中兴ZXV10 B860AV1.1刷机问题求解
本帖最后由 山阴路的夏天 于 2018-2-1 14:06 编辑AC_ON
MIU0_DQS-OK
BIST0-▒▒▒
MIU0-1024_U
Start uboot
Relocation Offset is: 015d7000
U-Boot 2011.06-00120-g7a77291-dirty (Jan 02 2018 - 22:29:27)
miu opencreate instance at 54ee9418 with private size 80 bytes at 54e e9460
create instance at 54ee94b8 with private size 52 bytes at 54ee9500
uboot held at ,size=013220a0
CPU: Clippers
Board: BD_MST207C_D01A_S_CLIPPERS
DRAM:864 MiB
Now running in RAM - U-Boot at: 55100000
eMMC: HS200 200MHz
eMMC 7.28 GB
In: serial
Out: serial
Err: serial
Net: zte_shutdow =false
No ethernet found.
Set MAC default
MAC:0x0: 0x30: 0x1b: 0xba:0x2: 0xdb
msIR_Initialize
cpu opencreate instance at 54ef99c0 with private size 44 bytes at 54e f9a08
CPUIoctl - MDrv_CMD_CPU_QueryClock
close moduleNames: MODULE_CPU
### main_loop entered: s is true
### main_loop entered: bootdelay=1
Starting logo
============= set bootargs ===============
COMControlFlag=> value=, val=0
zte_mac=74:97:81:5F:85:2D,ethaddr=74:97:81:5F:85:2D
Hit any key to stop autoboot: 1@
step1 error...
abort=0 0
mxy: MAEKET_IS_SDLT=0,MarketCode=32, OperatorsCode=3
do_bootcheck called
MMC_CAPACITY_512 =15269880
current emmc size is =0xe8fff8 (should by 512)
MMCusrdata_size =11773944
current userdata size =0xb3a7f8 (should by 512)
this is 8G emmc
get_boot1_ver cmd_boot1=mmc read.boot 1 0x25000000 0x0 0x200000
set hdmi hdcp mode 0!
Saving Environment to MMC...
Writing to MMC(0)... 128 blocks written: OK
128 blocks written: OK
done
iTVStandard2Resolution = 2
value = 534104162101344000007497815F852D
COMControlFlag=> value=, val=0
ethaddr =74:97:81:5F:85:2D
jy ....
search ....
waldo msIR_GetIRKeyCode line:483 breturn false
fore uup IRKey
BootMode=0
search ....
waldo msIR_GetIRKeyCode line:483 breturn false
fore uup IRKey
BootMode=0
search ....
waldo msIR_GetIRKeyCode line:483 breturn false
fore uup IRKey
BootMode=0
search ....
waldo msIR_GetIRKeyCode line:483 breturn false
fore uup IRKey
BootMode=0
search ....
waldo msIR_GetIRKeyCode line:483 breturn false
fore uup IRKey
BootMode=0
search ....
waldo msIR_GetIRKeyCode line:483 breturn false
fore uup IRKey
BootMode=0
search ....
waldo msIR_GetIRKeyCode line:483 breturn false
fore uup IRKey
BootMode=0
search ....
waldo msIR_GetIRKeyCode line:483 breturn false
fore uup IRKey
BootMode=0
search ....
waldo msIR_GetIRKeyCode line:483 breturn false
fore uup IRKey
BootMode=0
search ....
waldo msIR_GetIRKeyCode line:483 breturn false
fore uup IRKey
BootMode=0
BootMode=0
PATCH FOR zte BEGIN
Watchdog_enable TRUE
Watchdog start, MAXTIME 120
create instance at 54ef9bb0 with private size 256 bytes at 54ef9bf8
MDrv_PNL_Init u32PnlRiuBaseAddr = 1f200000
MDrv_PNL_Init u32PMRiuBaseAddr = 1f000000
PNL:
pstPanelInitData->u16Width=1280, pstPanelInitData->u16 Height=720
u16HTotal=1980,u16VTotal=750,pstPanelInitData->u16HTot al=1980,pstPanelInitData->u16VTotal=750, u16DefaultVFreq=500
pstPanelInitData->u16Width=1280, pstPanelInitDa ta->u16Height=720
u16HTotal=1980,u16VTotal=750,pstPanelInitData-> u16HTotal=1980,pstPanelInitData->u16VTotal=750, u16DefaultVFreq=500
PNL:CalculateLPLLSETbyDClk u32KHz = 742500000, u64DefaultLdHz = 742500000
PNL:CalculateLPLLSETbyDClk u32LpllSet = 3531df
No instance existed, please get an instance by call ing MApi_XC_Init() first
msHdmitx_Disp_Init
create instance at 54ef9d00 with private size 1720 bytes at 54ef9d48
no need to patchcreate instance at 54efa948 with private size 80 bytes at 54efa 990
Rx Support HDMI mode!
