首页 › ZNDS刷机/救砖 › 咪咕盒子MG101 MG100 TTL不跑码解决办法以及刷机过程分享

dpscdp... 发表于 2018-8-30 18:36

又见一个好帖，果断先马克mark收藏了!

204051 发表于 2018-8-30 20:47

又见一个好帖，果断先马克mark收藏了!

flash60 发表于 2018-8-31 15:43

1211111111111111111111111111111111

305778551 发表于 2018-8-31 16:29

ZNDS的教程简直男默女泪啊！

shb110119 发表于 2018-8-31 21:33

此楼主日后必成大器！

999藏宝 发表于 2018-9-1 14:22

老铁666！必须支持一波！

xxffhhbb 发表于 2018-9-1 18:59

高手在当贝啊！学习了

fogang 发表于 2018-9-2 14:17

找一个方法，来用。

maomao1714 发表于 2018-9-3 20:32

谢谢谢谢

htf7782414 发表于 2018-9-4 08:32

焊接好以后，跑马，最后出现一堆哈哈哈，而且不能输命令。
Starting kernel ...

Uncompressing Linux... done, booting the kernel.
unionman private == 220
libphy: PHY himii:1f not found
CMD0 err 0
CMD0 err 0
CMD0 err 0
init: /init.bigfish.rc: 78: invalid option 'sdcard_r'
init: load loaderdb finish!
init: start set ro.product.model:MG100-U3
init: /dev/hw_random not found
init: cannot open '/initlogo.rle'
init: Start mount system t:1
init: End mount t:1
init: Start mount userdata t:1
init: firstboot:1
CMD0 err 0
init: End mount t:1
init: Start mount cache t:1
init: End mount t:1
init: Start mount keydata t:1
init: End mount t:1
init: /dev/hw_random not found
healthd: No charger supplies found
init: cannot find '/system/bin/rild', disabling 'ril-daemon'
init: cannot find '/system/bin/dbus-daemon', disabling 'dbus'
CMD0 err 0
init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery'
init: cannot find '/system/bin/frontPanel', disabling 'frontPanel'
init: cannot find '/system/bin/mtkbt', disabling 'blueangel'
init: cannot find '/system/bin/dtvserver', disabling 'dtvserver'
init: cannot find '/system/bin/gpio-led', disabling 'gpio-led'
init: cannot find '/system/bin/usb-driver', disabling 'usb-driver'
init: property 'sys.powerctl' doesn't exist while expanding '${sys.powerctl}'
init: powerctl: cannot expand '${sys.powerctl}'
init: property 'sys.sysctl.extra_free_kbytes' doesn't exist while expanding '${sys.sysctl.extra_free_kbytes}'
init: cannot expand '${sys.sysctl.extra_free_kbytes}' while writing to '/proc/sys/vm/extra_free_kbytes'
CMD0 err 0
----------------HAHAHAHHAHAHA-----------------
----------------HAHAHAHHAHAHA-----------------
----------------HAHAHAHHAHAHA-----------------
----------------HAHAHAHHAHAHA-----------------
----------------HAHAHAHHAHAHA-----------------
----------------HAHAHAHHAHAHA-----------------
----------------HAHAHAHHAHAHA
----------------HAHAHAHHAHAHA aready modify
killiflytek.sh start

用HItool上载，串口都选择的是对的，且按了上载后再给机器上电，出现：
串口已经连接，请给单板上电，若已经上电，请断电后重新上电。
Bootrom start
Boot from eMMC
发送头帧失败，可能的原因如下：
1.烧写的Fastboot镜像与当前单板型号不匹配导致
2.单板DDR有问题，无法正常进行DDR初始化操作
下载文件失败！
Failed to download boot! Please reset the board, try again.

查看完整版本: 咪咕盒子MG101 MG100 TTL不跑码解决办法以及刷机过程分享