ttl显示求解？ 各位大佬帮忙看看
本帖最后由 呆若木鸡哦 于 2021-12-26 17:32 编辑GXBB:BL1:08dafd:0a8993;FEAT:FDFD31BC;POC:3;RCY:0;EMMC:0;READ:0;CHK:0;TE: 163838no sdio debug board detectedBL2 Built : 19:04:11, May 27 2016.gxb g4e33a6f - xiaobo.gu@droid05Board ID = 0set vcck to 1100 mvset vddee to 1050 mvCPU clk: 1536MHzDDR chl: Rank0+1 same @ 912MHzDQS-corr enabledDDR0: 1024MB(auto)-2T-13DataBus test pass!AddrBus test pass!Load fip header from eMMC, src: 0x0000c000, des: 0x01400000, size: 0x00004000New fip structure!Load bl30 from eMMC, src: 0x00010000, des: 0x01700000, size: 0x0000ab40aml log : RSA-1024 check pass!Sending bl30...........................................OK.Run bl30...Load bl301 from eMMC, src: 0x0001c000, des: 0x01700000, size: 0x00001d90aml log : RSA-1024 check pass!Wait bl30...DoneSending bl301........OK.Run bl301...eMMC, src: 0x00020000, des: 0x01700000, size: 0x000122c0--- UART initialized after reboot ---bl30: check_permit, count is 1bl30: check_permit: ok!chipid: ef be ad de d f0 ad ba ef be ad de not ES chipefuse init ops = 13efuse init hdcp = c, cf9=7aml log : RsSecAu-re t1as0k2 s4tart!sheck hpiaghs stask! tLoad bl33 from eMMC, src: 0x00034000, des: 0x01700000, size: 0x0009fc60aml log : RSA-1024 check pass!NOTICE:BL3-1: v1.0(debug):4c66217NOTICE:BL3-1: Built : 17:13:36, Jan 28 2016INFO: BL3-1: Initializing runtime servicesWARNING: No OPTEE provided by BL2 boot loaderERROR: Error initializing runtime service opteed_fastINFO: BL3-1: Preparing for EL3 exit to normal worldINFO: BL3-1: Next image address = 0x1000000INFO: BL3-1: Next image spsr = 0x3c9U-Boot 2015.01-ga449b19 (Sep 11 2017 - 11:26:41)DRAM:1 GiBRelocation Offset is: 36ed4000register usb cfg = 0000000037f630f0register usb cfg = 0000000037f63110register usb cfg = 0000000037f63130vpu detect type: 5vpu clk_level = 7set vpu clk: 666667000Hz, readback: 666660000Hz(0x300)boot_device_flag : 1Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.init bus_cycle=6, bus_timing=8, system=5.0nsreset failedget_chip_type and ret:fffffffeget_chip_type and ret:fffffffechip detect failed and ret:fffffffenandphy_init failed and ret=0xfffffff1MMC: aml_priv->desc_buf = 0x0000000033ec4770aml_priv->desc_buf = 0x0000000033ec6900SDIO Port B: 0, SDIO Port C: 1emmc/sd response timeout, cmd8, status=0x3ff2800emmc/sd response timeout, cmd55, status=0x3ff2800 mmc init successmmc read lba=0x14000, blocks=0x400 Amlogic multi-dtb tool Single dtb detectedstart dts,buffer=0000000033ec8ff0,dt_addr=0000000033ec8ff0parts: 1300: logo 0000000002000000 101:recovery 0000000002000000 102: rsv 0000000000800000 103: tee 0000000000800000 104: crypt 0000000002000000 105: misc 0000000002000000 106: instaboot 0000000020000000 107: boot 0000000002000000 108: system 0000000040000000 109: cache 0000000020000000 210:recovery_bak 0000000002000000 111: backup 0000000020000000 212: data ffffffffffffffff 4get_dtb_struct: Get emmc dtb OK!overide_emmc_partition_table: overide cache skip partition cache.Partition table get from SPL is : name offset size flag=================================================================================== 0: bootloader 0 400000 0 1: reserved 2400000 4000000 0 2: cache 6c00000 20000000 2 3: env 27400000 800000 0 4: logo 28400000 2000000 1 5: recovery 2ac00000 2000000 1 6: rsv 2d400000 800000 1 7: tee 2e400000 800000 1 8: crypt 2f400000 2000000 1 9: misc 31c00000 2000000 110: instaboot 34400000 20000000 111: boot 54c00000 2000000 112: system 57400000 40000000 113: recovery_bak 97c00000 2000000 114: backup 9a400000 20000000 215: data bac00000 117400000 4mmc read lba=0x12000, blocks=0x2mmc read lba=0x12002, blocks=0x2mmc_read_partition_tbl: mmc read partition OK!eMMC/TSD partition table have been checked OK!mmc env offset: 0x27400000In: serialOut: serialErr: serialTo run cmdread emmc dtb Amlogic multi-dtb tool Single dtb detectedNet: Meson_Ethernetwipe_data=successfulwipe_cache=successfulupgrade_step=2reboot_mode=cold_boothpd_state=0addr=0x3f800000 width=3840, height=1440Not find '576cvbs' mapped VICamlkey_init() enter!
盒子怎么了 leidada269 发表于 2021-12-26 21:38
盒子怎么了
卡logo
页:
[1]
