Mali: Mali device driver loaded
[ 8.650017@1] init: try mount none to target /acct
[ 8.687267@0] init: try mount tmpfs to target /mnt/secure
[ 8.687477@0] init: try mount tmpfs to target /mnt/asec
[ 8.692340@0] init: try mount tmpfs to target /mnt/obb
[ 8.698023@0] init: try mount none to target /dev/cpuctl
[ 8.737791@1] init: try mount tmpfs to target /storage/external_storage
[ 8.739037@1] init: try mount /dev/block/system to target /system
[ 8.753480@0] EXT4-fs (system): mounted filesystem with ordered data mode. Opts: noauto_da_alloc
[ 8.757158@0] yaffs: dev is 32505861 name is "mtdblock5" rw
[ 8.762188@0] yaffs: passed flags ""
[ 8.798804@0] init: try mount /dev/block/fastplay to target /fastplay
[ 8.799789@0] vfm_map_store:rm default
[ 8.803385@0] vfm_map_store:add default decoder ppmgr deinterlace amvideo
[ 8.819104@0] init: Before e2fsck_main...
[ 9.061382@0] init: After e2fsck_main...
[ 9.061450@0] init: Before e2fsck_main...
[ 9.063982@0] init: After e2fsck_main...
[ 9.067753@0] init: try mount /dev/block/data to target /data
[ 9.090746@0] EXT4-fs (data): mounted filesystem with ordered data mode. Opts: noauto_da_alloc
[ 9.094233@0] init: try mount /dev/block/cache to target /cache
[ 9.139810@0] EXT4-fs (cache): recovery complete
[ 9.143876@0] EXT4-fs (cache): mounted filesystem with ordered data mode. Opts: noauto_da_alloc
[ 9.147765@0] init: cannot find '/system/bin/check_partition', disabling 'check_partition'
[ 9.155843@0] init: try mount rootfs to target /
[ 9.160587@0] init: try mount tmpfs to target /mnt/secure
[ 9.216546@1] set fail , detect locktable conflict,retry
[ 9.245171@0] init: cannot find '/system/bin/cdnclient', disabling 'cdnclient'
[ 9.282151@0] DSP pcmenc stream buffer to
[ 9.292369@0] init: property 'ro.usb.vendor.string' doesn't exist while expanding '${ro.usb.vendor.string}'
[ 9.317044@0] init: cannot expand '${ro.usb.vendor.string}' while writing to '/sys/class/android_usb/android0/f_mass_storage/vendor_string'
[ 9.324055@0] init: property 'ro.usb.product.string' doesn't exist while expanding '${ro.usb.product.string}'
[ 9.347037@0] init: cannot expand '${ro.usb.product.string}' while writing to '/sys/class/android_usb/android0/f_mass_storage/product_string'
[ 9.357096@0] android_usb:disable, not bind to controller
[ 9.360550@0] android_usb:disable, not bind to controller
[ 9.365387@0] android_usb:enable, not bind to controller
[ 9.380725@0] warning: `adbd' uses 32-bit capabilities (legacy support in use)
root@android:/ # [ 9.431986@0] Write AOBUS=0x0fff0fc3
[ 10.277665@1] kplayer_alsa_ad: open file:/fastplay/adconf.xml failed!
[ 14.686174@0] osd0=>x:1920 ,y:0,w:0,h:0
[ 14.686179@0]osd1=> x:0,y:0,w:0,h:0
[ 14.718817@0] amvdec_h264 probe start.
[ 14.719026@0]
[ 14.719032@0] vh264_init
[ 14.728786@0] Alloc new mc addr to dea54000
[ 14.741674@0] vf_reg_provider:decoder.h264
[ 14.741792@0] vf_reg_provider:ppmgr
[ 14.778733@0] amvdec_h264 probe end.
