数码视讯Q7刷机问题
S905L3的处理器线刷成功，以下是ttl跑码信息：BL2 Built : 13:36:55, Jun 22 2020.gxl g85d6ad1 - longyong.chen@droid02-sz
Board ID = 7, adc=528
set vcck to 1070 mv
set vddee to 1070 mv
CPU clk: 1200MHz
BL2 USB
DDR3 chl: Rank0+1 @ 912MHz - FAIL
DDR3 chl: Rank0 @ 912MHz
bist_test rank: 0 1b 03 34 31 1a 48 18 00 30 3b 23 54 17 00 2f 37 25 4a 16 00 2c 39 23 50 637 - PASS
Rank0: 1024MB(auto)-2T-13
0.0;
TE: 2264653
BL2 Built : 13:36:55, Jun 22 2020.
gxl g85d6ad1 - longyong.chen@droid02-sz
Board ID = 7, adc=524
set vcck to 1070 mv
set vddee to 1070 mv
CPU clk: 1200MHz
BL2 USB
0.0;
TE: 2462040
BL2 Built : 13:36:55, Jun 22 2020.
gxl g85d6ad1 - longyong.chen@droid02-sz
Board ID = 7, adc=525
set vcck to 1070 mv
set vddee to 1070 mv
CPU clk: 1200MHz
BL2 USB
Load fip header from USB, src: 0x0000c000, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from USB, src: 0x00010000, des: 0x013c0000, size: 0x00007600
Load bl301 from USB, src: 0x00018000, des: 0x01380000, size: 0x00002200
Load bl31 from USB, src: 0x0001c000, des: 0x10100000, size: 0x00019600
Load bl33 from USB, src: 0x00038000, des: 0x01000000, size: 0x00047200
NOTICE:BL3-1: v1.0(debug):361f8a7
NOTICE:BL3-1: Built : 16:43:26, Dec 19 2018
NOTICE:BL31: GXL normal boot!
NOTICE:BL31: BL33 decompress pass
efuse init ops = c5
efuse init hdcp = c, cf9=7
x2_hp_e = 0
bl30: check_permit, count is 1
bl30: check_permit: ok!
chipid: 0 0 3 c c 0 31 b4 a8 a0 0 c5 not ES chip
INFO: BL3-1: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader
ERROR: Error initializing runtime service opteed_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x1000000
INFO: BL3-1: Next image spsr = 0x3c9
U-Boot 2015.01-ge9754dd-dirty (Sep 08 2021 - 17:28:43)
DRAM:1 GiB
Relocation Offset is: 36eef000
MMC init in usb
aml_priv->desc_buf = 0x0000000033edf630
aml_priv->desc_buf = 0x0000000033ee1950
SDIO Port B: 0, SDIO Port C: 1
Enter USB burn
Set Addr 46
Get DT cfg
Get DT cfg
Get DT cfg
set CFG
ID
tplcmd[ echo 12345]
12345
ret = 0
success
BULKcmd[ low_power]
success
ID
tplcmd[ download mem dtb normal 262144]
Down(mem) part(dtb) sz(0x40000) fmt(normal)
totalSlotNum = 0, nextWriteBackSlot 4
success
Burn Start...
load dt.img to 0x0000000001000000, sz=0x40000
Burn complete
BULKcmd
success
BULKcmd
dtb magic 08088b1f
Amlogic multi-dtb tool
GZIP format, decompress...
Multi dtb detected
2layers board, board id use 7
Multi dtb tool version: v2 .
Support 10 dtbs.
aml_dt soc: gxlx2 platform: p291 variant: 1g
dtb 0 soc: gxl plat: p211 vari: 1g
dtb 1 soc: gxl plat: p215 vari: 1g
dtb 2 soc: gxlx plat: p261 vari: 1g
dtb 3 soc: gxlx plat: p261 vari: 2g
dtb 4 soc: gxlx plat: p265 vari: 1g
dtb 5 soc: gxlx plat: p265 vari: 2g
dtb 6 soc: gxlx2 plat: p291 vari: 1g
dtb 7 soc: gxlx2 plat: p291 vari: 2g
dtb 8 soc: gxlx2 plat: p295 vari: 1g
dtb 9 soc: gxlx2 plat: p295 vari: 2g
Find match dtb: 6
start dts,buffer=0000000007700000,dt_addr=0000000007700000
Amlogic multi-dtb tool
Single dtb detected
parts: 16
00: logo 0000000002000000 1
01:recovery 0000000002000000 1
02: rsv 0000000000800000 1
03: tee 0000000000800000 1
04: crypt 0000000002000000 1
05: misc 0000000002000000 1
06: instaboot 0000000020000000 1
07: boot 0000000002000000 1
08: system 0000000040000000 1
09: cache 0000000020000000 2
10: params 0000000004000000 2
11: ctc 0000000012c00000 2
12: bootfiles 0000000020000000 2
13: private 0000000000800000 2
14: flashdata 0000000004000000 2
15: data ffffffffffffffff 4
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
emmc/sd read error, cmd8, status=0xa3ff2004
emmc/sd read error, cmd8, status=0x3ff2004
mmc init success
eMMC/TSD partition table have been checked OK!
