云南移动B860AV3.2-M内存2G只识别1G，帮忙看下（附TTL跑码)
本帖最后由 rinco 于 2024-9-12 22:12 编辑云南移动B860AV3.2-M
B860AV3.2-M，2+8G，S905L3
刷机后变1G内存了，怎么刷都刷不会去了，
求个原机备份，或者其他恢复２G内存的方法
谢谢！
本帖最后由 rinco 于 2024-9-12 22:10 编辑
TTL跑码信息：看样子，是不是内存坏了两颗，这板子一共4颗内存，正面两颗，背面两颗，一颗512M，一共2G，
看TTL有两颗没有识别
又懂的帮忙看下
GXLX2:BL1:3cfee7:42a5ae;FEAT:ADFC318C:0;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 152969
BL2 Built : 13:35:42, Jun1 2021.
gxl g49d5acc - liqiang.hou@droid07-sz
Board ID = 11, adc=843
set vcck to 1070 mv
set vddee to 1070 mv
CPU clk: 1200MHz
DDR4 chl: Rank0+1 @ 912MHz - FAIL
DDR4 chl: Rank0 @ 912MHz
bist_test rank: 0 29 09 4a 34 1a 4f 21 00 42 36 1b 52 26 06 46 32 19 4b 25 05 45 30 16 4b 577 - PASS
Rank0: 1024MB(auto)-2T-18
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x013c0000, size: 0x00007600
Load bl301 from eMMC, src: 0x00018200, des: 0x01380000, size: 0x00002600
Load bl31 from eMMC, src: 0x0001c200, des: 0x10100000, size: 0x00019600
Load bl33 from eMMC, src: 0x00038200, des: 0x01000000, size: 0x0004dc00
NOTICE:BL3-1: v1.0(debug):27617c8a4
NOTICE:BL3-1: Built : 18:02:23, Aug 18 2021
NOTICE:BL31: GXL normal boot!
NOTICE:BL31: BL33 decompress pass
efuse init ops = c5
efuse init hdcp = c, cf9=7
x2_hp_e = 0
bl30: check_permit, count is 1
bl30: check_permit: ok!
chipid: 0 0 3 c c 0 53 b4 88 a0 0 c5 not ES chip
INFO: BL3-1: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader
ERROR: Error initializing runtime service opteed_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x1000000
INFO: BL3-1: Next image spsr = 0x3c9
U-Boot 2015.01 (Oct 21 2021 - 04:30:34), Build: jenkins-J_CMCC_HG680-LY_2_S905L_CMCCGUANGDONG-194
DRAM:1 GiB
Relocation Offset is: 36edf000
gpio: pin GPIODV_25 (gpio 44) value is 1
register usb cfg = 0000000037f5d738
[**]** init
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
vpp: vpp_init
MMC: aml_priv->desc_buf = 0x0000000033ecfac0
aml_priv->desc_buf = 0x0000000033ed1de0
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x1ff2800
emmc/sd response timeout, cmd55, status=0x1ff2800
init_part() 293: PART_TYPE_AML
mmc init success
dtb magic 00088b1f
Amlogic multi-dtb tool
GZIP format, decompress...
Multi dtb detected
unified board, board id = 11
Multi dtb tool version: v2 .
Support 6 dtbs.
aml_dt soc: gxlx2 platform: p291 variant: 1g
dtb 0 soc: gxlx2 plat: p291 vari: 1g
dtb 1 soc: gxlx2 plat: p291 vari: 2g
dtb 2 soc: gxlx2 plat: p291 vari: 3g
dtb 3 soc: gxlx2 plat: p295 vari: 1g
dtb 4 soc: gxlx2 plat: p295 vari: 2g
dtb 5 soc: gxlx2 plat: p295 vari: 3g
Find match dtb: 0
start dts,buffer=0000000033ed4610,dt_addr=0000000033ed4610
Amlogic multi-dtb tool
Single dtb detected
parts: 17
00: logo 0000000000800000 1
01:recovery 0000000001800000 1
02: misc 0000000000800000 1
03: dtbo 0000000000800000 1
04:cri_data 0000000000800000 2
05: param 0000000001000000 2
06: boot 0000000001000000 1
07: rsv 0000000001000000 1
08:metadata 0000000001000000 1
09: vbmeta 0000000000200000 1
10: tee 0000000002000000 1
11: vendor 0000000014000000 1
12: odm 0000000008000000 1
13: system 0000000050000000 1
14: product 0000000008000000 1
15: cache 0000000046000000 2
16: data ffffffffffffffff 4
init_part() 293: PART_TYPE_AML
eMMC/TSD partition table have been checked OK!