setHDMITxAnalogTuning: Error: MApi_HDMITx_GetRxDCInfoFromEDID EDID is not ready, at 262
shift -8 pixels in PAL mode
Create Dolby single part name task failed!! ERROR!!! HV SD H input = 0, HVSD H output = 720
ERROR!!! HVSD V input = 0, HVSD V output = 576
bEnable = 0, bIsDNR2VE = 0
lyndon Hal_VE_Set_PreVSD 1mmc change mount : tvcustomer
Size of file "/720.jpg" from mmc device 0 partition tvcustomer: 473547 bytes
Loading file "/720.jpg" at offset 0x0 from mmc device 0 partition tvcustomer
473547 bytes read
create instance at 54efa9e8 with private size 304 bytes at 54efaa30
close moduleNames: MODULE_NJPEG_EX
create instance at 54efa9e8 with private size 132280 bytes at 54efaa30
gop opencreate instance at 54f1aef0 with private size 6908 bytes at 5 4f1af38
mxy--> ir_recovery is 0
mxy: ir_recovery is 0...
## Booting kernel from Legacy Image at 25000800 ...
Image Name: MStar-linux
Image Type: ARM Linux Multi-File Image (uncompressed)
Data Size: 5317739 Bytes = 5.1 MiB
Load Address: 20208000
Entry Point:20208000
Contents:
Image 0: 4627400 Bytes = 4.4 MiB
Image 1: 690327 Bytes = 674.1 KiB
## Loading init Ramdisk from multi component Legacy Image at 25000800 ...
-usb_stop(USB_PORT0)
-usb_stop(USB_PORT1)
-usb_stop(USB_PORT2)
Loading Multi-File Image ... OK
Starting kernel ...
, not expected dram size: 0x0
#######################################################################
# , miu kernel protect is not enabled on second dram #
#######################################################################
Uncompressing Linux... done, booting the kernel.
KERN-3.10.23.001049551
tommy: thread_info_cache_init
mtdoops: mtd device (mtddev=name/number) must be supplied
ready init mutex
after init mutex
RBQP_BASE = 51604000
init: /init.clippers.rc: 455: ignored duplicate definition of service 'mdnsd'
init: /zte_init.rc: 32: ignored duplicate definition of service 'IptvQosServ'
init: /zte_init.rc: 38: ignored duplicate definition of service 'xiriservice'
init: /zte_init.rc: 48: ignored duplicate definition of service 'softdetector'
init: ## ProductID: strlen (32)!
healthd: No charger supplies found
init: cannot find '/system/bin/xiriservice_ChinaMobile_SiChuan', disabling 'blue toothd'
init: cannot find '/system/bin/bleservice', disabling 'bleservice'
init: cannot find '/data/data/com.android.smart.terminal.dplatform/bin/IptvQosSe rv', disabling 'IptvQosServ'
init: cannot find '/system/bin/stratky.sh', disabling 'stratky'
同样的问题等待解决
我也出现同样问题，请问lz后来怎样了？ TTL线接错，需要严格按照教程图示接线，魔百盒类机顶盒有时将TTL线接错，也可以正常跑码，但是无法输入代码 土豆炒玉米 发表于 2018-2-1 16:44
TTL线接错，需要严格按照教程图示接线，魔百盒类机顶盒有时将TTL线接错，也可以正常跑码，但是无法输入代码 ...
我试了，只有这样接采跑码的。可能是更移动有权限了，我第一次好的，昨天被移动强行更新就不行了 amw_roX24 发表于 2018-9-7 11:52
我也出现同样问题，请问lz后来怎样了？
我也是同样的问题，需要怎么处理呢？ 楼主的问题解决了么？我也遇到同样的问题 楼主的问题解决了么？我也遇到同样的问题 同样问题！！！{xiaolu6}等待解决！
页:
[1]