巧虎小红盒刷机求助。
本帖最后由 智能小柠檬 于 2023-9-18 16:42 编辑手上有个巧虎小红盒，型号：R1200。原系统需要巧虎账号登录。问了巧虎官方客户说已被别人绑定，我不能使用。只能刷机了，拆开一开，具然焊了串口线。只是比常规的串口线小且细，接上去容易掉。折腾了好一会，才看到ttl跑码。
GXL:BL1:9ac50e:bb16dc;FEAT:ADFC318C:0;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 142278
BL2 Built : 14:57:36, Nov4 2016.
gxl g5990442 - xiaobo.gu@droid05
set vcck to 1070 mv
set vddee to 1070 mv
Board ID = 7, adc=544
CPU clk: 1200MHz
2layers board, use ddr_set
DDR chl: Rank0+1 @ 792MHz - FAIL
DDR chl: Rank0 @ 792MHz - PASS
DQS-corr enabled
DDR scramble enabled
Rank0: 1024MB(auto)-2T-11
DataBus test pass!
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x01100000, size: 0x00007400
Load bl301 from eMMC, src: 0x00018200, des: 0x01200000, size: 0x00002200
Load bl31 from eMMC, src: 0x0001c200, des: 0x10100000, size: 0x00019400
Load bl33 from eMMC, src: 0x00038200, des: 0x01000000, size: 0x00084000
NOTICE:BL3-1: v1.0(debug):959fdf0
NOTICE:BL3-1: Built : 15:01:44, Dec 29 2016
aml log : bl31 normal boot !
bl30: check_permit, count is 1
bl30: check_permit: ok!
chipid: 0 0 3 c c 0 56 b3 80 a0 0 e4 not ES chip
efuse init ops = e4
efuse init hdcp = c, cf9=7
sINFeOc:u r e tBaLs3k- 1s:t aIrnti!ti
alizing runthiimgehsteavices
WARNING: No OPTEE provided by BL2 boot loader
ERROR: Error initializing runtime service opteed_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x1000000
INFO: BL3-1: Next image spsr = 0x3c9
U-Boot 2015.01-g2875563-dirty (Jun 21 2019 - 04:42:43)
DRAM:1 GiB
Relocation Offset is: 36eef000
gpio: pin GPIODV_24 (gpio 43) value is 1
mwm 0xc8837004: with ok
mwm 0xc883700c: with ok
mwm 0xc8837010: with ok
mwm 0xc8837010: with ok
register usb cfg = 0000000037f632f8
canvas init
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
MMC: aml_priv->desc_buf = 0x0000000033edfac0
aml_priv->desc_buf = 0x0000000033ee1de0
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
mmc refix success
mmc init success
mmc read lba=0x14000, blocks=0x400
Amlogic multi-dtb tool
Multi dtb detected
2layers board, board id use 7
Multi dtb tool version: v2 .
Support 6 dtbs.
aml_dt soc: gxl platform: p211 variant: 1g
dtb 0 soc: gxbb plat: p201 vari: 1g
dtb 1 soc: gxbb plat: p201 vari: 2g
dtb 2 soc: gxl plat: p211 vari: 1g
dtb 3 soc: gxl plat: p211 vari: 2g
dtb 4 soc: gxl plat: p215 vari: 1g
dtb 5 soc: gxl plat: p215 vari: 2g
Find match dtb: 2
start dts,buffer=0000000033ee4630,dt_addr=0000000033ef5e30
parts: 12
00: logo 0000000002000000 1
01:recovery 0000000002000000 1
02: rsv 0000000000800000 1
03: tee 0000000000800000 1
04: crypt 0000000002000000 1
05: misc 0000000002000000 1
06: instaboot 0000000020000000 1
07: boot 0000000002000000 1
08: system 0000000040000000 1
09: cache 0000000020000000 2
10:cus_config 0000000020000000 2
11: data ffffffffffffffff 4
get_dtb_struct: Get emmc dtb OK!
overide_emmc_partition_table: overide cache
skip partition cache.