check pattern success
switch to partitions #0, OK
mmc1(part 0) is current device
Device: SDIO Port C
Manufacturer ID: 15
OEM: 100
Name: 8GTF4
Tran Speed: 52000000
Rd Block Len: 512
MMC version 5.1
High Capacity: Yes
Capacity: 7.3 GiB
mmc clock: 40000000
Bus Width: 1-bit
start erase dtb......
start = 81920,end = 82943
dev # 1,, several blocks erased OK
To run cmd
dtb_write()-1147: valid 0
dtb_write()-1167: new stamp 0, checksum 0x2d38433b, version 1, magic A~D
dtb magic 08088b1f
Amlogic multi-dtb tool
GZIP format, decompress...
Multi dtb detected
2layers board, board id use 7
Multi dtb tool version: v2 .
Support 10 dtbs.
aml_dt soc: gxlx2 platform: p291 variant: 1g
dtb 0 soc: gxl plat: p211 vari: 1g
dtb 1 soc: gxl plat: p215 vari: 1g
dtb 2 soc: gxlx plat: p261 vari: 1g
dtb 3 soc: gxlx plat: p261 vari: 2g
dtb 4 soc: gxlx plat: p265 vari: 1g
dtb 5 soc: gxlx plat: p265 vari: 2g
dtb 6 soc: gxlx2 plat: p291 vari: 1g
dtb 7 soc: gxlx2 plat: p291 vari: 2g
dtb 8 soc: gxlx2 plat: p295 vari: 1g
dtb 9 soc: gxlx2 plat: p295 vari: 2g
Find match dtb: 6
start dts,buffer=0000000001000000,dt_addr=0000000001000000
dtb magic edfe0dd0
Amlogic multi-dtb tool
Single dtb detected
start dts,buffer=0000000001000000,dt_addr=0000000001000000
Amlogic multi-dtb tool
Single dtb detected
parts: 16
00: logo 0000000002000000 1
01:recovery 0000000002000000 1
02: rsv 0000000000800000 1
03: tee 0000000000800000 1
04: crypt 0000000002000000 1
05: misc 0000000002000000 1
06: instaboot 0000000020000000 1
07: boot 0000000002000000 1
08: system 0000000040000000 1
09: cache 0000000020000000 2
10: params 0000000004000000 2
11: ctc 0000000012c00000 2
12: bootfiles 0000000020000000 2
13: private 0000000000800000 2
14: flashdata 0000000004000000 2
15: data ffffffffffffffff 4
partition table success
usb producing env_relocate
mmc env offset: 0x27400000
Amlogic multi-dtb tool
Single dtb detected
success
ID
tplcmd
flash LOGIC partCap 0x2000000B
Down(store) part(boot) sz(0x7d6000) fmt(normal)
totalSlotNum = 0, nextWriteBackSlot 1
success
Burn Start...
Burn complete
BULKcmd
success
BULKcmd
Verify Start...
To verify part boot in fmt normal
Verify End
VERIFY OK
success
ID
tplcmd
flash LOGIC partCap 0x2000000B
Down(store) part(logo) sz(0x2000000) fmt(normal)
totalSlotNum = 0, nextWriteBackSlot 1
success
Burn Start...
Burn complete
BULKcmd
success
BULKcmd
Verify Start...
To verify part logo in fmt normal
Verify End
VERIFY OK
success
ID
tplcmd
flash LOGIC partCap 0x2000000B
Down(store) part(recovery) sz(0xd03000) fmt(normal)
totalSlotNum = 0, nextWriteBackSlot 1
success
Burn Start...
Burn complete
BULKcmd
success
BULKcmd
Verify Start...
To verify part recovery in fmt normal
Verify End
VERIFY OK
success
ID
tplcmd
flash LOGIC partCap 0x40000000B
Down(store) part(system) sz(0x210958d8) fmt(sparse)
totalSlotNum = 0, nextWriteBackSlot 1024
success
Burn Start...
