CM201-2求助啊
进过TTL安装当贝桌面没有问题和电视软件HDP/腾讯视频等，但是发现这个盒子好像升级了，每次打开的时候都会报错或者无法播放视频。 有通用的刷机包可以去掉这个原机系统吗？Bootrom start
Boot Media: NAND
Decrypt auxiliary code ...OK
lsadc voltage min: 000002FF, max: 00000303, aver: 00000301, index: 00000001
Enter boot auxiliary code
Auxiliary code - v1.00
DDR code - V1.1.2 20160205
Build: Sep7 2017 - 01:06:39
Reg Version:v1.5.4\
Reg Time: 2017/12/19 12:00:55
Reg Name: hi3798mv3dml_hi3798mv300_LPDDR3-1600_1GB_32bitx1_4layers.reg
DDRS
Boot auxiliary code success
Bootrom success
System startup
Relocate Boot
Jump to C code
Fastboot 3.3.0 (songyuzheng@TSD182) (Jan 03 2018 - 16:24:09)
Fastboot: Version 3.3.0
Build Date: Jan3 2018, 16:25:10
CPU: Hi3798Mv300
Boot Media: NAND
DDR Size: 1GB
Found flash memory controller hifmc100.
Nand ID: 0x2C 0x64 0x44 0x4B 0xA9 0x00 0x00 0x00
Nand: Micron MT29F256G08CMCBB Read-Retry ONFI DDR 2.3
Nand(HW-Auto): Block:2MB Page:8KB OOB:744B ECC:40bit/1k Chip:8GB*1
MMC/SD controller initialization.
No MMC device found !
*** Warning - bad CRC or NAND, using default environment
Net: upWarning: failed to set MAC address
, gmac0Warning: failed to set MAC address
Boot Env on NAND
Env Offset: 0x00100000
Env Size: 0x00010000
Env Range: 0x00010000
*** Warning - Env offset is NOT aligned to NAND Flash block size, environment value is read only.
Get ID_WORD lock flag : 0
SDK Version: spc012cp0001_v2017120708
nand<2>
begin
partition addr :
partition addr :
part_addr:0x200000, part_size:0x400000, offset:0x0, bytes:0xb10
cksum , ptable->checksum
data at 0x0 is ok
part_addr:0x200000, part_size:0x400000, offset:0x0, bytes:0xb10
cksum , ptable->checksum
0 fastboot 0x000000000 0x000200000
0 partition 0x000200000 0x000800000
0 recovery 0x000A00000 0x002800000
0 recovery2 0x003200000 0x002800000
0 misc 0x005A00000 0x000800000
0 mlcverify 0x006200000 0x001000000
0 swdevinfo 0x007200000 0x001000000
0 baseparam 0x008200000 0x000800000
0 baseparam2 0x008A00000 0x000800000
0 pqparam 0x009200000 0x000800000
0 logo 0x009A00000 0x000800000
0 logo2 0x00A200000 0x000800000
0 fastplay 0x00AA00000 0x003C00000
0 fastplay2 0x00E600000 0x003C00000
0 boot 0x012200000 0x002800000
0 boot2 0x014A00000 0x002800000
0 trustedcore 0x017200000 0x002800000
0 securestore 0x019A00000 0x000800000
0 swdb 0x01A200000 0x015E00000
0 cache 0x030000000 0x032000000
0 system 0x062000000 0x040000000
0 userdata 0x0A2000000 0x000000000
nand flash partition no fs_flags
ptable info:2M(fastboot),8M(partition),40M(recovery),40M(recovery2),8M(misc),16M(mlcverify),16M(swdevinfo),8M(baseparam),8M(baseparam2),8M(pqparam),8M(logo),8M(logo2),60M(fastplay),60M(fastplay2),40M(boot),40M(boot2),40M(trustedcore),8M(securestore),350M(swdb),800M(cache),1024M(system),-(userdata) ubi.mtd=swdb ubi.mtd=cache ubi.mtd=system ubi.mtd=userdata ubi.mtd=swdb ubi.mtd=cache ubi.mtd=system ubi.mtd=userdata
