求解zxv10 b860av1.1-t不能TTL线刷
本帖最后由 kingtt1994 于 2018-3-18 18:32 编辑求大神帮忙,已经按照论坛上的stp方法,提示:pc工具不支持stb的加密方式,再TTL,
exit_reason:0x06
set vddee to 0x042emv
set vddee to 0x044cmv
[ 1/init ] SysRq : Emergency Remount R/O
[ 1/init ] reboot: Restarting system(init) with command ''
INFO: PSCI Affinity Map:
INFO: AffInst: Level 0, MPID 0x0, State ON
INFO: AffInst: Level 0, MPID 0x1, State ON
INFO: AffInst: Level 0, MPID 0x2, State ON
INFO: AffInst: Level 0, MPID 0x3, State ON
bl31 reb▒GXL:BL1:9ac50e:a1974b;FEAT:ADFD318C;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 63196
BL2 Built : 19:31:35, Jul 25 2017.
gxl g4bbe26f-dirty - liang.yang@droid11-sz
Board ID = 8, adc=620
set vcck to 1070 mv
set vddee to 1070 mv
CPU clk: 1200MHz
Can't match board id, use default ddr_set
DDR type: DDR3-ID
DQS-corr enabled
DDR scramble enabled
Pull down ddr cke
DDR3 chl: Rank0+1 @ 792MHz - FAIL
DDR3 chl: Rank0 @ 792MHz - PASS
Rank0: 1024MB(auto)-2T-11
DataBus test pass!
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x01100000, size: 0x00007400
Load bl301 from eMMC, src: 0x00018200, des: 0x01200000, size: 0x00002200
Load bl31 from eMMC, src: 0x0001c200, des: 0x10100000, size: 0x00019400
Load bl33 from eMMC, src: 0x00038200, des: 0x01000000, size: 0x000de200
NOTICE:BL3-1: v1.0(debug):27d2eea5
NOTICE:BL3-1: Built : 14:56:35, Mar 24 2017
aml log : bl31 normal boot !
bl30: check_permit, count is 1
bl30: check_permit: ok!
chipid: ef be ad de d f0 ad ba ef be ad de not ES chip
efuse init ops = e2
efuse init hdcp = c, cf9=7
seIcNFO: BL3-1: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader
ERROR: Error initializing runtime service opteed_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x1000000
INFO: BL3-1: Next image spsr = 0x3c9
er
t
0aUs-kB osotta rt!2
r15hi.g0h1 -tga7s4k4 1sbtda1r-td!i
-tylo w( Ntoavs k2 9s t2a0r1t7!
15:16:53)
DRAM:1 GiB
gpio: pin GPIOCLK_1 (gpio 99) value is 1
gpio: pin GPIOAO_6 (gpio 106) value is 1
reboot_mode=normal
: tee size: 0
set osd_size 720p
bootmode:NORM
OK
uboot time: 1735716 us
[ 0.000000@0][ 0/swapp] Initializing cgroup subsys cpu
[ 0.000000@0][ 0/swapp] Initializing cgroup subsys cpuacct
[ 0.000000@0][ 0/swapp] CPU: ARMv71 Processor revision 4
[ 0.000000@0][ 0/swapp] no prop version_code
[ 0.000000@0][ 0/swapp] bootconsole enabled
get_dvfs_info 0008
INFO: HDCP22 key read fail!
INFO: p1d 0
INFO: pd1 0
[ 1.1▒root@p200_2G:/ # [ 11.545741@1][ 5166/Threa] monitor: received netlink message:ztebw ok
[ 11.546536@1][ 5166/Threa] monitor:reply
https://www.znds.com/jc/list/256.html参考教程中心 茄子炖排骨 发表于 2018-3-18 18:31
https://www.znds.com/jc/list/256.html参考教程中心
谢谢回复帮忙,已经按照教程操作安装好当贝,原来就这么简单 没有链接WiFi选项 怎么办 可以，看下你电脑版本，我用WIN7可以，打来中兴配置工具，打开ADB
我的也一样，那步错了，请指正 xiaoyu8866 发表于 2018-3-31 13:40
我的也一样，那步错了，请指正
我的后来跟了教程后就可以安装了，也不用TTL，很简单的 楼主威武啊,ZNDS有你更给力！ 如何解决了？ jasonlai 发表于 2018-3-18 19:24
谢谢回复帮忙,已经按照教程操作安装好当贝,原来就这么简单
用哪个方法呢？
页:
[1]
2