求助中兴B860AV3.2-T S905L3SB 刷完机黑屏，HDMI无显示
本帖最后由 liubaochuan 于 2025-11-13 11:43 编辑刷机包用的大全里的
试过好几个
919-电信高安版-晶晨（S905L3SB）芯片-2+8G_安卓9.0_线刷固件包
都属无限循环重启 看TTL日志无限循环U-Boot 未找到可启动的 OS 镜像（未进入内核加载阶段） 你要说清楚你机子的完整型号和具体配置,以及你使用的何种刷机工具和刷机包,大家才能帮你想办法解决. post_deleted y598 发表于 2025-11-13 10:38
哪款，加下V: Y-xt855
下次再发这样的回复，我直接举报你 刘小金 发表于 2025-11-13 09:33
你要说清楚你机子的完整型号和具体配置,以及你使用的何种刷机工具和刷机包,大家才能帮你想办法解决. ...
emmc/sd response timeout, cmd55, status=0x1ff2800
init_part() 294: PART_TYPE_AML
mmc init success
init_part() 294: PART_TYPE_AML
eMMC/TSD partition table have been checked OK!
crc32_s:0x1577dad == storage crc_pattern:0x1577dad!!!
crc32_s:0xee152b83 == storage crc_pattern:0xee152b83!!!
crc32_s:0x79f50f07 == storage crc_pattern:0x79f50f07!!!
SDIO Port C: tuning start:
Data 1 aligned delay is 0
SDIO Port C: clk 200000000 tuning start:
SDIO Port C: clk 200000000 tuning start:
SDIO Port C: clk 200000000 tuning start:
SDIO Port C: clk 200000000 tuning start:
SDIO Port C: best_win_start =0, best_win_size =4
meson-mmc: emmc: [ 4 ] is nok
meson-mmc: emmc: [ 0 -- 3 ] is ok
adjust 0x22000, clock 200000000
switch to partitions #0, OK
mmc1(part 0) is current device
Device: SDIO Port C
Manufacturer ID: 2f
OEM: 111
Name: 05S00
Tran Speed: 200000000
Rd Block Len: 512
MMC version 5.1
High Capacity: Yes
Capacity: 7.3 GiB
mmc clock: 200000000
Bus Width: 8-bit
amlmmc erase 1emmckey_is_protected : protect
start = 0,end = 57343
Caution! Your devices Erase group is 0x400
The erase range would be change to 0x36000~0xe9ffff
start = 221184,end = 15335422
usb producing env_relocate
mmc env offset: 0x3ee00000
*** Warning - bad CRC, using default environment
Saving Environment to aml-storage...
mmc env offset: 0x3ee00000
Writing to MMC(1)... done
刷机卡这里 月光※傾城 发表于 2025-11-13 11:01
下次再发这样的回复，我直接举报你
emmc/sd response timeout, cmd55, status=0x1ff2800
init_part() 294: PART_TYPE_AML
mmc init success
init_part() 294: PART_TYPE_AML
eMMC/TSD partition table have been checked OK!
crc32_s:0x1577dad == storage crc_pattern:0x1577dad!!!
crc32_s:0xee152b83 == storage crc_pattern:0xee152b83!!!
crc32_s:0x79f50f07 == storage crc_pattern:0x79f50f07!!!
SDIO Port C: tuning start:
Data 1 aligned delay is 0
SDIO Port C: clk 200000000 tuning start:
SDIO Port C: clk 200000000 tuning start:
SDIO Port C: clk 200000000 tuning start:
SDIO Port C: clk 200000000 tuning start:
SDIO Port C: best_win_start =0, best_win_size =4
meson-mmc: emmc: [ 4 ] is nok
meson-mmc: emmc: [ 0 -- 3 ] is ok
adjust 0x22000, clock 200000000
switch to partitions #0, OK
mmc1(part 0) is current device
Device: SDIO Port C
Manufacturer ID: 2f
OEM: 111
Name: 05S00
Tran Speed: 200000000
Rd Block Len: 512
MMC version 5.1
High Capacity: Yes
Capacity: 7.3 GiB
mmc clock: 200000000
Bus Width: 8-bit
amlmmc erase 1emmckey_is_protected : protect
start = 0,end = 57343
Caution! Your devices Erase group is 0x400
The erase range would be change to 0x36000~0xe9ffff
start = 221184,end = 15335422
usb producing env_relocate
mmc env offset: 0x3ee00000
*** Warning - bad CRC, using default environment
Saving Environment to aml-storage...
mmc env offset: 0x3ee00000
Writing to MMC(1)... done
刷机卡这里 首先你要搞清楚你那盒子的主控是S905L3S-B还是S905L3-B.然后确定是否是高安版的.找对包配合晶晨短接神器就应该刷成功. 买个固件马上就能解决 只不过固件会比你盒子贵 刘小金 发表于 2025-11-13 19:14
首先你要搞清楚你那盒子的主控是S905L3S-B还是S905L3-B.然后确定是否是高安版的.找对包配合晶晨短接神器就 ...
S905L3S-B能刷成功就是开不了机