tmp_bootargs_env=mtdparts=hinand:2M(fastboot),8M(partition),40M(recovery),40M(recovery2),8M(misc),16M(mlcverify),16M(swdevinfo),8M(baseparam),8M(baseparam2),8M(pqparam),8M(logo),8M(logo2),60M(fastplay),60M(fastplay2),40M(boot),40M(boot2),40M(trustedcore),8M(securestore),350M(swdb),800M(cache),1024M(system),-(userdata) ubi.mtd=swdb ubi.mtd=cache ubi.mtd=system ubi.mtd=userdata ubi.mtd=swdb ubi.mtd=cache ubi.mtd=system ubi.mtd=userdata
partition : ok
sw_devinfo_init begin
part_addr:0x7200000, part_size:0x1000000, offset:0x0, bytes:0x8461c
part_addr:0x7a00000, part_size:0x1000000, offset:0x0, bytes:0x8461c
version :
ok! msg->checksum:0xf0be, crc16:0xf0be
devinfo_init begin
ok! msg->checksum:0x0, crc16:0x0
sw_devinfo_init OK
part_addr:0x12200000, part_size:0x2800000, offset:0x0, bytes:0x2000
use boot cmdline,enable serial, cmdline:
use nand m_cmdline: mem=1Gmmz=ddr,0,0,48M vmalloc=500M flashcache=10 quiet console=ttyAMA0,115200 nanddbgfs=+ecc_notice,+read_retry_notice,+read_retry,+dump,+ecc_count,+read_count,+erase_count lpj=974848 mtdparts=hinand:2M(fastboot),8M(partition),40M(recovery),40M(recovery2),8M(misc),16M(mlcverify),16M(swdevinfo),8M(baseparam),8M(baseparam2),8M(pqparam),8M(logo),8M(logo2),60M(fastplay),60M(fastplay2),40M(boot),40M(boot2),40M(trustedcore),8M(securestore),350M(swdb),800M(cache),1024M(system),-(userdata) ubi.mtd=swdb ubi.mtd=cache ubi.mtd=system ubi.mtd=userdata ubi.mtd=swdb ubi.mtd=cache ubi.mtd=system ubi.mtd=userdata
sw_ir_detect begin 500 count
sw_ir_detect ok
bootargs:
start
mlcverify_offset:0x6200000
mlcverify_info_size:2584
part_addr:0x6200000, part_size:0x800000, offset:0x0, bytes:0xa18
start...
checksum:96a1, pmlcverify_info->checksum:96a1
ok,checksum:0x96a1
data at 0x006200000 is ok
maigic:MLCVERIFY!, count:10, time:1515752848
partition0: recovery(c3a000) verify_value:1add
partition1: recovery2(c3a000) verify_value:1add
partition2: baseparam(2000) verify_value:8336
partition3: baseparam2(16ac) verify_value:1c4e
partition4: logo(30000) verify_value:db3a
partition5: logo2(30000) verify_value:db3a
partition6: fastplay(0) verify_value:0
partition7: fastplay2(0) verify_value:0
partition8: boot(963000) verify_value:d0c5
partition9: boot2(963000) verify_value:d0c5
ok
partname: logo
find logo in mlcverify
part_addr:0x9a00000, part_size:0x800000, offset:0x0, bytes:0x30000
verify logo OK
partname: baseparam
find baseparam in mlcverify
part_addr:0x8200000, part_size:0x800000, offset:0x0, bytes:0x2000
verify baseparam OK
begin
OK
part_addr:0x5a00000, part_size:0x800000, offset:0x0, bytes:0x10000
boot normal!!!
partname: boot
find boot in mlcverify
part_addr:0x12200000, part_size:0x2800000, offset:0x0, bytes:0x963000
verify boot OK
bootm now: bootm 0x1FFFFC0
ok
Reserve Memory
Start Addr: 0xFFFE000
Bound Addr: 0x8D99000
FreeAddr: 0xF0A8000
Alloc Block:Addr Size
0xFBFD000 0x400000
0xF8FC000 0x300000
0xF8F9000 0x2000
0xF878000 0x80000
0xF5D4000 0x2A3000
0xF24F000 0x384000
0xF24B000 0x3000
0xF0B5000 0x195000
0xF0AB000 0x9000
0xF0A8000 0x2000
begin
close loader keyed
Check Hisilicon_ADVCA ...
Not hisilicon ADVCA image ...
