我需要在验证一下，在刷一下别人的盒子才知道是不是通用的，这个是安徽的 ...
我手上有一个是河南的，可供实验 lfnh2001 发表于 2025-4-5 17:39
我手上有一个是河南的，可供实验
可以分享一下吗大哥 # cat /dev/block/mmcblk0p2 ▒tbootdelay=0verify=nbaudrate=115200ipaddr=192.168.1.10serverip=192.168.1.1netmask=255.255.255.0bootfile="uImage"phy_intf=mii,rgmiiuse_mdio=0,1phy_addr=2,1gmac_debug=0silent=1devkmsg=offloglevel=0quiet=quietsysvnd_rw=0skyargs=if test ${sysvnd_rw} = 1; then setenv bootargs ${bootargs_sysvnd_rw}; fi; setenv bootargs ${bootargs} boardname=${boardname} loglevel=${loglevel} printk.devkmsg=${devkmsg} ${quiet}skycmd=run skyargsbootcmd=run skycmd; mmc read 0 0x8020000 0x10000 0x1000;mmc read 0 0x1FFBFC0 0x38000 0x7800; mmc read 0 0x3FFBFC0 0x19000 0x3C; bootm 0x1FFBFC0 - 0x3FFC000recoverycmd=mmc read 0 0x8020000 0x10000 0x1000;mmc read 0 0x1FFBFC0 0x1000 0xA000;bootm 0x1FFBFC0bootargs=androidboot.hardware=kunlun androidboot.selinux=permissive androidboot.serialno=0123456789 console=ttyAMA0,115200 blkdevparts=mmcblk0:1M(fastboot),512K(bootargs),512K(bootargsbak),20M(recovery),2M(deviceinfo),8M(securestore),2M(atf),8M(baseparam),8M(pqparam),2M(dtbo),10M(logo),10M(logobak),20M(fastplay),20M(recoverybak),20M(boot),8M(misc),8M(macid),16M(skparam),20M(trustedcore),1792M(system)ro,1088M(cache),320M(vendor)ro,10M(private),-(userdata) hbcomp=/dev/block/mmcblk0p20 init=/init root=/dev/mmcblk0p20 androidboot.dtbo_idx=0 pq=noacmuhd printk.time=y nofmc noeth1 rootwait disp_offset_vfs=disablebootargs_sysvnd_rw=androidboot.hardware=kunlun androidboot.selinux=permissive androidboot.serialno=0123456789 console=ttyAMA0,115200 blkdevparts=mmcblk0:1M(fastboot),512K(bootargs),512K(bootargsbak),20M(recovery),2M(deviceinfo),8M(securestore),2M(atf),8M(baseparam),8M(pqparam),2M(dtbo),10M(logo),10M(logobak),20M(fastplay),20M(recoverybak),20M(boot),8M(misc),8M(macid),16M(skparam),20M(trustedcore),1792M(system),1088M(cache),320M(vendor),10M(private),-(userdata) hbcomp=/dev/block/mmcblk0p20 init=/init root=/dev/mmcblk0p20 androidboot.dtbo_idx=0 pq=noacmuhd printk.time=y nofmc noeth1 rootwait disp_offset_vfs=disablerecoverybootargs=androidboot.hardware=kunlun androidboot.selinux=permissive androidboot.serialno=0123456789 console=ttyAMA0,115200 blkdevparts=mmcblk0:1M(fastboot),512K(bootargs),512K(bootargsbak),20M(recovery),2M(deviceinfo),8M(securestore),2M(atf),8M(baseparam),8M(pqparam),2M(dtbo),10M(logo),10M(logobak),20M(fastplay),20M(recoverybak),20M(boot),8M(misc),8M(macid),16M(skparam),20M(trustedcore),1792M(system),1088M(cache),320M(vendor),10M(private),-(userdata) hbcomp=/dev/block/mmcblk0p20 init=/init root=/dev/mmcblk0p20 androidboot.dtbo_idx=0 pq=noacmuhd rootwaitbootargs_512M=mem=512M mmz=ddr,0,0,32M vmalloc=500Mbootargs_768M=mem=768M mmz=ddr,0,0,32M vmalloc=500Mbootargs_1G=mem=1G mmz=ddr,0,0,52M vmalloc=500Mbootargs_2G=mem=2G mmz=ddr,0,0,52M vmalloc=500Mbootargs_3G=mem=3G mmz=ddr,0,0,52M vmalloc=500Mstdin=serialstdout=serialstderr=serialserialoff=1 bootargs 里面关于boot的参数可以看到，关闭了Android串口重定向，serialstdout=serialstderr=serialserialoff=1，需要把最后的1改成0 菜单按10下以上，后按右键，或下键。就会打开开启adb对话框 我也试了 卡码跟你一模一样，你怎么刷的机？
页:
1
[2]