check pattern success
mmc env offset: 0x4d400000
In: serial
Out: serial
Err: serial
board id is : 11
hpd_state=1
do_hpd_detect: hdmimode=720p50hz
do_hpd_detect: colorattribute=444,8bit
is invalid for cvbs.
set hdmitx VIC = 19
config HPLL = 2970000
HPLL: 0xc000027b
config HPLL done
j = 3vid_clk_div = 1
hdmitx: set enc for VIC: 19
hdmitx phy se**ng done
rx version is 1.4 or belowdiv=10
hdmtix: set audio
To run cmd
_verify_dtb_checksum()-924: calc 263c811d, store 263c811d
_verify_dtb_checksum()-924: calc 263c811d, store 263c811d
dtb_read()-1046: total valid 2
dtb_read()-1113: do nothing
Amlogic multi-dtb tool
GZIP format, decompress...
Multi dtb detected
unified board, board id = 11
Multi dtb tool version: v2 .
Support 6 dtbs.
aml_dt soc: gxlx2 platform: p291 variant: 1g
dtb 0 soc: gxlx2 plat: p291 vari: 1g
dtb 1 soc: gxlx2 plat: p291 vari: 2g
dtb 2 soc: gxlx2 plat: p291 vari: 3g
dtb 3 soc: gxlx2 plat: p295 vari: 1g
dtb 4 soc: gxlx2 plat: p295 vari: 2g
dtb 5 soc: gxlx2 plat: p295 vari: 3g
Find match dtb: 0
Net: eth_initialize:396 dwmac.c9410000 idx:0
amlkey_init() enter!
keynum is 4
: tee size: 0
wipe_data=successful
wipe_cache=successful
ext4logoLoadCmd=ext4load mmc 1:${logoPart} ${logoLoadAddr} ${ext4LogoPath}
6220854 bytes read in 186 ms (31.9 MiB/s)
load bmp from ext4 part okay
bmp pixel: 24
load fb addr from dts
fb_addr for logo: 0x3f800000
load fb addr from dts
fb_addr for logo: 0x3f800000
[**]addr=0x3f800000 width=5760, height=2160
ERR: 24 bit/pixel mode2, but BMP has 24 bit/pixel
upgrade_step=2
upgrade_step12=2
amlkey_init() enter!
amlkey_init() 70: already init!
keynum is 4
: tee size: 0
Error:fL507:key not programed yet
Error:fL507:key not programed yet
Error:fL507:key not programed yet
Error:fL507:key not programed yet
Error:fL507:key not programed yet
key1 = 7d82dd22
key2 = 7e81dd22
key3 = 728ddd22
time_out = 7a120
ir init
irkey - irkey key_value1 key_value2 key_value3 time_value
Usage:
可以用E900V22E等2+8G，S905L3的固件线刷 rinco 发表于 2024-9-11 13:59
机顶盒买来还没备份，那时也不知道咋备份，就着急蛮荒的刷了网上下载的固件，于是就杯具了
...
可以用E900V22E等2+8G，S905L3的固件线刷 本帖最后由 rinco 于 2024-9-12 10:56 编辑
月光※傾城 发表于 2024-9-11 15:16
可以用E900V22E等2+8G，S905L3的固件线刷
你有E900V22E等2+8G固件吗，分享一个给我吧，感谢！ 月光※傾城 发表于 2024-9-11 15:16
可以用E900V22E等2+8G，S905L3的固件线刷
能看到的E900V22E固件刷了个遍，B860AV3.2的固件也刷了个遍，要么刷不进去，要么还是只识别1G
我也是，，这盒子有毒，很多人都说刷了只有1G DDR4 chl: Rank0+1 @ 912MHz - FAIL
DDR4 chl: Rank0 @ 912MHz
bist_test rank: 0 29 09 4a 34 1a 4f 21 00 42 36 1b 52 26 06 46 32 19 4b 25 05 45 30 16 4b 577 - PASS
Rank0: 1024MB(auto)-2T-18 22e，是安卓4的啊？ 一样 这么刷都不行 这个盒子有毒 我也是云南的 什么包都刷不进去 百毒不侵那种
页:
[1]
2