Found Initrd at 0x04E00000 (Size 747485 Bytes), align at 2048 Bytes
## Booting kernel from Legacy Image at 020007c0 ...
Image Name: Linux-3.18.24_hi3798mv2x
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 9092184 Bytes = 8.7 MiB
Load Address: 02000000
Entry Point:02000000
Loading Kernel Image from 0x33556480 to 0x33554432 ... OK
OK
There are some conflict between "booargs" and "bootargs_1G".
The param "mmz " in "bootargs_1G" will be ignored.
ATAGS , 1276Bytes
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
>>>init /disk2/zhangchaoyang/SDK/Hisi3798MV300_mlc/device/hisilicon/bigfish/sdk/source/kernel/linux-3.18.y/drivers/usb/usbir/usb-ir.cusb_usbir_init
UBI error: ubi_attach_mtd_dev: mtd18 is already attached to ubi0
UBI error: ubi_init: cannot attach mtd18
UBI error: ubi_attach_mtd_dev: mtd19 is already attached to ubi1
UBI error: ubi_init: cannot attach mtd19
UBI error: ubi_attach_mtd_dev: mtd20 is already attached to ubi2
UBI error: ubi_init: cannot attach mtd20
UBI error: ubi_attach_mtd_dev: mtd21 is already attached to ubi3
UBI error: ubi_init: cannot attach mtd21
init: /init.bigfish.rc: 55: invalid command 'getprop'
init: /init.bigfish.rc: 114: invalid option 'sdcard_r'
init: could not import file '/init.sunniwell.rc' from '/init.rc'
init: /dev/hw_random not found
init: cannot open '/initlogo.rle'
init: /dev/hw_random not found
init: call cmd SYS_GET_CHIPPACKAGETYPE failed :Invalid argument
init: reg_value = 0xffffffff
init: read reg value failed
init: name:mac,value:54:C5:7A:42:8E:E1
init: name:serialno,value:003201FF0001061001B154C57A428EE1
init: name:secureline,value:100
init: name:deviceid,value:111001610512259
init: sw_properties_init end..
healthd: wakealarm_init: timerfd_create failed
healthd: No charger supplies found
init: cannot find '/system/bin/rild', disabling 'ril-daemon'
init: cannot find '/system/bin/dbus-daemon', disabling 'dbus'
init: cannot find '/system/bin/teecd', disabling 'teecd'
init: cannot find '/system/bin/frontPanel', disabling 'frontPanel'
init: cannot find '/system/bin/dtvserver', disabling 'dtvserver'
init: cannot find '/system/bin/gpio-led', disabling 'gpio-led'
init: cannot find '/system/bin/usb-driver', disabling 'usb-driver'
init: property 'sys.powerctl' doesn't exist while expanding '${sys.powerctl}'
init: powerctl: cannot expand '${sys.powerctl}'
init: property 'sys.sysctl.extra_free_kbytes' doesn't exist while expanding '${sys.sysctl.extra_free_kbytes}'
init: cannot expand '${sys.sysctl.extra_free_kbytes}' while writing to '/proc/sys/vm/extra_free_kbytes'
root@Hi3798MV300:/ # init: sys_prop: permission denied uid:1002name:persist.bt.fwdump
init: untracked pid 1979 exited
init: sys_prop: permission denied uid:1000name:ro.config.gfx2d_compose
init: untracked pid 1981 exited
root@Hi3798MV300:/ # init: sys_prop: permission denied uid:1000name:persist.ethernet.on
移动魔百和CM201-2（EMMC/NAND）通用破解固件下载_中国移动魔百盒_ZNDShttps://www.znds.com/tv-1145500-1-1.html 不好意思，要是没找到 楼主是想要破解教程吗，可以在固件中心看看https://www.znds.com/rom/,TTL就可以 daffdg 发表于 2018-3-25 07:41
楼主是想要破解教程吗，可以在固件中心看看https://www.znds.com/rom/,TTL就可以
有我就不用发帖问啦大哥，没有这个版本的 eswgdeh 发表于 2018-3-25 07:39
不好意思，要是没找到
没找到怎么了？ 我的刷了后，跟你一样停在logo上面了，在用ttl，总是无限循环程序，根本输入不了命令 我的也是
同是天涯沦落人 同问，
刷了当贝，还是自动跳会移动之家页面。
TTL也刷不了，下了两个固件，都刷不动。
页:
[1]