[ 14.778868@0] tsdemux video_pid = 0x100, audio_pid = 0x101, sub_pid = 0xffff
[ 14.796496@0] v264dec: aspect_ratio not available from source
[ 14.796605@1] dsp_open
[ 14.796611@1] audiodsp prevent sleep
[ 14.809788@1] load firmware from userspace failed: switch to load it by calling request_firmware() in kernel
[ 14.900622@0] load mcode size=148636
[ 14.900629@0] ,load addr 0xc4000000 mcode name audiodsp_codec_aac_helix.bindi_init_buf: version 2013-9-06a, prog_proc_type 0, buf start 8d200000, size 300000, buf(w720,h584) cur num 5 (available 5,total 5)
[ 14.923424@0] vf_reg_provider:deinterlace
[ 14.931916@0] DSP statck start =0x9e310000,size=0x10000
[ 14.934691@0] DSP gp statck start =0x9e16b200,size=0x200
[ 14.947199@0] pre_de_buf_config: source change: 0/0/0/0=>36864/1920/1072/0
[ 14.978984@0] DSP heap start =0x9e800000,size=0x100000
[ 14.986556@0] DSP stream buffer to
[ 14.987203@0] reset dsp : dec opt=fffb, subid=0
[ 15.001437@0] dsp reset now
[ 15.056516@0] frame format changed,fmt->valid 0x1c
[ 15.056668@0] audio info from dsp:sample_rate=48000 channel_num=2
[ 15.064938@0] dsp status=52756e
[ 15.128044@0] substream#0 ptr: dfb72f00 type: playback name: subdevice #0 interface: I2S
[ 15.144953@0] ====== audio_set_aiubuf ======
[ 15.145077@0] I2S hw init,i2s mode 0
[ 15.157363@0] iec958 mode PCM16
[ 15.157512@0] IEC958 16bit
[ 15.157643@0] iec958 nodify hdmi audio type 1
[ 15.185667@0] audio info changed.notify to hdmi: type 1,sr 48000,ch 2
[ 15.186541@0] HDMI: aout notify rate 48000
[ 15.199841@0] HDMI: aout notify format PCM
[ 15.210770@0] audio pts started::::::: 0
[ 15.212774@0] audio pts started::::::: 1
[ 15.267283@1] HDMI: audio channel num is 1
[ 15.267377@1] current VIC: 4
[ 15.268649@1] audio sample rate: 3
[ 15.272016@1] HDMI: reset audio N para
[ 15.284625@1] PCM out to HDMI
[ 15.284700@1] i2s_to_spdif_flag:1
[ 15.285350@1] Enable audio spdif to HDMI
[ 15.301310@1] HDMI Audio Type: PCM
[ 15.301407@1] HDMI: set audio param
[ 15.607166@1] reset apts:0x22803-->0x2a03f, pcr 0x22803, diff 30780
[ 19.502255@0] 333000
[ 21.171889@0] request_suspend_state: wakeup (3->0) at 20905040005 (1970-01-02 00:00:01.798658999 UTC)
[ 21.310095@1] trun off vdac
[ 21.460118@0] netdev_open
[ 21.460204@0] Ethernet reset
[ 21.460273@0] NET MDA descpter start addr=de194000
[ 21.468495@0] phy_reset!
[ 21.468527@0] set_phy_mode() phy_Identifier: 0x7c0f1
[ 21.474023@0] --1--write mac add to:df9a6748: c8 0e 77 02 5b db |..w.[.|
[ 21.478923@0] name=nand_key nand_key
[ 21.482618@0] read:addr:0xfe000000,phy_blk_addr:1016,phy_page_addr:0,aml_nand_get_key:129
[ 21.495928@0] unkown current key-name,key_read_show:1273
[ 21.496037@0] ret = -22
[ 21.496040@0] print_buff=
[ 21.513211@0] --2--write mac add to:df9a6748: c8 0e 77 02 5b db |..w.[.|
[ 21.514336@0] write mac add to:df9a6748: c8 0e 77 02 5b db |..w.[.|
[ 21.521685@0] Current DMA mode=0, set mode=621c100
[ 21.528291@0] ether leave promiscuous mode
[ 21.529463@0] ether leave all muticast mode
[ 21.533565@0] changed the Multicast,mcount=1
[ 21.537847@0] add mac address:33:33:00:00:00:01,bit=1
[ 21.542852@0] set hash low=2,high=0
[ 21.546355@0] changed the filter setting to :4
[ 21.552598@0] changed the Multicast,mcount=1
[ 21.555022@0] add mac address:33:33:00:00:00:01,bit=1
[ 21.564352@0] changed the Multicast,mcount=2
[ 21.564375@0] add mac address:33:33:00:00:00:01,bit=1
[ 21.564383@0] add mac address:01:00:5e:00:00:01,bit=32
[ 21.564388@0] set hash low=2,high=1
[ 21.564392@0] changed the filter setting to :4
[ 21.564772@0] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 21.632711@1] changed the Multicast,mcount=2
[ 21.632789@1] add mac address:33:33:00:00:00:01,bit=1
[ 21.636419@1] add mac address:01:00:5e:00:00:01,bit=32
[ 21.673595@1] init: no such service 'wififix'
[ 21.768960@1] +++dhd_module_init+++
[ 21.769288@1] in
[ 21.770859@1] WIFIDisenable!
[ 21.976876@1] in
[ 21.976968@1] WIFIEnable!
[ 22.367022@1] in
[ 22.367138@1] WIFIEnable!
[ 22.368342@1] in
[ 22.372288@1] WIFIEnable!
[ 22.375194@1]
[ 22.375203@1] SD/MMC initialization started......
