线刷遇到问题，请大神修改下
本帖最后由 力量源泉 于 2026-11-3 13:48 编辑Send command: crc32 1000000 4de3085
CRC32 for 01000000 ... 05de3084 ==> 6839654c
(OK)
Send command: unzip 0x1000000 0x20000000
Uncompressed size: 149300656 = 0x8E625B0
(OK)
Send command: mmc write.ext4sp 0x0 0x20000000 0x62f000 0x6e9800
MMC write ext4 sparse: dev # 0, block # 6483968, count 7247872 ...
Writing at 6483984 blk# -- 0% complete.
Writing at 6658064 blk# -- 1% complete.
Writing at 6804096 blk# -- 2% complete.
Writing at 7008256 blk# -- 3% complete.
Writing at 7532544 blk# -- 7% complete.
Writing at 8056832 blk# --10% complete.
Writing at 8581120 blk# --14% complete.
Writing at 9105408 blk# --18% complete.HIMCI_ERROR hi_mci_cmd_done:488: Is Card error: reserved
HIMCI_ERROR hi_mci_cmd_done:488: Is Card error: reserved
HIMCI_ERROR hi_mci_cmd_done:488: Is Card error: reserved
HIMCI_ERROR hi_mci_cmd_done:488: Is Card error: reserved
HIMCI_ERROR hi_mci_cmd_done:488: Is Card error: reserved
HIMCI_ERROR hi_mci_cmd_done:488: Is Card error: status bit
HIMCI_ERROR hi_mci_cmd_done:488: Is Card error: status bit
HIMCI_ERROR hi_mci_cmd_done:488: Is Card error: Device not switch to the expected mode
HIMCI_ERROR hi_mci_cmd_done:488: Is Card error: status bit
HIMCI_ERROR hi_mci_cmd_done:488: Is Card error: status bit
HIMCI_ERROR hi_mci_cmd_done:488: Is Card error: status bit
HIMCI_ERROR hi_mci_cmd_done:488: Is Card error: status bit
HIMCI_ERROR hi_mci_cmd_done:488: Is Card error: status bit
HIMCI_ERROR hi_mci_cmd_done:488: Is Card error: An erase sequence was clearled before excuting
HIMCI_ERROR hi_mci_cmd_done:488: Is Card error: status bit
HIMCI_ERROR hi_mci_cmd_done:488: Is Card error: Only partial address space was erased due to write protected blocks
HIMCI_ERROR hi_mci_cmd_done:488: Is Card error: Cid/csd overwrite
HIMCI_ERROR hi_mci_cmd_done:488: Is Card error: reserved
HIMCI_ERROR hi_mci_cmd_done:488: Is Card error: reserved
HIMCI_ERROR hi_mci_cmd_done:488: Is Card error: Device error related to the execution of the last command
HIMCI_ERROR hi_mci_cmd_done:488: Is Card error: Device error occurred, not related to the host command
HIMCI_ERROR hi_mci_cmd_done:488: Is Card error: Device internal ECC was applied but failed to correct the data
HIMCI_ERROR hi_mci_cmd_done:488: Is Card error: command not legal fo the Device state
HIMCI_ERROR hi_mci_cmd_done:488: Is Card error: the CRC check of the command failed
HIMCI_ERROR hi_mci_cmd_done:488: Is Card error: a sequence or password error happen in lock/unlock device cmd
HIMCI_ERROR hi_mci_cmd_done:488: Is Card error: status bit
HIMCI_ERROR hi_mci_cmd_done:488: Is Card error: Attempt to program a write protected block
HIMCI_ERROR hi_mci_cmd_done:488: Is Card error: An invailid selection of erase groups
HIMCI_ERROR hi_mci_cmd_done:488: Is Card error: An error in the sequence of erase cmd
HIMCI_ERROR hi_mci_cmd_done:488: Is Card error: Block length argument error
HIMCI_ERROR hi_mci_cmd_done:488: Is Card error: Address argument misaligned to device physical blocks
HIMCI_ERROR hi_mci_cmd_done:488: Is Card error: Address out of the allowed range for the device
mmc write failed
Raw data: No.-1 blocks written: ERROR.
(ERROR)
执行命令失败，可能的原因如下：
1.请检查当前单板Flash与烧写分区中的Flash类型是否一致；
2.当前fastboot不支持该命令；
确认是fastboot原因请大神给修改下！附件有原fastboot！
帮顶一下 你这个盒子有可能是高安版，EMMC有写保护，或者是EMMC寿命到了要玩完
页:
[1]