Partition table get from SPL is :
name offset size flag
===================================================================================
0: bootloader 0 400000 0
1: reserved 2400000 4000000 0
2: cache 6c00000 20000000 2
3: env 27400000 800000 0
4: logo 28400000 2000000 1
5: recovery 2ac00000 2000000 1
6: rsv 2d400000 800000 1
7: tee 2e400000 800000 1
8: crypt 2f400000 2000000 1
9: misc 31c00000 2000000 1
10: instaboot 34400000 20000000 1
11: boot 54c00000 2000000 1
12: system 57400000 40000000 1
13: cus_config 97c00000 20000000 2
14: data b8400000 119c00000 4
mmc read lba=0x12000, blocks=0x2
mmc read lba=0x12002, blocks=0x2
mmc_read_partition_tbl: mmc read partition OK!
eMMC/TSD partition table have been checked OK!
mmc env offset: 0x27400000
In: serial
Out: serial
Err: serial
board id is : 7
hpd_state=0
cvbs performance type = 7, table = 1
To run cmd
read emmc dtb
Amlogic multi-dtb tool
Multi dtb detected
2layers board, board id use 7
Multi dtb tool version: v2 .
Support 6 dtbs.
aml_dt soc: gxl platform: p211 variant: 1g
dtb 0 soc: gxbb plat: p201 vari: 1g
dtb 1 soc: gxbb plat: p201 vari: 2g
dtb 2 soc: gxl plat: p211 vari: 1g
dtb 3 soc: gxl plat: p211 vari: 2g
dtb 4 soc: gxl plat: p215 vari: 1g
dtb 5 soc: gxl plat: p215 vari: 2g
Find match dtb: 2
Net: dwmac.c9410000
Error: dwmac.c9410000 address not set.
wipe_data=successfulSecd
wipe_cache=successful
bmp pixel: 16
addr=0x3d800000 width=2560, height=1440
upgrade_step=2
amlkey_init() enter!
keynum is 4
: tee size: 0
Error:fL507:key not programed yet
gpio: pin GPIOAO_2 (gpio 102) value is 1
key1 = b649ff00
key2 = b649fd01
key3 = 728ddd22
time_out = 30d40
ir init
irkey - irkey key_value1 key_value2 key_value3 time_value
Usage:
irkey
rebootmode=cold_boot
Hit any key to stop autoboot:0
ee_gate_off ...
## Booting Android Image at 0x01080000 ...
reloc_addr =33f0c210
copy done
Amlogic multi-dtb tool
Single dtb detected
load dtb from 0x1000000 ......
Uncompressing Kernel Image ... OK
kernel loaded at 0x01080000, end = 0x01ff2c18
Loading Ramdisk to 33c57000, end 33edcb07 ... OK
Loading Device Tree to 000000001fff3000, end 000000001ffff02a ... OK
signature:
fdt_instaboot: get header err
Starting kernel ...
uboot time: 2054228 us
[ 0.000000@0] Initializing cgroup subsys cpu
[ 0.000000@0] Initializing cgroup subsys cpuacct
[ 0.000000@0] Linux version 3.14.29-gc47bd4e5ae2-dirty (colin@ter) (gcc version 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.09 - Linaro GCC 4.9-2014.09) ) #4 SMP PREEMPT Thu Dec 12 03:10:25 EST 2019
[ 0.000000@0] CPU: armv71 Processor revision 4
[ 0.000000@0] bootconsole enabled
get_dvfs_info 0007
INFO: HDCP22 key read fail!
INFO: p1d 0
INFO: pd1 0
root@p201_iptv:/ #
CPU是晶晨的S905M。不知道能不能刷机？用哪个固件刷机？请大老们帮忙指导一下。
本帖最后由 智能小柠檬 于 2023-9-18 16:43 编辑
昨天晚上不能上传图片，今天补图。
貌似没有这个盒子的链接，我个人建议如果觉得这个盒子系统不好用的话，可以换个智慧盒子，比如当贝盒子H3，当贝盒子H3是当贝2023年首发的电视盒子新品，堪称电视盒子新标杆、质价比超群、兼具实用与美感、加量不加价。当贝盒子H3外观独创内置电源，机器内置电源适配器，摆脱适配器占插排位置困扰，同时在盒子内部加入了散热系统，方便动态功率调整，轻载动态高效。
CPU方面，当贝盒子H3搭载瑞芯微RK3566，4核A55芯片，嵌入式配备多种功能强大的硬件引擎，频率提升到1.8GHz；GPU方面，当贝盒子H3则采用了Mail G52-2EE，支持多路视频源8K解码，智能增强色彩表现。内存方面，当贝盒子H3采用2GB的DDR4闪存，再配合32GB的大存储，解码能力更强，也更流畅；
系统配置上，当贝盒子H3内置当贝OS系统是电视盒子中最流畅也是最稳定的机顶盒系统。秉承“轻、快、自由”，UI设计非常的人性化，支持桌面主题自定义布局，可以随心将自己喜欢的应用放在更便捷的位置。
页:
[1]