[ 23.016972@1] mmc data3 pull high
[ 23.017318@0] sd_mmc_info->card_type=0
[ 23.018432@0] begin SDIO check ......
[ 23.022918@0] Actual delay time in sdio_voltage_validation() = 10 ms
[ 23.087350@1] Got RCA = 1
[ 23.089457@0] #this sdio card could not support read after write
[ 23.090615@0] sd_mmc_init() is completed successfully!
[ 23.095635@0] This SDIO card is working in Wide Bus and at 50MHz High Speed mode!
[ 23.095653@0]
[ 23.108526@0] memorycard0: queuing unknown CIS tuple 0x80 (2 bytes)
[ 23.111106@0] memorycard0: queuing unknown CIS tuple 0x80 (3 bytes)
[ 23.116956@1] monitor : INSERT
[ 23.120903@0] memorycard0: queuing unknown CIS tuple 0x80 (3 bytes)
[ 23.128380@1] memorycard0: queuing unknown CIS tuple 0x80 (7 bytes)
[ 23.176955@1] =========== WLAN placed in POWER ON ========
[ 23.178128@1] bcmsdh_register: Linux Kernel SDIO/MMC Driver
[ 23.182527@1] dhd_customer_oob_irq_map: customer specific Host GPIO number is (100)
[ 23.190918@0] dhdsdio_probe : no mutex held. set lock
[ 23.195591@0] F1 signature read @0x18000000=0x1591a962
[ 23.257024@0] bcmsdh_config_hw_oob_intr: Enable HW OOB for 43362
[ 23.262825@0] DHD: dongle ram size is set to 245760(orig 245760)
[ 23.264559@0] dhd_bus_select_firmware_name_by_chip: firmware_path=/etc/wifi/40181/stable/fw_bcm40181a2.bin
[ 23.275994@0] wl_create_event_handler thr:e5a created
[ 23.279290@0] wl_create_event_handler thr:e5a started
[ 23.289952@1] p2p0: P2P Interface Registered
[ 23.290292@1] dhd_attach thr:e61 created
[ 23.294164@1] dhd_attach thr:e61 started
[ 23.296796@1] dhd_attach thr:e62 created
[ 23.304542@1] dhd_attach thr:e62 started
[ 23.305058@1] dhd_attach thr:e63 created
[ 23.309340@1] dhd_attach thr:e63 started
[ 23.315271@0] Broadcom Dongle Host Driver: register interface MAC: 00:90:4c:11:22:33
[ 23.321204@0] dhdsdio_probe : the lock is released.
[ 23.326407@1] mylin s1 num=2
[ 23.331380@0]
[ 23.331393@0] Dongle Host Driver, version 1.28.23.5 (r)
[ 23.331397@0] Compiled in drivers/net/wireless/bcmdhd on May 13 2014 at 09:49:34
[ 23.447651@0] =========== WLAN placed in RESET ========
[ 23.447694@0] ---dhd_module_init---
[ 25.399020@1] dhd_bus_select_firmware_name_by_chip: firmware_path=/etc/wifi/40181/stable/fw_bcm40181a2.bin
[ 25.403209@1]
[ 25.403225@1] Dongle Host Driver, version 1.28.23.5 (r)
[ 25.403238@1] Compiled in drivers/net/wireless/bcmdhd on May 13 2014 at 09:49:34
[ 25.419601@1] wl_android_wifi_on in
[ 25.525363@1] =========== WLAN going back to live========
[ 25.525663@0]
[ 25.525666@0]
[ 25.525668@0] dhd_bus_devreset: == WLAN ON ==
[ 25.534446@0] dhd_bus_devreset called when dongle is not in reset
[ 25.539361@0] Will call dhd_bus_start instead
[ 25.543495@0] bcmsdh_config_hw_oob_intr: Enable HW OOB for 43362
[ 25.549828@0] dhd_bus_select_firmware_name_by_chip: firmware_path=/etc/wifi/40181/stable/fw_bcm40181a2.bin
[ 25.559556@0] Final fw_path=/etc/wifi/40181/stable/fw_bcm40181a2.bin
[ 25.559572@0] Final nv_path=/etc/wifi/40181/stable/nvram.txt
[ 25.559578@0] Final conf_path=/system/etc/firmware/config.txt
[ 25.603145@0] dhdsdio_write_vars: Download, Upload and compare of NVRAM succeeded.