Burn complete
Downloading %100
BULKcmd
success
BULKcmd
Verify Start...
To verify part system in fmt sparse
Verify End
VERIFY OK
success
ID
tplcmd
Down(store) part(bootloader) sz(0x1ffe00) fmt(normal)
totalSlotNum = 0, nextWriteBackSlot 32
success
Burn Start...
mmc switch to boot0 success
mmc switch to boot1 success
mmc switch to user success
align bootloader sz from 0x1ffe00 to 0x200000
Burn complete
BULKcmd
success
BULKcmd
mmc switch to boot0 success
mmc switch to boot1 success
mmc switch to user success
VERIFY OK
success
BULKcmd
## save_setting ##
Set upgrade_step to 2
Saving Environment to aml-storage...
mmc env offset: 0x27400000
Writing to MMC(1)... done
success
BULKcmd
Pls un-plug USB line to poweroff
success
但是重启后无法启动系统，ttl跑码显示如下，：
GXLX2:BL1:3cfee7:42a5ae;FEAT:ADFC318C:0;POC:3;RCY:0;EMMC:0;READ:4;READ:4;READ:4;SD:800;USB:8;LOOP:1;EMMC:0;READ:4;READ:4;READ:4;SD:800;USB:8;LOOP:2;EMMC:0;READ:4;READ:4;READ:4;SD:800;USB:8;LOOP:3;EMMC:0;READ:4;READ:4;READ:4;SD:800;USB:8;LOOP:4;EMMC:0;READ:4;READ:4;READ:4;SD:800;USB:8;LOOP:5;EMMC:0;READ:4;READ:4;READ:4;SD:800;USB:8...（一直循环，LOOP值增加）
制作TF启动卡，仍无法启动系统，ttl跑码显示如下：
BL2 Built : 17:04:12, Jun 21 2016.
gxl g21e86b3 - yao.zhang@droid07
set vcck to 1080 mv
set vddee to 1050 mv
Board ID = 8
CPU clk: 1200MHz
DDR chl: Rank0+1 @ 792MHz - FAIL
DDR chl: Rank0 @ 792MHz - PASS
DQS-corr enabled
DDR scramble enabled
GXLX2:BL1:3cfee7:42a5ae;FEAT:ADFC318C:0;POC:3;RCY:0;EMMC:0;READ:4;READ:4;READ:4;SD:0;READ:0;0.0;CHK:0;
no sdio debug board detected
TE: 163960
有没有遇到相同问题的玩家，另外正常的线刷包一般2、3分钟就能刷完，而现在同样大小的线刷包至少耗时5分多钟，不知道什么原因造成的。
这类盒子被不断的精进，有一些刷机固件出来，这些刷机固件能解决的问题非常多，例如电视盒子卡顿、机顶盒死机，甚至是机顶盒变砖黑屏，都可能会被就活。所以的人通过刷机延长使用寿命，但是配置方面一直是硬伤，早已经和时代脱轨，安装了几款软件就会出现死机现象，已经不再是刷机能够解决的了。
https://data.znds.com/attachment/forum/202303/08/105026mrrdqtfcifinqrih.png
众多电视盒子新品中，我最想推荐的就是当贝MAX 1电视盒子，当贝MAX 1是首款采用6G运存的电视盒子，搭配64G的超大内存，配备瑞芯微RK3566芯片，其性能完全秒杀晶晨S905系列和全志芯片，让体验变得更加的流畅，享受到的功能也是越来越多。
https://data.znds.com/attachment/forum/202303/08/105027fzqm0tm2ytfttnmn.gif
https://data.znds.com/attachment/forum/202303/08/105027r12zirr2up6itvtz.jpg
其次就是当贝OS系统，它没有软件的安装限制，可随意安装多款应用，并且UI交互设计流畅，并且具备人性化设计，支持自定义桌面编辑，让用户使用的更加舒心。
https://data.znds.com/attachment/forum/202303/08/105027jt5kxy25yb7uq2dj.gif
这样的一款产品才是目前市场上主流的电视盒子应该具备的素质，如果说价格和你的预期不等，你也完全可以看看当贝盒子H2，虽然只有2+16G的内存，但是拥有晶晨S912八核处理器的芯片，其性能也是这类盒子无法比的。
https://data.znds.com/attachment/forum/202303/08/105027dhpkiy77i27dykyk.png
没有DTB文件分享码？
页:
[1]