wokankan 发表于 2015-7-13 16:13
TTl线肯定是好的，因为刷路由器没问题。
什么按回车键上电还是上电有显示后按回车键什么的，就是中断不了 ...
不知道你的TTL 是什么板子
我的上面有指示灯 闪烁
你接受正常就看看 TX（发送）那个端
每次按键盘板子上的指示灯都有回应，不是很明显，
上电后再按键盘 完全来得及，也可能是TTL连接板子的触点不够完全
楼主我也是种情况，烦恼了，到底有没救的啊，是你用ttl刷uboot吗？
能帮我刷下一代魔盒嘛 和你的问题差不多能进RE 刷不进ROM开机卡在小猫钓鱼那
我也出现这种情况，请问不用ttl线刷 可以解决吗？
为什么刷rec总是出现这种错误提示：
NAND read: recovery offset 0x0, size 0x600000
6291456 bytes read: OK
Wrong Image Format for bootm command
ERROR: can't get kernel image!
m6_mbx_g32#mmcinfo
sdio_detect return 1
Device: SDIO Port B
Manufacturer ID: 0
OEM: 0
Name: ATran Speed: 40000000
Rd Block Len: 512
SD version 2.0
High Capacity: Yes
Capacity: 16005464064
Boot Part Size: 0
Bus Width: 4-bit
m6_mbx_g32#fatload mmc 0 82000000 recovery.img
reading recovery.img
6240256 bytes read
m6_mbx_g32#bootm
## Booting kernel from Legacy Image at 82000000 ...
Image Name: Linux-3.0.50-00016-g209edc4
Image Type: ARM Linux Kernel Image (lzma compressed)
Data Size: 3403648 Bytes = 3.2 MiB
Load Address: 80008000
Entry Point:80008000
Verifying Checksum ... OK
Ramdisk start addr = 0x8233f800, len = 0x2b3c3f
Uncompressing Kernel Image ... OK
machid from environment: 0x4e27
EFUSE machid is not set.
Using machid 0x4e27 from environment
Starting kernel ...
[ 3.848564@1] kobject (dfaa0410): tried to init an initialized object, something is seriously wrong.
[ 3.868049@1] dvb_io_setup start
[ 3.872158@1] DVB: cannot get resource "frontend0_LNBON/OFF"
[ 3.872190@1] DVB: cannot get resource "frontend0_POWERON/OFF"
[ 3.878007@1] DVB: cannot get resource "frontend0_ANTOVERLOAD"
[ 3.884630@1] Smartcard: cannot get resource "smc0_reset"
[ 3.990196@1] init: /init.rc: 35: invalid command 'busybox'
[ 4.235943@0] init: cannot open '/initlogo.rle'
[ 4.236528@0] init: Unable to open persistent property directory /data/property errno: 2
~ # [ 4.526739@0] EXT4-fs (cache): VFS: Can't find ext4 filesystem
[ 4.744144@0] EXT4-fs (cache): VFS: Can't find ext4 filesystem
[ 4.984072@0] EXT4-fs (cache): VFS: Can't find ext4 filesystem
[ 5.164034@0] EXT4-fs (cache): VFS: Can't find ext4 filesystem
NAND bbt detect factory Bad block at 5a00000
快速回车后 输入 nand info 提示 not found nand
难道是NAND挂了？
到底用哪个软件输入命令？
输入后提示NAND有错的意思。DATA分区为零 没法修复。。
楼主能不能帮帮忙 我盒子开机蓝灯 遥控没反应 按键不闪，能进re ，ttl修复后还是提示有坏块，可能是系统自带那几个坏块