[ 25.836593@0] dhd_bus_init: enable 0x06, ready 0x06 (waited 0us)
[ 25.837230@0] bcmsdh_set_drvdata: Enter
[ 25.840918@0] bcmsdh_register_oob_intr: Enter
[ 25.845372@0] bcmsdh_register_oob_intr: IRQ=100 Type=414
[ 25.855060@1] Set country ALL, revision 0
[ 25.932228@1] Country code: ALL (ALL/0)
[ 25.940135@1] ------ WIFI Firmware version = wl0: Jul5 2013 17:55:22 version 5.90.195.89.10 FWID 01-f4d31c13
[ 25.944568@1] Driver: 1.28.23.5 (r)
[ 25.944576@1] Firmware: wl0: Jul5 2013 17:55:22 version 5.90.195.89.10 FWID 01-f4d31c13
[ 25.944629@1] wl_android_wifi_on: Success
[ 25.945912@1] wl_cfg80211_attach_post: p2p0 p2p_dev_addr=02:22:f4:b5:67:2a
[ 30.448099@0] osd0 free scale ENABLE
[ 30.448237@0] vf_reg_provider:osd
[ 30.459559@0] vf_light_unreg_provider:ppmgr
[ 30.459596@0] ppmgr rebuild from light-unregister
[ 30.460071@0] osd1 free scale ENABLE
[ 30.477232@1] osd0=>x:0 ,y:0,w:0,h:0
[ 30.477248@1]osd1=> x:0,y:0,w:0,h:0
[ 30.546944@0] <FIQ>:vf_ext_light_unreg_provide
[ 30.546972@0] 0
[ 30.554075@1] vf_unreg_provider:decoder.h264
[ 30.554622@0] vf_unreg_provider:ppmgr
[ 30.556758@0] vf_unreg_provider:deinterlace
[ 30.577000@1] pts missed 10, pts hit 356, pts_outside 0, duration 3840, sync_outside 0, use_idr_framerate 0
[ 30.582439@1] adec_release
[ 30.583999@1] dsp_release
[ 30.587047@1] audiodsp allow sleep
[ 30.660174@0] osd0=>x:0 ,y:0,w:1280,h:720
[ 30.660189@0]osd1=> x:0,y:0,w:18,h:18
[ 30.710723@0] osd0 free scale ENABLE
[ 30.710831@0] vf_reg_provider:osd
[ 30.746933@0] <FIQ>:vf_ext_light_unreg_provide
[ 30.746952@0] 0
[ 32.001956@1] tvmode set to 720p
[ 32.001976@1]
[ 32.002087@1] don't set the same mode as current.
[ 32.054898@1] osd0 free scale ENABLE
[ 32.055009@1] vf_reg_provider:osd
[ 32.060148@0] osd1 free scale ENABLE
[ 32.105935@0] buf=0
[ 32.105952@0]
[ 32.106034@0] IEC958_mode_raw=0
[ 32.146916@0] <FIQ>:vf_ext_light_unreg_provide
[ 32.146938@0] 0
[ 32.149409@1] osd set scale, h_scale: DISABLE, v_scale: DISABLE
[ 32.149437@1] osd.scaledata: 0 0 0 0
[ 32.149457@1] osd.pandata: 0 1279 1080 1799
[ 37.242796@0] trun off vdac
[ 37.776021@1] BT_RADIO going: off
[ 37.776103@1] BCM_BT: going OFF
[ 37.815884@1] BT_RADIO going: on
[ 37.815922@1] BCM_BT: going ON
[ 37.886948@0] Changing baud from 0 to 115200
[ 37.966954@0] Changing baud from 115200 to 115200
[ 38.057658@0] Changing baud from 115200 to 2000000
[ 38.496889@0] Changing baud from 2000000 to 115200
[ 38.776936@0] Changing baud from 115200 to 2000000
[ 39.173928@0] BT_RADIO going: off
[ 39.173971@0] BCM_BT: going OFF
嗯，TTL接口定义，有需要的拿去用。
完……
大神，a31s求遥控移植方法，希望你赐教，朋友反应替换两个文件不起作用强烈支持楼主ing…… 大神，a31s求遥控移植方法，希望你赐教，朋友反应替换两个文件不起作用 lhwxl2012 发表于 2016-1-12 21:58
大神，a31s求遥控移植方法，希望你赐教，朋友反应替换两个文件不起作用强烈支持楼主ing…… ...
测得的码贴上来看看。 大神，求遥控移植方法，希望你赐教，朋友反应替换两个文件不起作用http://updata.wicp.net/2015/27021.swf 帖子精彩，受益匪浅，代码太长了{:89:} 真是太牛逼了 完全看不懂 楼主用心了，内容非常精彩。 大神，看了您的帖子给C1s加TTL，但是接了VCC线，可能接反了导致烧了盒子，但是也不知道到底是哪个零部件烧坏了，求大神指点迷津，现在通电后什么灯也不亮。谢谢！ 很给力，ZNDS有你更精彩！
页:
[1]
2